How many kg are 1 meter of reinforcement

Reinforcement weight, weight table (weight) per 1 meter of reinforcement

When carrying out construction and installation work, calculating the mass of metal products is extremely important, since it allows you to estimate the final parameters of the structures being built and determine the cost of the material (for this, the weight of the reinforcement is taken to be 10 mm per meter).

To carry out calculations, you can use special tables that indicate the parameters of the rods and their estimated weight, as well as popular online calculators, for the use of which you need to know the exact data on the technical characteristics of rolled metal.

Knowing the exact weight of rolled materials, you can save a lot by choosing the right vehicle to transport them. If you are not sure that you can make the calculations correctly, the Regional House of Metal company will help you find out the weight of 12 mm reinforcement per meter with extreme accuracy, since they will calculate it using a special formula. View available types of foundation reinforcement.

Rebar weight table

You can find out what mass the product has - reinforcement 12 weight 1 meter - from the tables that indicate:

  • weight of one linear m of product;
  • number of rolled meters in one ton;
  • rolled diameter in millimeters;
  • cross-sectional area of ​​the rods in square centimeters;
  • class of steel used in production.
Assortment Weight 1 meter
Weight (theoretical), kg. Limit deviations, %
6 0,222 +9 / -7
8 0,395
10 0,617 +5 / -6
12 0,888
14 1,21
16 1,58 +3 / -5
18 2,0
20 2,470
22 2,980
25 3,850
28 4,830
32 6,310 +3 / -4
36 7,990
40 9,870
45 12,480
50 15,410 +2 / -4
55 18,650
60 22,190
70 30,210
80 39,460

In most cases, using a table, you will be able to find the desired value. If the table did not help determine the weight of 16 mm reinforcement per meter, you can resort to using an online size calculator to make calculations. To use it, you need to know the following parameters: rolled diameter, rod length and number.

The calculator will calculate the total mass for one rod, the total length of the rods, and the volume in cubic meters. There are also calculators that rely on reference data for calculations. To use them, you need to know the GOST according to which the rolled products are manufactured, the material of manufacture and the assortment (name of the rolled products).

There are also products for which this tool is not suitable, one of such products is masonry mesh, the page of which can be found here.

Weight of reinforcement

What to do if you don’t have an online calculator at hand, and you don’t really trust the data from tables on the Internet? It’s simple - you can determine the weight of 8 mm reinforcement per meter yourself using the most common calculator.

To find out the mass of a linear meter of rolled metal, you need to determine the total length of the rods, and then multiply the specific gravity of a linear meter of the product by the number of meters. The formula used for calculation is: 1 m x (3.14 x D x D/4). By performing the actions in brackets, we obtain the geometric area of ​​a circle with a given diameter.

Did not you find what you were looking for? You may be interested in the page with pipeline valves, which can be found here: https://rdmetall.ru/truboprovodnaya-armatura/zatvory/.

Thus, we obtain the weight of a linear meter of reinforcement by multiplying the volume by the specific gravity of the product, equal to 7850 kilograms per cubic meter. An example of calculations for one m of a rod with a diameter of 8 millimeters.

Metal volume: 1 m x (3.14 x 0.008 m x 0.008 m/4) = 0.00005024. Specific gravity: 0.00005024 cubic meter x 7850 kilograms per cubic meter = 0.394384 kilograms.

You can substitute any value of D into the formula and obtain accurate data for any rolled metal, which will allow you to determine the cost of structures for construction.

Source: https://RDMetall.ru/armatura-dlya-fundamenta/ves-armatury/

Reinforcement weight table per 1 meter

Why might the weight of 1 meter of 12 mm reinforcement be required? For example, when pouring the foundation for a private house, builders can tell you the amount of reinforcement in meters, but at metal warehouses, as a rule, reinforcement is sold and the price per ton is indicated. In this case, knowing the weight of one meter, you can calculate how much reinforcement you will need in tons.

For greater convenience, we have provided a second table, which indicates how many meters of reinforcement are contained in one ton for each diameter.

Here's an example of a calculation:

You need 750 meters of 12mm a500c reinforcement (read: decoding of a500c reinforcement).

We look at the line in the first table corresponding to 12 mm reinforcement; the weight of 1 meter is 0.888 kg.

In total we get 750 * 0.888 = 666 kg.

Weight of 1 meter reinforcement table

Reinforcement diameter (mm) Weight kg/meter
5,5 0,187
6 0,222
8 0,395
10 0,617
12 0,888
14 1,210
16 1,580
18 2,000
20 2,470
22 2,980
25 3,850
28 4,830
32 6,310
36 7,990
40 9,870
45 12,480
50 15,410

In industrial construction, a huge amount of reinforcement is used, which is most often supplied in tons. To perform the necessary calculations, you need to know the total length of the existing reinforcement; this can be easily done using the table below.

Calculation example:

You know that you have 25 tons of 10mm reinforcement.

Using the table, we find the number of meters in a ton corresponding to 10 mm reinforcement: 1620 meters.

Total total length of the reinforcement: 25 * 1620 = 40500 meters.

