Steel wire VR-1, VR-2, VR-3, VR-4, VR-5 in Yekaterinburg
BP steel wire is a separate type of rolled metal, used mainly as a raw material for creating meshes (reinforcement, road or masonry) and other metal products for industrial sectors. In Yekaterinburg, you can buy BP wire at a favorable price from a reliable distributor of rolled metal - the Metallinvest-Ekaterinburg company.
Production and characteristics of BP wire
The raw material for the production of BP periodic wire is wire rod made of low-carbon steel 1-3 ps, kp with a carbon content of less than 0.2%. The wire rod is pulled on rollers, which form diametrical indentations (0.1-0.3 mm deep in increments of up to 0.3 cm) along the entire length of the wire. This corrugation gives the product better adhesion to concrete.
There are two grades of BP steel wire:
- I - ordinary wire (low-carbon for non-prestressing reinforcement);
- II - high-strength wire (carbon for prestressing reinforcement).
The surface should have no defects other than scratches and rust.
Standard diameter and weight of one meter of VR wire:
- 0.3 cm - 52 g;
- 0.4 cm - 92 g;
- 0.5 cm - 144 g.
Upon customer's request, it is possible to produce BP wire with a diameter from 0.25 to 0.48 cm.
BP wire supplies in Yekaterinburg
You can buy BP steel wire and other high-quality rolled metal products of a wide range in Yekaterinburg on favorable terms from the Metallinvest-Ekaterinburg company. To do this, just fill out the application form on our website.
We cooperate with leading Russian metal rolling plants and supply high-quality BP steel wire from Yekaterinburg to any region of Russia. All products presented in the Metallinvest-Ekaterinburg company catalog have certificates and comply with standards.
By purchasing steel wire from us, you receive:• a batch of goods of any volume you ordered;• prompt packaging;• support of the transaction at all stages;• a wide range of additional services - from processing of rolled metal and its loading in Yekaterinburg to delivery to your site;
• convenient form of payment, discounts, loans;
The Metallinvest-Ekaterinburg company values the client’s time and is aimed at long-term cooperation.
Name Type Size Steel grade GOST| Wire | VR-1 | GOST 6727-80 |
| Wire | VR-3 | GOST 6727 |
| Wire | VR-4 | GOST 6727 |
| Wire | VR-5 | GOST 6727 |
Source: https://ekb.m-invest.ru/metalloprokat/sortovoj-prokat/provoloka/provoloka/
Wire VR-1
PRICES REDUCED!
Imported ER70 wire
0.8 (5kg) D-200 - 80,000 rub;
0.8 (15kg) D-300 - 75000rub;
1.0 (5kg) D-200 - 75,000 rub;
1.0 (15kg) D-300 - 72000 rub;
1.2 (5kg) D-200 - 72000;
1.2 (15kg) D-300 - 70,000 rub.
NEW PRICE -> here are
gate valves, faucets, valves, radiators, couplings, etc.
VR1 wire for reinforced concrete structures is used to strengthen building structures - both made of reinforced concrete and all-steel type, VR-1 is also used to strengthen road surfaces. GOST used: 7348-81, 6727-80. Steel grades for VR wire: VR 1, VR 2, VR 3, VR 4. VR1 wire is made by cold-drawn broaching from steel wire rod and has the shape of a thread with a round cross-section; during the rolling process it is obtained corrugated surface. Where is VR-1 wire used?The main area of application of VR1 wire:
Additionally, low-carbon cold-drawn wire VR 1 with a diameter of 3, 4 and 5 mm is used in the manufacture of masonry mesh, the production of roller blinds in Voronezh and as the main element of chain-link mesh. Differences from other types of wireA distinctive feature of BP wire is its corrugated surface, while the arrangement of the corrugations is dented reefs and they are located on opposite sides of the wire rod, and the other two sides are smooth. BP1 wire differs from conventional reinforcement in that the reefs on the reinforcement are convex. The pitch of the dents is equal intervals. An alternative name for BP1 wire is reinforcing wire. BP1 wire is supplied to the end consumer in coils, with a continuous cut and without tangled rows. Coils of wire weighing 20-100 kg are tied into coils. In this case, the weight of the cargo package should not exceed 1500 kg. By agreement, an increase in the weight of the cargo package is allowed.
|
Source: http://www.provoloka34.ru/provoloka/provoloka-vr-1
Weight of welded mesh, masonry mesh made of reinforcing wire GOST 6727-80
Metal mesh is one of the most popular types of steel products.
They are used in many areas of our lives - from country house construction to the food and chemical industries. Steel mesh is made from steel wire with a thickness of 6 to 20 mm (regular, galvanized or stainless) and is divided into types according to the production method:
- welded
- woven
- wicker (aka “chain-link”)
Welded mesh (often also called reinforcing mesh) is made by spot welding fairly thick wire or reinforcement. They are distinguished by great rigidity and strength - therefore, their reinforced mesh is most often used for reinforcing monolithic reinforced concrete structures and laying brick walls.
But welded mesh can also be used in the construction of various barriers, fences and road surfaces.
The main advantage of welded mesh is, as already mentioned, strength and the ability to be manufactured strictly “to order” - they can be produced with a strictly specified cell size and from rods of different thicknesses.
Such meshes are produced on fairly simple machines from low-carbon wire and are therefore exceptionally cheap.
Weight of wire reinforcement GOST 6727-80
Reinforcing wire GOST 6727-80, depending on the mechanical properties, is divided into ordinary and high-strength, and according to the shape of the surface - into smooth and periodic profile.
Ordinary reinforcing wire (GOST 6727-80*) is made from low-carbon steel. Wire diameter d = 3, 4 and 5 mm. The entire assortment can be of two classes: BI - smooth; VR-1 - periodic profile. Reinforcing wire welds well, which makes it possible to use it as part of reinforcing products (reinforcement mesh).
The periodic profile BP-I is formed by dents diametrically located on its surface. The size of the reefs (dents) depends on the diameter of the wire. The dent depth h is 0.150.25 mm, the pitch s is 23 mm, and the protrusion length b is 0.61 mm.
Welded meshes and frames are made from BP-I class wire, which are used as non-prestressed working reinforcement; only structural reinforcement is made from smooth BI profile. Cold-drawn wire, double-sided periodic profile, is made of low-carbon steel grades St 1-3 ps, kp with a carbon content of no more than 0.22%.
Table. Weight of a linear meter of wire VR-1 GOST 6727-80 (linear density) Nominal diameter d, mm Weight of a meter of wire, kg/m, no more| 3,0 | 0,052 |
| 4,0 | 0,092 |
| 5,0 | 0,144 |
How to use the steel wire specific gravity table? For example, we need to determine the weight of a wire 100 meters long with a diameter of 3 mm. To carry out the calculation, you need to multiply the specific gravity (density) by the amount of linear meters, i.e. the formula will take the form 0.052x100 = 5.2 kg.
Or vice versa, the weight of a coil of 4mm wire is 10 kg, then we determine the length of linear meters by dividing the mass of the coil by the linear density: 10/0.052 = 192.3 meters.