How many meters in 1 ton of reinforcement table

Diameter of reinforcement (mm) Meters per ton
5,5 5347
6 4504
8 2531
10 1620
12 1126
14 826
16 633
18 500
20 405
22 335
25 260
28 207
32 158

Source: https://stroitelnyj-portal.ru/materialy-instrumenty/ves-armaturyi-tablitsa-za-1-metr.html

Reinforcement weight table

Reinforcement is an integral part of any construction process when it comes to high-strength concrete structures. Reinforcement is used both in the construction of foundations and in the construction of heavy loaded floors.

You can also often find less massive structures in partitions and in certain types of finishing work.

The reinforcement, or more precisely the steel from which it is made, is subject to special requirements, which are standardized by GOST, and each reinforcing steel is used strictly depending on the load prescribed by the standards and external conditions.

Reinforcement parameters and weight

Each enterprise that deals with steel rolling complies with certain technical conditions that the fittings must comply with. First of all, this concerns weight. The reinforcement weight table can be used for various purposes - both to calculate transport costs and to calculate the load that the reinforced structure will exert. The table shows the main parameters for the most common types of reinforcing bars.

The weight of reinforcing steel is calculated by multiplying the total length of all rods by the weight of one linear meter; this is why such tables exist.

How many meters are there in a kilogram and how many kilograms are in a meter?

Naturally, whenever this table is needed, it will not be at hand. Therefore, in order to accurately calculate how many kilograms are in a meter of reinforcement, you need to proceed from the volume of the material. Calculating the weight of reinforcement along its length can only be done when we know its diameter exactly.

For an accurate calculation, we use a simple formula - 1m*(3.14*D*D/4). Thus, by calculating the volume of the reinforcement, you can easily find out its weight. To do this, you need to know the specific gravity of steel, which, according to reference books, is 7,850 kg/m³. Length by weight is calculated in the same way. Knowing the specific gravity of steel and the diameter of the reinforcement, you can easily operate with both the length and weight of the rod.

Application of reinforcing steel

Reinforcement, in principle, is a system of interconnected rods, which, when interacting with the concrete mixture, give the final product sufficient strength and rigidity. Reinforcement systems take on all the tensile, bending and compressive loads that a reinforced concrete structure must withstand.

Basically, periodic reinforcing steel is used in the construction of foundations, and is also often used in the construction of buildings by constructing walls by pouring permanent wall formwork with concrete mixture. For such construction, special types of concrete are used, but the requirements for reinforcing steel are the same. They are approved according to GOST 5781-82, and are observed by all metallurgical enterprises.

Dependence of the weight of reinforcement on various factors

As we have already found out, it is necessary to know the weight of the reinforcement during calculations that are carried out to determine the load that the reinforced structure will exert on other elements, or on the soil, if the calculations concern the construction of foundations. Also, construction engineers calculate the reinforcement coefficient of a structure based on the weight of the reinforcement and its volume, so parameters such as:

  1. Diameter of fittings.
  2.  Weight per linear meter of reinforcement.
  3.  Volume of fittings.
  4. The ratio of the volume of reinforcement to the volume of concrete.
  5.  Reinforcing steel grade.

Vital to know in engineering calculations.

Reinforcing steel grade

The weight of any reinforcement is presented in the table that we have posted on the page, and the weight of a linear meter of reinforcement depends on its diameter. GOST clearly defines the standard size of diameters, which we presented in the table. This table also shows the class of steel from which the reinforcement itself is made.

The weight of a linear meter of reinforcement depends not only on the diameter, but also on the shape of the surface of the reinforcing rod or reinforcing wire. The profile can be either smooth or corrugated. The corrugated profile of the reinforcement is necessary in order to improve the adhesion of steel to the concrete mixture, as well as to give additional strength to the reinforcing rod or wire. Depending on the production technology of reinforcing steel, it is divided into three types:

  • hot rolled;
  • cold rolled;
  • cold drawn wire.

It is noteworthy that the mass of a linear meter of hot-rolled steel does not depend on the basic mechanical characteristics it possesses. These characteristics are called steel classes and are designated by the letter A and a digital index.

Imported steel brands are similar in performance, but have slightly different markings and a higher price, so they are used extremely rarely.

Source: https://stroydetali.com/tablica-vesov-armatury_/

Reinforcement: weight per linear meter, formulas and calculation examples

In the total cost of construction, a significant portion falls on the reinforcement of reinforced concrete structures. In retail sales, the price is per linear meter. However, when constructing a foundation, a large amount of reinforcement is required, so it is cheaper to purchase it at wholesale stores. And the wholesale price is indicated in rubles/ton of products. This means that linear meters must somehow be converted into tons.

State standards indicate the weight of one linear meter of reinforcement of a specific diameter. To calculate the required kilograms or tons, you need to multiply the weight of one meter by the total length of all rods of the same diameter. By weight, by the way, the percentage of reinforcement of a reinforced concrete structure is also determined (the ratio of the mass of metal and the volume of concrete).

How to use the table

The table shows:

  • Reinforcement diameter
  • Sectional area of ​​the rod
  • Weight of one linear meter
  • Steel grade

First, in the “diameter of reinforcement” column, you find the product with which you are going to reinforce the structure, then, moving along the horizontal line of the table, you look for the weight of a linear meter.

Table - weight per linear meter of reinforcement

If you don't have a table at hand

Not everyone has the necessary GOST, but each of us studied at school. To independently calculate the weight of a linear meter, basic knowledge of mathematics and physics is sufficient. Everyone knows that mass is equal to the volume of a body multiplied by the specific gravity of the material. The volume is calculated using the formula:

V = F x L, where

  • V – body volume, m3
  • F – its cross-sectional area, m2
  • L – body length, m

The cross section of the reinforcement is a circle. Its area is easy to calculate, knowing the diameter of the rod:

F = 3.14 x D2/ 4 = 0.785 x D2, where

  • D – reinforcement diameter (in meters)
  • 3.14 – the well-known constant value π (it is dimensionless)

As you can see, calculating the cross-sectional area and volume of the rod is not difficult. Now you can calculate the weight of a linear meter. This is also done simply, using the formula:

M = V xp, where

  • p – specific gravity of steel. It is equal to 7850 kg/m3.

There is some inaccuracy in these calculations: the reinforcement is not a smooth rod, and we do not take into account the dimensions of the corrugations. But if you calculate the weight of a meter rod in this way and compare it with the tabular data, you will see that your result is not much different from them.

Calculation examples

As examples, let us consider calculating the weight of a linear meter of reinforcement with the most common diameters of 6 mm and 12 mm of class A III. This material has a periodic profile (longitudinal ribs and transverse protrusions are applied to its forming surface). Special steel is used to manufacture A3 reinforcement. Thanks to the complex surface, metal and concrete form a single monolith.

Reinforcement with a diameter of 6 and 12 mm is used in the construction of dachas, private houses - for reinforcing strip foundations.

  • Let's calculate the weight of a linear meter of A3 reinforcement with a diameter of 6 mm:
    • Sectional area F = 3.14 x 0.006 x 0.006/ 4 = 0.000028 m2
    • Volume per linear meter V = 0.000028 m2 x 1m = 0.000028 m3
    • Weight M = 0.000028 m3 x 7850 kg/m3 = 0.221 kg
  • Let's calculate the weight of a linear meter of reinforcement with a diameter of 12 mm:
    • Sectional area F = 3.14 x 0.012 x 0.012/ 4 = 0.000113 m2
    • Volume per linear meter V = 0.000113 m2 x 1 m = 0.000113 m3
    • Weight M = 0.000113 m3 x 7850 kg/m3 = 0.887 kg

According to the GOST table, weight is 1 linear. m of reinforcement 6 is 0.222 kg, reinforcement 12 is 0.888 kg. As you can see, the discrepancy in numbers is small. It must be admitted, however, that the data presented in the table also does not claim to be highly accurate. They were also calculated theoretically.

In fact, the actual weight of a linear meter may differ from the table by 0.2 - 3%, both plus and minus.

on how to calculate the weight of building reinforcement

The video shows examples of calculating the weight of reinforcement, and also shows the calculation process in an online calculator.

How to calculate the weight of reinforcement in the Masmat program. You can calculate the weight of a linear meter of reinforcement of 16 mm, 32 mm and any other diameter sizes.

Source: https://MegaBeaver.ru/materials/armatura/armatura-ves-pogonnogo-metra-formuly-i-primery-rascheta.html

Reinforcement weight. Weight per linear meter of reinforcement GOST 5781-82

Reinforcement is a set of interconnected elements that, when working together with concrete in reinforced concrete structures, perceive tensile stresses (although they can also be used to strengthen concrete in a compressed zone).

The main application of periodic profile reinforcing steel is in the construction of foundations and walls of buildings and structures made of monolithic concrete. When carrying out concrete work, a significant investment of time and money requires the installation of a reinforced frame to reinforce structures made from reinforcing mesh. To calculate the order volume, you need to know how many kg per meter of reinforcement and the number of linear meters of reinforcing steel.

The weight of a meter of reinforcement is presented in the table of the ratio of diameter and weight of 1 m. Knowing the weight of reinforcing steel according to GOST 5781-82, you can estimate the reinforcement coefficient of the structure (the ratio of the mass of the reinforcement to the volume of concrete) and determine how much material is needed for the foundation (per cube of concrete)

A linear meter of reinforcement is individual reinforcing bars of a smooth and periodic profile 1 meter long, the weight of which depends on the diameter of the reinforcing steel GOST 5781-82 (from a range of diameter sizes of periodic steel - 6, 8.10, 12, 14, 16, 18.20, 22, 25, 28, 32, 36, 40, 45, 50, 55, 60, 70, 80 mm - see RANGE OF FITTINGS).

How much does the reinforcing mesh weigh for screeding, performing plastering work, for making a reinforced concrete foundation frame (concrete + connected reinforcement bars), what is the weight of the reinforcing mesh for brickwork, depends on the size of the cards (length, width of the canvas), the size of the cell (square mm x mm ) and reinforcing wire diameter (mm).

Construction organizations use reinforcement produced in Ukraine, the weight of which meets the requirements of GOST, since domestic reinforcing steel is of sufficiently high quality and complies with all GOSTs and standards for rolled metal.