To calculate the weight and length of wire of small diameters and large lengths (for example, tying wire 0.8 mm, 1.2 mm, 2.2 mm in coils for tying reinforcement), you can use the table below.
| diameter d, mm | weight 1 km, | length 1 ton, | diameter d, mm | weight 1 km, | length 1 ton, |
| kg | km | kg/km | km/ton | ||
| 0,2 | 0,247 | 4048,583 | 1,6 | 15,303 | 65,347 |
| 0,3 | 0,555 | 1801,802 | 1,8 | 20,000 | 50,000 |
| 0,4 | 0,987 | 1013,171 | 2,0 | 24,693 | 40,497 |
| 0,5 | 1,544 | 647,668 | 2,5 | 33,582 | 29,778 |
| 0,6 | 2,222 | 450,045 | 3,0 | 55,559 | 17,999 |
| 0,7 | 3,025 | 330,633 | 3,5 | 75,621 | 13,224 |
| 0,8 | 3,950 | 253,165 | 4,0 | 98,771 | 10,124 |
| 0,9 | 5,000 | 200,000 | 4,5 | 125,006 | 8,000 |
| 1,0 | 6,173 | 161,996 | 5,0 | 154,329 | 6,480 |
| 1,2 | 8,888 | 112,511 | 6,0 | 222,234 | 4,500 |
| 1,4 | 12,099 | 82,651 |
The symbol of the wire includes its nominal diameter in mm, reinforcement class and standard number, for example: wire 5 Вр-l GOST 6727-80. The nominal diameter of a periodic profile corresponds to its diameter before profiling.
Weight of 1 m2 mesh: reinforcement, masonry, road
The need to determine the weight of the mesh arises when purchasing building materials from a construction company and choosing the carrying capacity of vehicles required for transportation. The actual weight is not regulated in any way and depends on the type of wire used plus the size of the webs - the larger their dimensions and the thickness of the wire, the greater the weight of the mesh.
The masonry mesh according to GOST has its own specific size, established by the model. The width of the cells of the construction grid also plays an important role. These dimensions depend on the original purpose of the mesh and the length of the entire roll. Standard cards have a certain size: masonry grids 0.
25x2, 0.38x2, 0.5x2 and 0.64x 2 meters. The mesh for reinforcement is much larger: 2x3 and 2x6 meters. The diameter of the mesh according to GOST reaches six millimeters, the length is up to six meters, and the width is up to two meters. These indicators may differ, but not dramatically, without significant deviations in the parameters.
Let us indicate, for example, some parameters and standard sizes of masonry mesh cells made of different reinforcing wires: • 3Вр1, weight 1 m² - 2.21 kg, cell size - 50x50 mm (fine mesh); • 3Вр1, weight 1 m² - 0.99 kg, cell size - 100×100 mm; • 3Вр1, weight 1 m² - 0.72 kg, cage size - 150×150 mm; • 4Вр1, weight 1 m² - 3.62 kg, cage size - 50x50 mm; • 4Вр1, weight 1 m² - 2.02 kg, cell size -100×100 mm;
• 4Вр1, weight 1 m² - 1.24 kg, cell size -150×150 mm.
The size of the mesh cells according to GOST, depending on its overall size, can be 50, 100, 150, 200 millimeters: 50x50x2, 50x50x3, 50x50x5, 100x100x3, 100x100x4, 100x100x5, 100x100x6, 150x150x3 , 150x150x4, 150x150x5, 150x150x6, 200x200x4, 200x200x5 , 200x200x6.
To determine the theoretical weight of the reinforcing mesh, you can use ready-made tables or you can calculate it manually using the formula. To do this, calculate the weight of one reinforcement bar 1 m long and multiply by the number of bars per square meter. The number of rods per unit area is inversely proportional to the size of the mesh cell in the roll. The smaller the cell size for a given wire diameter, the greater the weight of the mesh roll per linear meter.
By multiplying the mesh dimensions (length by width) of the roll and the theoretical weight of 1 square meter, you can determine the actual weight of the entire roll. It should not differ by more than ±5% from the theoretical one. Calculating the weight of reinforcement mesh is not a complicated procedure, and there are automatic tools for this, such as a mesh weight calculator.
We will tabulate all the calculated values obtained for the mass of the mesh with cell dimensions AxA = 50x50, 100x100, 150x150, 200x200 made of reinforcing wire 3Вр1, 4Вр1, 5Вр1 with and without galvanized coating.
| Welded mesh weight in cards | |||
| Cell size, mm / Reinforcement diameter, mm | Map size, m | Weight 1m2 black, kg | Weight of 1m2 galvanized, kg |
| 50x50x3 | 2x3 | 2,000 | 2,3 |
| 50x50x4 | 2x3 | 3,600 | 3,8 |
| 50x50x5 | 0.5x2 | 5,650 | 5,8 |
| 100x100x3 | 0.5x2 | 1,000 | 1,2 |
| 100x100x4 | 2x6 | 1,800 | 1,9 |
| 100x100x5 | 2x6 | 2,800 | — |
| 100x100x6 | 2x3 | 3,472 | — |
| 150x150x3 | 2x6 | 0,590 | — |
| 150x150x4 | 2x6 | 0,800 | — |
| 150x150x5 | 2x6 | 1,900 | — |
| 150x150x6 | 2x6 | 2,475 | — |
| 200x200x4 | 2x6 | 0,800 | — |
| 200x200x5 | 2x6 | 1,450 | — |
| 200x200x6 | 2x6 | 1,905 | — |
The approximate weight of one masonry mesh card (armoured belt) depends on the dimensional parameters, which may vary slightly among different Ukrainian manufacturers depending on local market needs, which is allowed by technical conditions.
Each mesh manufacturer has its own range of mesh sizes and wire thicknesses within the GOST standards.
Welded mesh is used for reinforcing reinforced concrete elements, strengthening brickwork, manufacturing technological structures in industry and agriculture, and road construction in Kyiv.
All types of mesh are welded using resistance spot welding, which is based on the fact that a strong and long-lasting connection occurs when a large electric current passes through tightly compressed wire rods.
In this case, the metal of the wire melts, and then, after stopping the current supply, it cools and crystallizes.
The process of welding wire, as a physical process, is described by the formula Q=I2*R*t, where Q is the amount of heat - depends on the magnitude of the electric current passing through the cross-shaped joints of the rods, R - the resistance of the metal being welded at the welding point, t - the time of passage of the current .
Important to note:1. When welding reinforcing mesh, current density is of great importance, which depends on the size of the welding point of the reinforcement. If the requirements for the strength of the welded mesh are high, then the contact patch must be large enough, the current must be increased in order to maintain the required density and strict welding mode of the reinforcing wire mesh.
Otherwise, for the necessary heating of the metal, it will be necessary to increase the time of current passage, which will lead to overheating and blackening of the joint, as well as a large splash of molten metal.2. The contact patch of the metal wire is of great importance.