The weight of the reinforcement is selected depending on the types according to GOST, diameter sizes (see.

table - “Specific gravity of reinforcement in a linear meter”) and the scope of application of the periodic profile.

The weight of a linear meter of reinforcement depends on the shape of the surface of the periodic profile: corrugated or smooth on the outside. Protrusions in the form of ribs, corrugations on the surface of periodically profiled reinforcing steel bars or ribbed wire steel significantly improve adhesion to concrete and its characteristics.

THIS IS INTERESTING:  How to calculate the mass of a metal cylinder

The range of reinforcement, depending on the manufacturing technology of reinforcing steel for reinforced concrete structures, is divided into hot-rolled rod (A1 - A240, A2 - A300, A3 - A400, A500, A600, A800, A1000) and cold-drawn wire steel (VR-1).

The weight of 1 m of hot-rolled reinforcement does not depend on its basic mechanical characteristics, which are divided into six assortment classes depending on the strength of the metal and steel grade, with the symbol: AI, A-II, A-III, A-IV, AV, A- VI.

Reinforcing steel class Profile diameter, mm Reinforcement steel grade
AI (A240) 6-40 St3kp, St3ps, St3sp
A-II (A300) 10-40 40-80 St5sp, St5ps 18G2S
Ac-II (Ac300) 10-32 (36-40) 10GT
A-III (A400) 6-40 6-22 35GS, 25G2S 32G2Rps
A-IV (A600) 10-32 (6-8) (36-40) 80С 20ХГ2Ц
AV (A800) (6-8) 10-32 (36-40) 23Х2Г2Т
A-VI (A1000) 10-22 22Kh2G2AYu, 22Kh2G2R,20Kh2G2SR

For example, A3 construction reinforcement is used to strengthen concrete structures of prefabricated buildings and is widely used by construction companies in Kyiv. The actual weight of construction reinforcement consists of the mass of the reinforcement frames of the elements (foundation, walls, concrete floors) of a monolithic building, welded mesh, which are then filled with concrete mortar over the formwork.

The production of reinforcing steel in Ukraine is carried out using technologies developed in Soviet times in the field of metal processing, and, as a rule, on equipment inherited from the USSR, and that is why domestic manufacturers sell reinforcing steel at a fairly affordable price with good quality and compliance with GOST requirements .

Reinforcement 8, 10, 12, 14, 16, 18, 20, 22, 25 are the most popular in terms of the diameter of the periodic profile, sold by Ukrainian manufacturers. Imported analogues have a higher price.

Before being sold from metal warehouses, fittings in Ukraine undergo step-by-step quality control during the production process, which guarantees high quality that meets state standards GOST.

What is the weight of the reinforcement along its length?

The weight of the reinforcing steel required for purchase is calculated by multiplying the total length of all the bars in the bundle by the weight of a linear meter of reinforcement (see the table of mass 1 m and how many meters are in a ton of reinforcement). Conversion from meters to tons is carried out by multiplying the specific weight of the reinforcement (weight of 1 meter) by the number of linear meters.

Below is a table of reinforcement sections, the specific weight of 1 linear meter A1 (A240), A2 (A300), A3 (A400), A4 (A800), A5 (A800), A6 (A1000), the number of meters per ton to convert weight to total the length of all the rods in the package or coil.

The reinforcement in coils allows you to cut rods of any required length to size, which will reduce the amount of waste and eliminate the need to splice individual rods of standard length (6 or 12 meters).

Table of weight of reinforcing steel. How much does 1m of reinforcement weigh?

Diameter of fittings, mm Weight of 1 meter of reinforcement, kg Linear meters per ton Maximum weight deviations in %
d 6 0,222 4504,5 +9,0 -7,0
d 8 0,395 2531,65 +9,0 -7,0
d 10 0,617 1620,75 +5,0 -6,0
d 12 0,888 1126,13 +5,0 -6,0
d 14 1,21 826,45 +5,0 -6,0
d 16 1,58 632,91 +3,0 -5,0
d 18 2 500 +3,0 -5,0
d 20 2,47 404,86 +3,0 -5,0
d 22 2,98 335,57 +3,0 -5,0
d 25 3,85 259,74 +3,0 -5,0
d 28 4,83 207,04 +3,0 -5,0
d 32 6,31 158,48 +3,0 -4,0
d 36 7,99 125,16 +3,0 -4,0
d 40 9,87 101,32 -+3,0 -4,0
d 45 12,48 80,13 +3,0 -4,0
d 50 15,41 64,89 +2,0 -4,0
d 55 18,65 53,62 +2,0 -4,0
d 60 22,19 45,07 +2,0 -4,0
d 70 30,21 33,1 +2,0 -4,0
d 80 39,46 25,34 +2,0 -4,0

Calculation of the weight of reinforcement, welded mesh

If you don’t have a reinforcement calculation table or an online metal calculator at hand, then you can calculate the total weight of the reinforcing mesh yourself by determining the total length of the wire that makes up the welded mesh measuring 1 m2 and multiplying the number of meters by the specific weight of a linear meter of wire.