Increasing it on the one hand reduces the resistance, and on the other hand the specific pressure on the rods decreases and the resistance increases. All these changes affect the heating at the welding point of the wire mesh.3. The compression force of two reinforcement bars is of great importance, because the formation of the core during steel crystallization depends on it.
Selecting parameters for welding wire mesh is the key to producing quality products!
Source: https://sbk.ltd.ua/ru/sortament-ves-metalloprokata/231-ves-setki-svarnoj-kladochnoj-iz-armaturnoj-provoloki-gost-6727-80.html
Wire for reinforcement VR 2
Carbon steel wire for reinforcing prestressed reinforced concrete structures (GOST 7348-81). Purpose: cold-drawn reinforcement wire BP 2 is intended for reinforcing prestressed reinforced concrete structures.Symbol: Wire with a diameter of 5.0 mm, strength class 1400, round, stabilized. accuracy group 1, Wire 5 V1400-R1 GOST 7348-81. Description: The wire is made of steel grades 75, 80. The wire is made round - B, tempered under tension (stabilized) - P, with manufacturing accuracy of 1, 2 groups. Wire diameter vr 2 and maximum deviationsNominal diameter, mm Round and periodic steel wire Maximum deviations, mm Group 1 Group 2
Mechanical properties of wireNominal diameter, mm Strength class, N/mm2 Nominal tensile strength, N/mm2 Breaking force, N (kgf) Force P0.2, N(kgf) Relative, elongation after break, δ100,% Number of bends of steel wire with a roll diameter of 30 mm no less
Packaging: Wire for reinforcement BP 2 is supplied in coils weighing up to 15,000 kg with an internal diameter of 1400 mm or in rods of measured length up to 7.0 (packs weighing up to 1000 kg). |
Source: http://mmk-metiz.ru/product/provoloka-iz-uglerodistoy-stali-dlya-armirovaniya-predvaritelno-napryazhennykh-zhelezobetonnykh-konstruktsiy-vr-2-gost-7348-81/
Grid VR 3, 4, 5 - prices and characteristics
Mesh VR 3, 4, 5 is a metal product in the shape of a lattice, which is made from special reinforcing wire BP1 by welding. Its distinctive feature is the presence of special dents on the surface of strictly regulated shapes and sizes. The numbers 3, 4, 5 characterize the diameter of the wire in mm from which the mesh is made.
Welded mesh from the BP1 profile (GOST 6727-80) is manufactured mainly for construction needs. The most popular cell sizes of these products are square from 50x50 to 200x200 mm.
Theoretical weight of 1 m2 of VR-1 mesh
Mesh size / Wire diameter D = 3 mm D = 4 mm D = 5 mm| 50x50 | 2.22 kg | 3.86 kg | 5.92 kg |
| 100x50 | 1.66 kg | 2.96 kg | — |
| 100x100 | 1.13 kg | 2.00 kg | 3.10 kg |
| 150x150 | 0.77 kg | 1.35 kg | 2.10 kg |
| 200x200 | 0.58 kg | 1.02 kg | 1.59 kg |
| Prices in the APEX METAL price list* | open | open | open |
* You can find out the current prices depending on the volume if you follow the link to the Catalog page and click on the name of the selected product or the “Buy” button.
Characteristics of the VR 3, 4, 5 grid
Let's compare the characteristics of welded mesh 100x100 made of rolled steel 3 - 5 mm thick with a periodic profile.
Characteristics VR grid 3 VR grid 4 VR grid 5| Wire breaking force | 39 rH | 71 rH | 106 rH |
| Force corresponding to the yield point | 35 rH | 62 rH | 97 rH |
| Minimum number of bends | 4 | 4 | 4 |
| Relative extension | not less than 2% | not less than 2.5% | not less than 3% |
You can notice that a mesh with a cell size of 100x100 made of different wires with increasing diameter can withstand a breaking force that is as many times greater (approximately) as its mass per square meter is.
Technical requirements for VR grids
Requirement Value for welded mesh BP with a diameter of 3, 4 or 5 mm| Accuracy requirements | Welded mesh in accordance with the provisions of GOST 8478-81 can be manufactured with increased and normal accuracy |
| Straightness of rods | The permissible deviation from the straightness of the transverse rods is no more than 4% of the cell size for products of increased accuracy and 5% for products of normal accuracy. |
| Distance deviation between longitudinal bars | At the edges of the mesh - within ±5 mm and ±10 mm for products of increased and normal accuracy, respectively. The exact same values are for maximum deviations of grid cell sizes. |
| Welding Features | Welding at the point of contact of the rods is carried out using a spot method, and the cross-shaped welded joint must comply with GOST 14098. |
| Welding quality | All intersections of BP wire rods must be welded. For high-precision meshes, it is possible to have no more than 2 unwelded intersections per 1 meter length, and for normal accuracy - no more than 4. |
| Mesh strength VR | The tensile strength of the rod at the welding points must comply with GOST 10922 |
Woven mesh (chain-link)
Price list for woven mesh (chain-link) with cells from 6x6 mm to 55x55 mm, thickness from 1 mm to 3 mm
Plaster mesh
Prices for woven (plaster) mesh with cells from 0.4x0.4 mm to 20x20 mm, thickness from 0.25 mm to 1.6 mm
Source: https://apex-metal.ru/articles/setka_vr_3_4_5/
Weight of steel wire: smooth V-1 and corrugated VR-1
Metal wire is a universal material. It is used in everything from cables to barbed mesh to protect fences. To work, you need to know the exact weight of the steel wire. The creation standards are complied with GOST 3282-74. But surface standards may deviate slightly from GOST standards - dents, rippling or shallow scratches are allowed.
The photo shows steel wire.
Steel wire weight 1 meter
This product is not replaceable for industry; it is used everywhere. In general, wire is rolled metal in the form of a length of thread or cord. Often the cross-section is round, but it can be oval, square, trapezoidal or hexagonal. The diameter can range from a fraction of a millimeter to several centimeters.
As mentioned above, in order to accurately carry out your work and not purchase excess material, you need to know the weight of the steel wire. Below is a table showing all the diameters of the steel product. There will also be a cell in which you can find out how many meters are in 1 ton of wire.
The grade of steel for the manufacture of this product is determined by what the VR-1 wire is intended for. For example, steel 08kp, St10, St10ps is used for knitting wire in accordance with GOST 3282-74.
Table for calculating the theoretical weight of metal (knitting) wire V-1 GOST 3282-74
| Wire diameter, mm | Weight 1 mp, kg | Number of linear meters in 1 ton | Wire diameter, mm | Weight 1 mp, kg | Number of linear meters in 1 ton |
| 0,8 | 0,0395 | 25 343 | 3 | 0,0555 | 18 022 |
| 1 | 0,0062 | 162 195 | 3,2 | 0,0631 | 15 840 |
| 1,1 | 0,0075 | 134 046 | 3,5 | 0,0755 | 13 240 |
| 1,2 | 0,0089 | 112 637 | 3,6 | 0,0799 | 12 515 |
| 1,3 | 0,0104 | 95 979 | 4 | 0,0986 | 10 137 |
| 1,4 | 0,0121 | 82 754 | 4,5 | 0,1249 | 8 010 |
| 1,6 | 0,0158 | 63 359 | 5 | 0,1541 | 6 488 |
| 1,8 | 0,0200 | 50 060 | 5,5 | 0,1865 | 5 362 |
| 2 | 0,0247 | 40 548 | 5,6 | 0,1934 | 5 172 |
| 2,2 | 0,0030 | 335 121 | 6 | 0,2220 | 4 506 |
| 2,5 | 0,0039 | 259 511 | 6,3 | 0,2447 | 4 087 |
| 2,8 | 0,0048 | 206 881 | 7 | 0,3021 | 3 310 |
Source: https://DomStrouSam.ru/ves-stalnoy-provoloki-gladkoy-v-1-i-riflenoy-vr-1/
Weight of fittings with a diameter of 5 mm
Steel wire with low carbon content, the use of which is practically unlimited, manufactured in accordance with the requirements of GOST 6727-80, is one of the most common types of hardware. These products are widely used in various industries. Such wire is produced with a nominal diameter of 3, 4, 5 mm.
The wire has a double-sided periodic profile, made of steel grade St 1 3 kp, ps. carbon should not exceed 0.22%. According to the requirements, there should be no holes, cracks, or sunsets on the entire surface of the wire. Small scratches and marks, as well as a slight coating of rust, are allowed.
Wire marking is done using an alphanumeric index:
Wire 4 vr 1 GOST GOST6727-80, where:
The weight of a linear meter of wire, depending on the diameter, has the following indicators:
- 3.0 mm (cross section 7.07 mm) – 0.052 kg;
- 4.0 mm (cross section 12.57 mm) – 0.092 kg;
- 5.0 mm (cross section 19.63 mm) – 0.144 kg
Low-carbon steel wire GOST 6727-80, the quality characteristics of which are in great demand, is most often used to create reinforcement frames and masonry reinforcing mesh during the construction of foundations of buildings and structures, and floors.
Very often, reinforcing mesh made from wire by spot welding is used to strengthen walls made of brick and other wall materials. Meshes made from such wire belong to the category of light meshes.
Widely used as reinforcement in the production of reinforced concrete products.
Wire is shipped to consumers in coils weighing from 20 to 100 kg and from 500 to 1500 kg. Each coil of wire weighing up to 100 kg is tied in at least three places, and coils weighing up to 1500 kg in four places. Each skein, regardless of length, must consist of one solid piece, the ends of which must be easily found. At the request of consumers, coils can weigh more than 1500 kg.
According to GOST 6727-80, the weight of one coil of wire should not exceed 1500 kg. Each skein has a label containing the following information:
- trademark or name of the manufacturer;
- wire grade;
- production batch number;
- technical control mark (mark).
Low-carbon wire GOST 6727-80 is stored in accordance with GOST 15150 (condition 5).
Site map Knitting wire Galvanized welded mesh for cages Services for rewinding wire into small skeins
Orel, Razdolnaya st., 105 (4862) 33-74-66; (4862) 48-58-05 E-mail: [email protected] Skype: metizniki
LLC Company Promalyans 2008- All information is protected. Copying materials is prohibited.
Welded reinforcement mesh
Welded mesh has gained wide popularity and application in construction, industry, and agriculture. Welded mesh is easy to fasten and has a low specific gravity. A distinctive feature of galvanized welded mesh is its resistance to environmental influences and a longer service life compared to its non-galvanized counterpart. Products and structures using welded mesh are affordable, easy to install, and safe to use.
The main advantages of using welded mesh .
Increased work productivity by 12 times;
In the production of welded mesh, longitudinal and transverse rods of various diameters can be used;
In the welded mesh design, the warp and weft wires are welded at the crossing points.
Welded mesh is characterized by the size of the clear side of the cell and the diameter of the wire. The size of the clear side of the cell is taken to be the distance between adjacent warp wires or adjacent weft wires. Clear mesh size, mm – from 16.0 to 48.0. Wire diameter or square side, mm - from 2.0 to 3.0.
Reinforcing mesh
Source: https://armaturasila.ru/ves-armatury/ves-armatury-diametrom-5-mm.html
GOST 6727-80 cold-drawn low-carbon steel wire for reinforcement of reinforced concrete structures. technical specifications (as amended no. 1-4), GOST dated May 15, 1980 No. 6727-80
GOST 6727-80Group B71
MKS 77.140.65
OKP 12 1400
Date of introduction 1983-01-01
1. DEVELOPED AND INTRODUCED by the USSR Ministry of Ferrous Metallurgy
DEVELOPERS
E.M.Kireev, K.G.Zalyalyutdinov, Kh.N.Belalov, N.A.Galkina, T.A.Korshunova, K.V.Mikhailov, V.I.Bondarenko, V.M.Skubko
2. APPROVED AND ENTERED INTO EFFECT by Resolution of the USSR State Committee on Standards dated 05.15.80 N 2108
3. INSTEAD GOST 6727-53
4. REFERENCE REGULATIVE AND TECHNICAL DOCUMENTS
5. The validity period was lifted according to Protocol 2-93 of the Interstate Council for Standardization, Metrology and Certification (IUS 2-93)
6. EDITION (May 2003) with Amendments No. 1, 2, 3, 4, approved in December 1984, June 1987, October 1988, February 1990 (IUS 3-85, 10-87 , 1-89, 5-90)
Reprint (as of April 2008)
This standard applies to cold-drawn low-carbon steel wire of periodic profile of class VR-1 for reinforcement of reinforced concrete structures.
(Changed edition, Amendment No. 2, 3).
1. MAIN PARAMETERS AND DIMENSIONS
1.1. (Deleted, Amendment No. 3).
1.2. The main parameters and dimensions of the wire must correspond to those indicated in Table 1.
Wire size designations are shown in the drawing.
Table 1
mm
| Nominal wire diameter | Nominal size | Maximum deviations per size | Dent depth | Limit deviations to dent depth | Nominal pitch of dents | Maximum deviations by dent pitch | Length of projection | Maximum deviations along the protrusion length |
| 3,0 | 3,0 | +0,03 -0,09 | 0,15 | +0,05-0,02 | 2,0 | ±0,2 | 0,6 | ±0,2 |
| 4,0 | 4,0 | +0,04-0,12 | 0,20 | 2,5 | 0,8 | |||
| 5,0 | 5,0 | +0,05 -0,15 | 0,25 | 3,0 | 1,0 |
Note. The nominal pitch of the dents and the radius of the interface between the surface of the dents and the protrusions are reference values for the design of a profiling tool and are not checked on the wire.
(Changed edition, Amendment No. 2, 3).
1.3. The radius of the interface between the surface of the dents and the protrusions for wire of all diameters should be equal to (2.5 ± 0.5) mm.
A relative displacement of opposite dents of up to 0.5 and their location along the helical line of the wire axis is allowed.
(Changed edition, Amendment No. 2).
1.4. The difference in size must not exceed the size tolerance range.
An example of a symbol for wire with a nominal diameter of 3.0 mm:
Wire 3 VR-1 GOST 6727-80.