In the absence of a reference book, you can calculate the weight of a linear meter of reinforcement yourself, using a regular calculator. The volume of metal in 1 meter of a steel cylinder is 1 m x (3.14 x D x D/4) . In parentheses is the geometric area of ​​a circle with diameter D. The weight of the rod is obtained by multiplying the volume by the specific weight of the reinforcement, which is equal to 7850 kg/m3.

Using this method, you can calculate how many kg are in a meter of reinforcement, and convert tons into meters.

For example, using a calculator, we will calculate the weight of 1 m of reinforcement with a diameter of 12 mm: Volume of metal - 1 m x (3.14 x 0.012 m x 0.012 m/4) = 0.00011304 m3,

Specific gravity - 0.00011304 m3 x 7850 kg/m3 = 0.887 kg. Approximately equal to the value in the table of reinforcement with theoretic weight.

If the length of the reinforcement is 12 m, then we substitute the required value of the rolled steel length into the formula and calculate the weight of the rods. To determine the weight of the mesh, you need to multiply the resulting mass of 1 m2 of mesh by the number of square meters in the welded reinforcement frame.

One more example. Let's calculate the weight of a 100x100x4 mesh with an area of ​​1 m2. The welded mesh consists of 18 welded reinforcing bars 1 m long. The total length of the rods will be 18x1=18 meters. The specific gravity of 4mm reinforcing wire is 0.092 kg/m. Then the mass of a linear meter of mesh with a height of 1 m will be 18x0.092 = 1.66 kg/m2 + 1% of the mass of welding materials.

Source: https://sbk.ltd.ua/ru/sortament-ves-metalloprokata/136-ves-pogonnogo-metra-armatury-gost-5781-82.html

How many rods of 12 rebar are in a ton?

Reinforcement is a set of interconnected elements that, when working together with concrete in reinforced concrete structures, perceive tensile stresses (although they can also be used to strengthen concrete in a compressed zone).

The main application of periodic profile reinforcing steel is in the construction of foundations and walls of buildings and structures made of monolithic concrete.

When carrying out concrete work, a significant investment of time and money requires the installation of a reinforced frame to reinforce structures made from reinforcing mesh.

To calculate the order volume, you need to know how many kg per meter of reinforcement and the number of linear meters of reinforcing steel.

The weight of a meter of reinforcement is presented in the table of the ratio of diameter and weight of 1 m. Knowing the weight of reinforcing steel according to GOST 5781-82, you can estimate the reinforcement coefficient of the structure (the ratio of the mass of the reinforcement to the volume of concrete) and determine how much material is needed for the foundation (per cube of concrete)

A linear meter of reinforcement is individual reinforcing bars of a smooth and periodic profile 1 meter long, the weight of which depends on the diameter of the reinforcing steel GOST 5781-82 (from a range of diameter sizes of periodic steel - 6, 8.10, 12, 14, 16, 18.20, 22, 25, 28, 32, 36, 40, 45, 50, 55, 60, 70, 80 mm).

 How much does the reinforcing mesh weigh for screeding, performing plastering work, for making a reinforced concrete foundation frame (concrete + connected reinforcement bars), what is the weight of the reinforcing mesh for brickwork, depends on the size of the cards (length, width of the canvas), the size of the cell (square mm x mm ) and reinforcing wire diameter (mm).

Construction organizations use reinforcement produced in Ukraine, the weight of which meets the requirements of GOST, since domestic reinforcing steel is of sufficiently high quality and complies with all GOSTs and standards for rolled metal. 

The weight of the reinforcement is selected depending on the types according to GOST, diameter sizes (see.

table - “Specific gravity of reinforcement in a linear meter”) and the scope of application of the periodic profile.

The weight of a linear meter of reinforcement depends on the shape of the surface of the periodic profile: corrugated or smooth on the outside. Protrusions in the form of ribs, corrugations on the surface of periodically profiled reinforcing steel bars or ribbed wire steel significantly improve adhesion to concrete and its characteristics.

The range of reinforcement, depending on the manufacturing technology of reinforcing steel for reinforced concrete structures, is divided into hot-rolled rod and cold-drawn wire steel.

The weight of 1 m of hot-rolled reinforcement does not depend on its basic mechanical characteristics, which are divided into six assortment classes depending on the strength of the metal and steel grade, with the symbol: AI, A-II, A-III, A-IV, AV, A- VI.

Reinforcing steel class Profile diameter, mm Reinforcement steel grade
AI (A240) 6-40 St3kp, St3ps, St3sp
A-II (A300) 10-40 40-80 St5sp, St5ps 18G2S
Ac-II (Ac300) 10-32 (36-40) 10GT
A-III (A400) 6-40 6-22 35GS, 25G2S 32G2Rps
A-IV (A600) 10-32 (6-8)(36-40) 80С 20ХГ2Ц
AV (A800) (6-8) 10-32(36-40) 23Х2Г2Т
A-VI (A1000) 10-22 22Kh2G2AYu, 22Kh2G2R, 20Kh2G2SR

For example, A3 construction reinforcement is used to strengthen concrete structures of prefabricated buildings and is widely used by construction companies in Kyiv. The actual weight of construction reinforcement consists of the mass of the reinforcement frames of the elements (foundation, walls, concrete floors) of a monolithic building, welded mesh, which are then filled with concrete mortar over the formwork.