(Changed edition, Amendment No. 3).
2. TECHNICAL REQUIREMENTS
2.1. The wire must be manufactured in accordance with the requirements of this standard according to technological regulations approved in the prescribed manner.
The wire is made from wire rod according to OST 14-15-193.
(Changed edition, Amendment No. 1, 2).
2.2. The mechanical properties of the wire must correspond to those indicated in Table 2.
table 2
| Nominal wire diameter, mm | Breaking force, gN (kgf) | Force corresponding to the conditional yield strength, gN (kgf) | Number of bends | Relative extension , % |
| no less | ||||
| 3,0 | 39(400) | 35(355) | 4 | 2,0 |
| 4,0 | 71(720) | 62(630) | 2,5 | |
| 5,0 | 106(1085) | 97(985) | 3,0 |
(Changed edition, Amendment No. 1, 3).
2.3. There should be no cracks, caps, sunsets, or shells on the surface of the wire.
Risks and scratches with a depth of no more than half the maximum deviations for size and rust are allowed.
(Changed edition, Amendment No. 3).
2.4. The wire is produced in coils weighing 500-1500 kg. It is allowed to produce wire in coils weighing 20-100 kg. Each skein should consist of one piece of wire. The wire should be rolled into skeins in untangled rows.
(Changed edition, Amendment No. 2).
2.5. The linear density of the wire must correspond to that indicated in Table 3.
Table 3
| Nominal wire diameter, mm | Linear density, kg, no more |
| 3,0 | 0,052 |
| 4,0 | 0,092 |
| 5,0 | 0,144 |
The calculated cross-sectional area and theoretical linear density of the wire are given in Appendix 2.
(Changed edition, Amendment No. 2, 3).
3. ACCEPTANCE RULES
3.1. Wire is accepted in batches.
The batch must consist of wire of the same diameter, drawn up in one quality document, which should indicate:
— trademark or name and trademark of the manufacturer;
— symbol of the wire;
— test results;
- number of skeins;
— batch number;
— net weight of the batch;
— image of the state Quality Mark for wire of the highest quality category.
(Changed edition, Amendment No. 1, 2, 3).
3.2. The size, size difference and surface quality of the wire are checked on each skein.
(Changed edition, Amendment No. 3).
3.3. To check the mechanical properties of the wire and the parameters of the wire profile, 3% of the coils must be selected from the batch, but not less than 5 coils.
(Changed edition, Amendment No. 2).
3.4. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double sample. The results of the re-inspection are applied to the entire batch.
4. TEST METHODS
4.1. For each type of test, one sample is taken from one end of the skein.
4.2. The quality of the wire surface is controlled by the naked eye.
4.3. Dimensions and wires are measured with a micrometer according to GOST 6507.
The magnitude of the difference in size is determined as the arithmetic mean of three measurements taken over a section 1 m long.
(Changed edition, Amendment No. 2, 3).
4.4. The wire profile parameters are determined as the arithmetic mean of three measurements taken over a section 1 m long on each side.
The depth of the dents is measured with a micrometer in accordance with GOST 6507, equipped with a special heel (Appendix 1).
The length of the protrusion is measured by a reading microscope MPB-2, manufactured according to technical documentation.
In case of disagreement in the measurement of wire profile parameters, control is carried out according to the linear density of the wire (Table 3).
The linear density of the wire is determined as the quotient of the mass of two samples 1 m long, weighed with an error of up to 0.001 kg, divided by their length, measured with an error of up to 0.001 m.
(Changed edition, Amendment No. 2, 3).
4.5. Wire tensile testing is carried out according to GOST 12004.
4.6. Bend testing of wire is carried out in accordance with GOST 1579. Wire with a diameter of 3.0 and 4.0 mm is tested on rollers with a diameter of 20 mm, and with a diameter of 5.0 mm - on rollers with a diameter of 30 mm.
When testing a wire, the sample is clamped so that the dents face the jaws of the device.
4.5, 4.6. (Changed edition, Amendment No. 2).
4.7. The depth of marks and scratches is determined by removing them by sanding, followed by comparative measurements in cleaned and uncleaned areas.
(Changed edition, Amendment No. 2, 3).
5. PACKAGING, LABELING, TRANSPORTATION AND STORAGE
5.1. Each skein weighing 500-1500 kg must be evenly tied around the circumference in at least four places, and a skein weighing 20-100 kg - in at least three places.
At the consumer's request, a skein weighing 500-1500 kg must have intermediate knittings located inside the skein.
Wire rod according to OST 14-15-193 or heat-treated wire according to regulatory and technical documentation is used as binding materials.
The ends of the skein should be neatly laid out and easily found.
(Changed edition, Amendment No. 2, 4).
5.1a. Rolls of wire weighing 20-100 kg are tied into coils.
The weight of the cargo package should not exceed 1500 kg. By agreement between the manufacturer and the consumer, an increase in the weight of the cargo package is allowed.
Cargo packages are formed into transport packages in accordance with GOST 24597 and GOST 21650.
(Introduced additionally, Amendment No. 2).
5.2. Each skein (coil) must have a label firmly attached to it, indicating:
— trademark or name and trademark of the manufacturer;
— symbol of the wire;
— batch number;
— technical control mark;
— image of the state Quality Mark for wire of the highest quality category.
(Changed edition, Amendment No. 1, 2).
5.3. Wire is transported by all types of transport in accordance with the rules for the carriage of goods in force for this type of transport.
The placement and securing of cargo in vehicles transported by rail must comply with the technical conditions for loading and securing cargo approved by the USSR Ministry of Railways.
Transportation by rail is carried out by wagonload and low-tonnage or small shipments.
It is allowed to transport wire in universal containers in accordance with GOST 15102, GOST 20435, GOST 22225.
5.4. Wire storage is in accordance with the conditions of 5 GOST 15150.
5.3, 5.4. (Changed edition, Amendment No. 2).
5.5. Transportation of wire sent to the Far North and equivalent areas is carried out in accordance with GOST 15846.
(Changed edition, Amendment No. 3).
5.6. Transport marking - according to GOST 14192.
(Introduced additionally, Amendment No. 2).
Appendix 1 (mandatory). special heel for micrometer type MK according to GOST 6507 for measuring the depth of dents
APPENDIX 1 Mandatory
Material: steel ШХ15, У10А, У12А. Hardness - HRC48-50.
Appendix 2 (for reference). calculated cross-sectional area and theoretical linear density of wire
APPENDIX 2 Information
| Nominal wire diameter, mm | Design cross-sectional area, mm | Theoretical linear density, kg* |
| 3,0 | 7,07 | 0,052 |
| 4,0 | 12,57 | 0,092 |
| 5,0 | 19,63 | 0,144 |
________________
* Letter of Rosstandart dated December 22, 2017 N 2122-OG/03 explains the following: in Appendix 2, namely in the header of the table, there was a typo - Theoretical linear density is measured in kg/m. — Note from the database manufacturer.
APPENDIX 2. (Changed edition, Amendment No. 2, 3).