The production of reinforcing steel in Ukraine is carried out using technologies developed in Soviet times in the field of metal processing, and, as a rule, on equipment inherited from the USSR, and that is why domestic manufacturers sell reinforcing steel at a fairly affordable price with good quality and compliance with GOST requirements .

Reinforcement 8, 10, 12, 14, 16, 18, 20, 22, 25 are the most popular in terms of the diameter of the periodic profile, sold by Ukrainian manufacturers. Imported analogues have a higher price.

Before being sold from metal warehouses, fittings in Ukraine undergo step-by-step quality control during the production process, which guarantees high quality that meets state standards GOST.

Reinforcing steel weight table - How much does 1 m of reinforcement weigh?

Diameter of fittings, mm Weight of 1 meter of reinforcement, kg Linear meters per ton Maximum weight deviations in %
d 6 0,222 4504,5 +9,0 -7,0
d 8 0,395 2531,65 +9,0 -7,0
d 10 0,617 1620,75 +5,0 -6,0
d 12 0,888 1126,13 +5,0 -6,0
d 14 1,21 826,45 +5,0 -6,0
d 16 1,58 632,91 +3,0 -5,0
d 18 2 500 +3,0 -5,0
d 20 2,47 404,86 +3,0 -5,0
d 22 2,98 335,57 +3,0 -5,0
d 25 3,85 259,74 +3,0 -5,0
d 28 4,83 207,04 +3,0 -5,0
d 32 6,31 158,48 +3,0 -4,0
d 36 7,99 125,16 +3,0 -4,0
d 40 9,87 101,32 -+3,0 -4,0
d 45 12,48 80,13 +3,0 -4,0
d 50 15,41 64,89 +2,0 -4,0
d 55 18,65 53,62 +2,0 -4,0
d 60 22,19 45,07 +2,0 -4,0
d 70 30,21 33,1 +2,0 -4,0
d 80 39,46 25,34 +2,0 -4,0

 Calculation of the weight of reinforcement, welded mesh

If you don’t have a reinforcement calculation table or an online metal calculator at hand, then you can calculate the total weight of the reinforcing mesh yourself by determining the total length of the wire that makes up the welded mesh measuring 1 m2 and multiplying the number of meters by the specific weight of a linear meter of wire.

In the absence of a reference book, you can calculate the weight of a linear meter of reinforcement yourself, using a regular calculator. The volume of metal in 1 meter of steel cylinder is 1 m x (3.14 x D x D/4). In parentheses is the geometric area of ​​a circle with diameter D. The weight of the rod is obtained by multiplying the volume by the specific weight of the reinforcement, which is equal to 7850 kg/m3.

Using this method, you can calculate how many kg are in a meter of reinforcement, and convert tons into meters.

For example, using a calculator, we will calculate the weight of 1 m of reinforcement with a diameter of 12 mm: Volume of metal - 1 m x (3.14 x 0.012 m x 0.012 m/4) = 0.00011304 m3,

 Specific gravity - 0.00011304 m3 x 7850 kg/m3 = 0.887 kg. Approximately equal to the value in the table of reinforcement with theoretic weight.

If the length of the reinforcement is 12 m, then we substitute the required value of the rolled steel length into the formula and calculate the weight of the rods. To determine the weight of the mesh, you need to multiply the resulting mass of 1 m2 of mesh by the number of square meters in the welded reinforcement frame.

One more example. Let's calculate the weight of a 100x100x4 mesh with an area of ​​1 m2. The welded mesh consists of 18 welded reinforcing bars 1 m long. The total length of the rods will be 18x1=18 meters. The specific gravity of 4mm reinforcing wire is 0.092 kg/m. Then the mass of a linear meter of mesh with a height of 1 m will be 18x0.092 = 1.66 kg/m2 + 1% of the mass of welding materials.

Source: https://betfundament.com/skolko-hlystov-12-armatury-v-tonne/

ANSWER: 0 meters. (0 rods per millimeter)

The reinforcement is manufactured in accordance with GOST 5781-82 “Hot-rolled steel for the reinforcement of reinforced concrete structures. Technical conditions" and GOST R 52544-2006 "Rolled welded reinforcement of periodic profile of classes A500C and B500C for reinforcement of reinforced concrete structures. Technical specifications"

Depending on the mechanical properties, reinforcing steel is divided into classes A-I (A240), A-II (A300), A-III (A400), A-IV (A600), A-V (A800), A-VI (A1000 ). In the designation A500C and B500C, the letter A means hot-rolled or thermomechanically strengthened reinforcing bars, the letter B means cold-deformed reinforcing bars, and the letter C means weldable.

The number in the designation shows the rounded value of the yield strength in N/mm 2. The yield strength is a mechanical characteristic of a material that characterizes the stress at which strain continues to increase without increasing the load.

What else to read on the site:

Equal-flange steel angle weight calculator. Angle meter weight table. Number of meters of angle in a ton. Dimensions of the metal corner.

Weight calculator for steel unequal angle. Table weight per linear meter of corner. Number of meters of angle in a ton. Metal corner, unequal dimensions.

domatut.rf is a site for professional builders and those who build with their own hands. Articles about the procedure for registration, composition and maintenance of as-built documentation in construction. Examples of correct completion of work logs and acts. Articles about the design and technology of construction and installation works. Calculators for calculating the amount of materials and other useful information for professional builders and those who build with their own hands.

Reinforcement weight calculator
Reinforcement weight calculator. Weight of a meter of reinforcement. Number of meters of reinforcement per ton. Reinforcement diameters table.

Source: https://postroifundament.ru/massa-pogonnogo-metra-armatury.html

Reinforcement weight: table of specific gravity of 1 linear meter depending on diameter

20.05.2017

Reinforced concrete today is the most common material used in the construction of multi-story buildings, roads, tunnels, bridges and any other objects. Reinforcement is an important component of such structures - non-reinforced concrete, although it can withstand significant compressive loads, practically does not work in bending and tension, collapsing under relatively small loads.

But the use of metal rods - regular or prestressed - eliminates this drawback. Often builders find themselves in situations where they need to know the weight of reinforcement in order to calculate the required amount of material for construction. A table of reinforcement weights will help them with this.

You will find it below in the article, in the reinforcement table, the value of the mass of metal rods of all diameters is presented.

What does the mass of rods depend on?

Of course, first of all, the mass of the rod depends on the thickness. The larger the diameter, the greater the weight. Today, in construction, metal rods with a diameter of 6 to 80 millimeters are most often used.

The weight of 1 m of reinforcement, the thinnest, weighs only 222 grams, while for the thickest this figure is 39.46 kilograms. As you can see, the difference is huge.

Therefore, knowing the weight of the reinforcement will also not be superfluous when calculating the pressure of the structure on the foundation - several unaccounted tons of load can have a detrimental effect on the reliability and durability of any building.

How much does the fittings weigh?

In order to find out the reinforcement weight, the easiest and most convenient way is to use the special table presented below.

Rebar weight table

Diameter, mmWeight of 1 meter of reinforcement, kgLinear meters in ton
6 0,222 4504,5
8 0,395 2531,65
10 0,617 1620,75
12 0,888 1126,13
14 1,21 826,45
16 1,58 632,91
18 2 500
20 2,47 404,86
22 2,98 335,57
25 3,85 259,74
28 4,83 207,04
32 6,31 158,48
36 7,99 125,16
40 9,87 101,32
45 12,48 80,13
50 15,41 64,89
55 18,65 53,62
60 22,19 45,07
70 30,21 33,1
80 39,46 25,34

All data indicated in this table fully comply with the current GOST. The error can be a maximum of a few percent - such errors will not cause significant trouble and will certainly not cause damage to the structure.

Having a table at hand, you can quickly calculate the weight of reinforcement, for example, with a diameter of 32 mm. Find the corresponding diameter in the first column and immediately find out that its mass is 6.32 kg per 1 m, and a ton includes 158.48 meters.

Why do you need to know the weight?

Professional builders often have a question: what is the weight of a linear meter of reinforcement. Why do they need this? The fact is that when purchasing rods for the construction of large structures, it is not purchased individually, as in individual construction, but in tons.

THIS IS INTERESTING:  How many 14 rebars are in a ton

But it’s difficult to calculate how long a certain mass of material will last if you don’t know how much a meter of reinforcement weighs. Knowing the total mass and specific gravity of the reinforcement, 1 meter, you can make simple calculations in a matter of seconds, obtaining the total length of the metal rods.

  To do this, we take the entire mass of the necessary rods and divide them by the weight of 1 linear meter.

Calculation example

To reinforce the beams, 2.5 tons of 25-diameter rods are required. We take the value of the mass of 1 meter from the table, equal to 3.85 kg. Next, we convert tons to kilograms, multiply by 1000, it will be 2500 kg, and divide by 3.85, we get 649 meters of material.

The standard length of a metal rod is 11.7 m, to find out the required number of rods, divide 649 by 11.7, we get 55.5 pieces. In this way, you can count the number of rods with any cross-section.

This will help, especially in private construction, to check that the correct amount of material has been delivered to you.

The opposite situation may also occur. The specialist knows how much material he needs, and also knows the optimal diameter. Having found out the theoretical weight of a meter of reinforcement, he just needs to multiply this number by the total length of the required metal rods to determine how much material is needed for construction.

Source: https://VseoArmature.ru/raschet/ves-armatury

Reinforcement 12: Calculation, weight, price

Calculation of the amount of reinforcement. Cost of one meter. Characteristics and GOSTs.

The choice of diameter of rod reinforcement for reinforced concrete structures depends on the load and operating conditions of the object. Starting from 12 millimeters and above, rods are used for load-bearing supports, walls, foundations, building frames, floors, highways, and bridges with significant loads. It is reinforcement 12 that is most in demand in construction. This is due to its high-quality physical characteristics and favorable price.

Steel grades for 12 mm GOST bars

Production is based on the hot-rolled method of producing shaped metal products. According to their technical properties, products are divided into prestressed and non-tensioned. Prestressed ones make it possible to achieve high bending strength, which is important in structures with pronounced lateral pressure. This type of rod is most often made from the following grades of carbon and low-alloy steel:

  • st3, 32G2Rps, 25G2S, 35 GS.