The electronic text of the document was prepared by Codex JSC and verified against: official publication
M.: Standartinform, 2008
Source: http://docs.cntd.ru/document/464623678
Mesh VR-1 durable material for strengthening concrete
In the construction industry there are concrete structures that need to be strengthened with special reinforcing materials. VR-1 mesh is the most popular building material. This product has high strength and reliability, which ensures a long service life of the structure.
In this article we will take a detailed look at what it is, where it is used, types and sizes of VR mesh. Let's consider the main classifications and the method of calculating the required amount of material for strengthening.
General idea of reinforcing mesh
Reinforcing mesh is a metal product made from steel wire of various diameters. The wire is cut into pieces of a certain size and welded strictly perpendicular to each other.
Depending on the class and purpose of the finished product, different wires can be used for manufacturing.
This can be cold-rolled mesh VR-1 made of special steel with a low carbon content in the composition or hot-rolled from steel grade A-III or A-I.
You need to pay attention to the designations in the form: VR-2 grid, VR-3 grid, etc. This is not a type of wire, but a corresponding strength class. The higher the number, the larger the diameter of the rods, and, accordingly, the higher the strength class. The rods can be either smooth or with a corrugated surface. A mesh of wire with corrugations will provide a stronger connection to the concrete mixture.
Products are manufactured at specialized enterprises that have the necessary machines and additional equipment for welding. Finished products with a small diameter and cell size are rolled into rolls. Thicker products are sold in cards of a certain size. Each kart must have documentation and appropriate quality certificates.
All characteristics and geometric dimensions of the product must comply with GOST:
• Standard cell sizes from 50 by 50 millimeters to 200 by 200 millimeters;
• One linear meter of mesh made from the thinnest wire should weigh approximately 0.5 kilograms, and from the thickest wire – 3.7 kilograms. A slight deviation is allowed (50-80 grams); • The width of the card or roll is no more than 150 millimeters, and the length of one sheet is 200 millimeters.
As you already understand, the main material for making meshes is VR-1 metal wire. It is widely used in both the construction and industrial sectors.
It can be made from steel of various grades, as well as with the addition of impurities of other metals (zinc, aluminum and others).
6 main classification groups
GOST, on the basis of which reinforcing mesh is produced for strengthening concrete structures, specifies seven main classification groups. Let's look at each of them in more detail.
- The first group distributes products according to the main section of the rod: • Light type. This category includes products made from rods no more than 5 millimeters thick. The main reinforcement step for concrete structures must correspond to the basic values (10-30 centimeters). If necessary, it can be changed up or down, but there must be a technical and economic justification for this;
• Heavy type. Here, rods with a thickness of 12 to 40 millimeters are used for production. If the reinforcement has previously undergone a heat treatment procedure for strengthening, then rods with a diameter of 10 mm or more can be used.
- Second group. Distribution relative to the position of distribution and main operating fittings. There are only two varieties: • Working rods can be positioned both lengthwise and transversely, and distribution type rods must be strictly perpendicular to the mesh itself;
• The working rods are located lengthwise and crosswise at once.
- The third group for classification is carried out according to technical characteristics: • First class. These are heavy structures with large wire thickness (BP-6 mesh). The working rods are arranged longitudinally and have a larger cross-section than that of the distribution elements; • Second class. It is also considered heavy with a fairly large thickness of rods. The working fittings are located lengthwise and crosswise; • Third class. Another type of heavy mesh, only here the working rods are located across; • Fourth grade. These products are already considered lightweight. They are made from fairly thin wire and have small cell sizes;
• Fifth grade. Lightweight type, where the cross rods are installed with a slight offset.
- • In rolls.
If the mesh is light with a wire thickness of less than 5 millimeters, then it is rolled into rolls of a certain length. Rolls are very convenient for transportation, and they are also easy to cut and undergo other mechanical processing; • In cards. If the thickness of the wire from which the mesh is made is more than 5 millimeters, then twisting it into a roll is already problematic. Therefore, it is supplied in flat cards of appropriate geometric dimensions. - Fifth group for main purpose: • Masonry mesh. It has large thickness of rods (6 mm or more). Its main purpose is to strengthen brick or block masonry, as well as strengthen the foundation of houses and industrial buildings. It is supplied mainly in cards with different widths. To reinforce walls made of bricks or blocks, the width should be 380 - 640 millimeters. And for partitions, the width should be about 110-250 mm. In order to make it convenient to reinforce walls and partitions, the cards should be no more than two meters long; • Reinforcing mesh. It is made of wire with a thickness of 3 to 6 mm. The shape of the cells can be either rectangular or square. For regular mesh, smooth rods are used, while for road products, corrugated and thicker rods are used;
• Rabitz. These are special products that are made by twisting wire of various diameters (from 1.5 to 5.5 millimeters). The main material is black or galvanized wire. The main purpose of these products is the construction of fences, enclosures and cages for animals. Widely used for economic purposes.
- The sixth classification group is based on the accuracy class of the welded joint: • Normal accuracy. Here, too high demands are not placed on the quality of welds;
• Increased accuracy. In this case, the welds are stronger and of higher quality.
Recommended reading:
What is a mesh for floor slabs? 6 main advantages of use
Metal mesh for fencing: main types and correct installation technology
Characteristics and advantages of the VR-1 mesh
The main elements are welded strictly at an angle of 90 degrees on special equipment using a resistance welding machine. The shape of the cells in most cases is square. The cell has typical side dimensions of 50 (50 by 50, 100 by 100, 150 by 150, etc.). Each manufacturer may offer different cell sizes and rod thicknesses, but all this will be within the appropriate GOST. Production according to individual sizes is allowed.
Products can be untreated or coated with zinc to protect against corrosion. The thickness of the protective layer may vary. The larger it is, the higher the anti-corrosion properties and service life will be. Galvanized products can be used in conditions with high humidity. The VR-1 mesh with a protective coating costs several times more than the usual one. Therefore, if your budget is limited, then it is worth purchasing more budget options.
Construction mesh VR-1 for strengthening concrete structures has the following advantages: • Versatility.
The material can be used for various construction and industrial purposes; • High quality indicators (strength, resistance to mechanical stress and other indicators); • Long service life.
When used under normal conditions, the material can last for several decades;
• Economic benefits. Compared to other building reinforcement materials, mesh is relatively inexpensive.
Where is the VR grid used?
This product is used in various fields of industry, but it is most widely used in the construction industry. The mesh is mainly used to strengthen reinforced concrete structures for various purposes, to reinforce brick and block masonry walls and partitions of a building, as well as for a number of facing and facade works.
Masonry-type products are designed to strengthen walls. As a result, the possibility of cracks and other deformations is completely eliminated. It is also used in the reconstruction of old buildings and structures. Welded mesh is used to reinforce various reinforced concrete slabs, pillars and other elements. With its help, the foundation, floors are reinforced, and floor screed is also performed.
The material can be used to make fences for country houses and industrial facilities, enclosures and cages for farm animals. To strengthen asphalt during road work, a heavy mesh with thick rods and large cell sizes (up to 250 millimeters) is used.
How is the VR-1 grid calculated?
Before starting construction work, it is necessary to correctly perform all the necessary calculations. It will be necessary to calculate not only the required amount of material, but also its dimensions with basic indicators. Only on the basis of the data obtained can you purchase suitable products.
When choosing, you should take into account the specific location where construction work will be carried out, as well as all its features. For example, if it is necessary to carry out the procedure of reinforcing the foundation, then it is worth taking into account the perimeter of the future building and all the loads that will affect it. After this, it will be possible to calculate the thickness of the rods and the installation pitch.
One of the important parameters is the weight of the product. Based on this, the final cost is calculated. To do this, you need to find out the mass of one linear meter and multiply it by the total length of the mesh that you will use in each specific case.
To correctly perform all the necessary calculations, you must have certain technical knowledge. Therefore, it is best to entrust this procedure to experienced specialists. If the calculations are incorrect, the structures will deform over time, and the overall service life of the construction project will be significantly reduced.
Reinforcing mesh VR-1 is actively used to strengthen reinforced concrete structures and brickwork. If you want your construction projects to last for decades, then you need to choose the right quality products.
Source: http://blog.kpmtrade.ru/setka-metallicheskaya/setka-vr-1/
Wire VR 1 - characteristics according to GOST
VR-1 wire is a type of rolled steel of a periodic profile, used to create reinforced concrete structures. Technical specifications for VR-1 wire with diameters of 3, 4, 5 mm made of low-carbon steel are regulated by GOST 6727-80, for products with diameters of 3, 4, 5, 6, 7, 8 mm intended for strengthening prestressed reinforced concrete structures - GOST 7348 -81.
Technical characteristics of wire VR-1
The wire is produced by cold drawing on equipment with specially shaped rolls. They form a periodic profile, creating diametrically located dents 0.15-0.25 mm deep with a pitch of 2-3 mm. According to GOST 6727-80, products with a diameter of 3, 4, 5 are manufactured; according to technical conditions, products of intermediate diameters are produced - 2.5-4.8 mm.
Weight of 1 m of wire VR-1 according to GOST 7348-81
| Nominal diameter, mm | Weight 1 m, kg |
| 3,0 | 0,0555 |
| 4,0 | 0,0987 |
| 5,0 | 0,154 |
| 6,0 | 0,222 |
| 7,0 | 0,302 |
| 8,0 | 0,395 |
To mark metal products, an alphanumeric designation is used, for example 4 VR-1 GOST 6727-80, where:
- 4 – diameter;
- “Вр” – periodic profile;
- 1 – accuracy class.
In the designation of products manufactured in accordance with GOST, after the letters “Вр” the strength class is indicated: 1000, 1100, 1200, 1300, 1400, 1500.
Russian-made VR-1 wire is sold in coils of 20-100, 500-1500 kg, since the production of this rolled product in rods is a process that requires significant energy and labor costs. At the customer's request, the wire is cut into rods 2-4 m long, leveled, and packaged in bundles weighing up to 500 kg.
Application of wire VR-1
These metal products are most widely used for the manufacture of lightweight reinforcing mesh - flat and canned, with a wavy structure.
To improve resistance to aggressive environments, the wire is coated with a protective zinc layer and additionally with polymer compounds. To produce welded mesh, the rods are laid perpendicular to each other and connected by contact welding.
Cells can be square or rectangular. The standard card length is 2000 mm, any width.
Wire mesh VR-1 is used in:
- construction - for reinforcing concrete elements, during the construction of greenhouses and light frame buildings;
- road construction and when carrying out repair activities;
- finishing work for leveling vertical and horizontal surfaces.
Requirements for wire mesh VR-1 according to GOST 23279-85
According to GOST 23279-85, welded flat mesh is sold in bags or rolls weighing no more than three tons. The roll is tied with knitting wire in three places, the package in four. The tags accompanying the rolls or bags contain information about the manufacturer, date of manufacture, weight in tons and batch number. There must be at least two such tags. They are located on different sides of the package or roll.
Products can only be stored in dry rooms with normal temperatures. Bags and rolls are stored horizontally on pallets. Packages can be stacked in stacks, the height of which does not exceed 2 m, rolls - no more than three pieces in height.
Source: https://TreydMetall.ru/info/provoloka-bp-1-po-gost
Wire VR-1 5mm
Name: wire
: reinforcing (VR-1)
Diameter: 5 mm
Standard: GOST 6727
Product description
It is analogous to fittings. It has periodic corrugation, which allows it to be firmly fixed in concrete.
The main purpose is the reinforcement of small-sized reinforced concrete products, the production of reinforcing mesh.
VR-1 wire gives the reinforced concrete structure high rigidity and mechanical strength, avoiding cracks in the concrete layer, since the reinforcing belt made of wire rods takes on transverse tensile loads.
Product Features
For the convenience of customers, our warehouse has coils of various weights. Depending on the quantity you need, we will select the closest skein in weight from stock. If you need a coil of a strictly specific weight, please indicate it in the additional information field when adding the item to your cart. We will fulfill your order without additional payment for the unwinding service, and our manager will inform you of the deadline for its execution.
For goods sold by weight, the price in the order on the website may differ from the price in the invoice or invoice due to the deviation of the theoretical weight from the actual one.
The theoretical weight of one meter of rolled metal is established by regulatory and technical documentation, and the actual weight is always different for each batch of goods. These deviations are associated with uneven wall thickness of the product during manufacturing.
The actual weight value differs from the calculated value by up to ±10%.
The value of weight and cost non- weight units of measurement that are indicated on the website are for reference and are calculated using coefficients from the regulatory and technical documentation for the product.
The final cost of the order is calculated by the manager.
If you want to know the exact cost, wait until the manager processes your order. When processing an order, the manager receives more accurate information from the warehouse about the current actual weight of the shipment of goods.
The manager does not know when you plan to receive your order, so when you issue an invoice, he makes a calculation based on the maximum actual weight of the remaining inventory, so that you do not have a situation with a lack of money.
The final payment for the required footage of weighted goods will be made based on its actual weight.
The actual weight is determined by weighing the rolled metal on an electronic scale.
We always return all excess money transferred to the buyer at his request.
Please read the terms of cooperation
We deliver free of charge within the city:
- any order within 5 working days
- from 1 ton from 8:00 to 21:00 tomorrow
- from 3 tons from 8:00 to 17:00 tomorrow
Additional services:
- payment at the place of delivery in cash or by bank card
- unloading on site
- delivery at night and on weekends
- 50% discount on tariffs for orders less than 1 ton for delivery from 8:00 to 21:00
We are always happy to help and offer the most profitable option for receiving your order.
You can view the full list of delivery conditions in the “Delivery” section of the terms of cooperation.
- We work for you every day from 8:00 to 17:00 without a lunch break , except Saturday and Sunday, as well as public holidays
- when registering preliminary cargo preparation (this is a free service), you can receive your order after 17:00 or on a day off
- we have 2 warehouses in Omsk on both banks of the Irtysh: in the Amur at 22 Party Congress, 105 and in Stary Kirovsk, at Semirechenskaya, 99
- we can prepare the cargo in advance so that you receive it at a time convenient for you and without a queue
- if your order is completed from three or more sites, we will collect the entire order at one loading point
- We will be happy to load your order into a car, bicycle, Segway or other unsuitable transport, including covered
- we accept both cash and bank transfer
- Gazprombank and Sberbank ATMs are installed on the territory of the Ommet-Central warehouse, where you can withdraw money
- If you plan to pay for your order at the Ommet-Semirechensky warehouse, we ask you to withdraw cash in advance, because we cannot force banks to install an ATM there
- You can always return the product, provided that it remains in its salable condition, and if it is already cut, we will consider the return individually
This product is very often purchased with
Source: https://xn--80ajihiadw2acf5i.xn--p1ai/product/provoloka-vr-1-5
Scales VR-5 in Divnoye
The technical characteristics of the product may differ from those indicated on the website; please check the technical characteristics of the product at the time of purchase and payment.
All information on the site about products is for reference only and is not a public offer in accordance with paragraph 2 of Article 437 of the Civil Code of the Russian Federation. We kindly ask you to check the availability of the desired functions and characteristics when purchasing.
When ordering goods on weekdays before 15:00 and the goods are in stock, delivery is carried out the next day or on any day and time convenient for you (including Saturdays within the Moscow Ring Road).
When ordering goods on weekends and having goods in stock, delivery is carried out on Tuesday or on any day and time convenient for you (including Saturdays within the Moscow Ring Road)
Urgent delivery within 2-4 hours is carried out only if the goods are in stock and the courier is available.
Free delivery is carried out only to the cargo terminal of TC SDEK, if the client is in a city where there is no pick-up point for TC SDEK, we deliver free of charge to the nearest terminal of this company (SDEK)! The timing for this delivery is set according to the tariffs of the shopping center and at the discretion of the sender!
There is no urgent tariff or targeted delivery in the “Free Delivery” service!!!
Free delivery can only be used when ordering a cash register with a full set of services (turnkey cash register)! Under this condition, only the cash register is delivered free of charge.
If a client buys a cash register with a full set of services + other goods (scales, cash drawer, banknote counter, label printer, 10 boxes of receipt tape, etc.), then we deliver only the cash register for free; the client pays for delivery for everything else separately.
- — CDEK;
- - Business Line;
- - DPD;
- — EMS;
- — Express RU.
Terms of free delivery in Moscow and Moscow Region
Your order is delivered by courier service:
- — Grastin (up to 25 km from the Moscow Ring Road);
- — Algorithm (up to 25 km from the Moscow Ring Road);
- — CDEK (from 25 km from the Moscow Ring Road and more);
Free delivery can only be used when ordering a cash register with a full set of services (turnkey cash register)! Under this condition, only the cash register is delivered free of charge.
If a client buys a cash register with a full set of services + other goods (scales, cash drawer, banknote counter, label printer, 10 boxes of receipt tape, etc.), then we deliver only the cash register for free; the client pays for delivery for everything else separately.
Free delivery is carried out to an address in Moscow and Moscow Region (up to 25 km from the Moscow Ring Road) the next day after its registration. On the day of the planned delivery, you need to answer the courier's call; if the courier does not call, the courier has the right to reschedule delivery to the next day.
If you are located more than 25 km from the Moscow Ring Road, then delivery is carried out by TC CDEK to the delivery point of this company closest to you, according to the parameters for this direction (the terms are communicated by the logistician when placing an order for delivery).
The choice of shopping center, according to the terms of free delivery, is made at the discretion of the sender.
IMPORTANT:
Due to the seasonal increase in the number of orders, delivery times are temporarily increased (until the end of December). We apologize for the temporary inconvenience.
If the product is located in our remote warehouse, and you want to come and buy it, you need to contact the manager and arrange delivery of the product to our office. Indicate the product and quantity, contact phone number. When the goods are in our office, the manager will call you back.
If you want to arrange delivery of goods to you, then in the order indicate the product and quantity, to whom to issue documents and a contact phone number. After this, the manager will contact you to clarify the order details, date, time and exact delivery address.
If you require a maintenance contract upon delivery of the cash register, please notify the manager in advance!
Delivery is made within 1-2 days , depending on the workload of the delivery service.
Shipments to the regions are made within 1-2 days after receiving advance payment.
Payment is accepted both by bank transfer and in cash.
Payment options:
You choose the payment method yourself and indicate it in the comments when placing an order.
For non-cash payments, we issue an invoice and send it by e-mail.
Once the money is received in the bank account, we make the shipment. The goods can be received either by pickup from our warehouse, or through delivery by courier or transport company. Originals of primary accounting documents are issued.
When paying in cash , we notify you about the availability of goods in stock. You either come, pay and pick up the goods, or the courier brings it to you. Originals of primary accounting documents are issued
and a cash receipt.
When preparing documents for a legal entity and individual entrepreneur, the client must provide either a power of attorney from the buyer or affix a stamp. Otherwise, the documents are issued to a private person
and no invoice is issued.
Purchase returns
Regulations on the return or exchange of goods by individuals (Regulations drawn up in accordance with Article 26.1 (Remote method of sale)
Law of the Russian Federation “On the Protection of Consumer Rights” dated 02/07/1992
1. The buyer has the right to refuse the goods or exchange them for another product at any time before their transfer, and after the transfer of the goods - within fourteen days.
2. Returns or exchanges of goods are carried out on weekdays from 9.00 to 17.00.
3. Return or exchange of goods of proper quality is possible if its presentation, consumer properties, as well as a document confirming the fact and conditions of purchase of the specified goods (cash receipt, receipt for payment for the goods) are preserved.
4. The return or exchange of goods is made by the Seller based on the Buyer’s application for the return of goods, subject to presentation of a passport.
5. The Buyer’s absence of a document confirming the fact and conditions of purchase of the goods does not deprive him of the opportunity to refer to other evidence of the purchase of goods from the Seller.
6. The Buyer does not have the right to refuse the goods or exchange goods of appropriate quality that have individually defined properties (tinting goods, sawn long goods or furniture facades, etc.), if the specified goods can be used exclusively by the Buyer purchasing it. Not allowed changing the assortment and (or) parameters of goods supplied or manufactured specifically for the Buyer after making an advance payment.
7. If the Buyer refuses the goods he paid for, the Seller returns the amount of money no later than ten days from the date the Buyer presents the corresponding demand and returns the goods to the Seller in accordance with clause 4 of these Regulations. The refund is made to the Buyer’s bank card. Refund period after order cancellation is from 1 to 30 calendar days depending on the Bank that issued your card.
8. Return or exchange of goods of inadequate quality is carried out in accordance with the provisions of Articles 18-24 of the Law of the Russian Federation On the Protection of Consumer Rights dated 02/07/1992.
9. You can ask our employees about additional questions about returning or exchanging goods by phone, email or at the company office.
Do you have any questions?
Get a free consultation! Leave your phone number, we will call you back
and answer your questions!
Source: https://online-kassa.ru/divnoye/kupit/vesy-vr-5/