Requirements for steel and assortment for rods d=12 are regulated by: GOST 10884-94, GOST 5781-82. In a concrete structure, reinforcement 12 enhances the strength properties of the finished building.

At the same time, the rods themselves take certain loads and protect the frozen block, for example, a foundation, from concrete cracking during its hardening and operation. This is the main purpose of using rods.

And this type is advantageous due to its high-quality physical characteristics, suitable for the loads of low-rise residential buildings, and an attractive price (compared to higher and more expensive brands).

Features of a periodic profile

Rods of this parameter are produced with a smooth or corrugated surface. Continuous profile rods (corrugated) have undeniable advantages when protrusions are located in a spiral or along the axis of the rod. In the marking, the designation of the diameter of such rods means the average data of 2 values:

  • Internal (implies the diameter of the rod body only);
  • External (indicates the size of the entire diameter, with protrusions).

Parameters: diameters, area, weight, length

Rods of 12 millimeters have a rod body d (internal) of 11.3 mm; d external 13.7 mm. The cross-sectional area is 1.131 cm2. The weight of 1 meter of profile is 0.888 kg. 1 ton contains 1126.13 m of product.

Slicing and packaging

Production is possible in 2 ways: hot-rolled and cold-formed. Rods are produced from ferrous rolled products using the hot-rolled method, and from non-ferrous metals - using the cold-rolling method. The price of the rods depends on this parameter, regardless of the method of cutting rolled metal:

  • Rods of measured length;
  • Profile of unmeasured length in packs.

12 mm reinforcement is packaged in bundles, the range of rod lengths is 6-12 meters. However, by agreement, it is possible to cut the rods into segments of any length from 3 to 25 m. Standardly, 1 rod of reinforcement is cut to a length of 11.75 m. From here you can calculate its weight, which at this length will be 10.43 kg. At the same time, a ton of profile contains 1126 meters.

Reinforcement calculation 12

To calculate how many meters of rods are needed, the total mass is divided by the weight of one meter. It is important to know that rods have theoretical and actual weights, which differ due to the fact that the values ​​are standardized within certain tolerance ranges. That is why the weight when releasing products may differ slightly, up or down from that stated in GOST 5781-82 for one linear meter and the entire order as a whole.

In order to find out the actual weight of the released rods, a control weighing of the total tonnage of the batch is carried out directly during loading. It should be noted that the maximum deviations that regulate weight are also indicated in the standards. If 12 mm reinforcement is weighed, these deviations can range from -6% to +5% according to GOST 5781-82.

Smooth profile

Smooth rods for construction are produced by the hot-rolled method, hardness class A1. Products are cut, as agreed with the customer, either standardly or to custom lengths. This type of profile has no protrusions or ribs. Welded steel reinforcement has the ability to be welded efficiently without loss of tensile and bending strength. This also applies to corrugated products.

Price of fittings dn=12 mm

The price of rod reinforcement is indicated per linear meter and per ton; more often, the manufacturer indicates the cost per ton based on the finished length of the segments. In this case, the customer can receive cuts of any length. Knowing how much 1 ton will cost and the number of meters in it, you can calculate what the price is for 1 meter of rods.

In the Moscow region, 1 meter of reinforcement with a nominal diameter of 12 costs from 24 rubles (periodic profile).

Smooth profile, price per 1 meter:

  • From 29 rubles (retail);
  • From 28 rub. small wholesale;
  • From 27 rub. large wholesale

The price of reinforcement per ton is from 25,900 rubles (grade A500/35GS) with a standard cut of 11.7 m. With a rod length of 6 meters - from 26 thousand rubles. subject to the purchase of a wholesale batch of 20 tons.

The cost of one meter with a rod length of 3 m is 28 rubles. The lowest price per meter is 21.5 rubles. with standard cutting 11.7 m (A3, A500C). Reinforcement with a nominal diameter of 12 millimeters is used mainly for reinforcing high-grade concrete.

Source: https://the-master.ru/armatura/armirovannaya-stal-12-mm

How much does 1 meter of reinforcement 12 weigh?

Very often, reinforcement is used to strengthen a particular monolithic structure or casting. By definition, reinforcement is various kinds of rods and profiles consisting of metal structures of any type of metal.

In construction, this term is heard quite often, since the issue of strengthening the structure under construction is quite tough and acute. Basically, reinforcement is used as a means of connecting concrete mortar and its coupling between cast profiles of a building or structure.

Application of fittings

As a rule, the question of using one or another type of reinforcement is quite relevant, and often completely constant, among builders and engineers. The connection between these two specialties is quite simple. Each of them wants the structure they built to stand as long and as strong as possible. In addition, there are laws and regulations for this, established by the state construction standard.

To strengthen the structure under construction, reinforcing iron blanks of various strengths and thicknesses are used. Basically, their use is inextricably linked with the concept of reinforced concrete material. As a rule, a reinforced concrete element, be it a slab or a block, consists of some kind of frame - metal reinforcement, on which there is a shell of concrete mortar.

This type of building element can significantly increase the load per unit surface area. As a rule, such structures use metal of relatively soft density, such as an iron rod, channel and other workpieces.

But it happens that to strengthen the structure, denser and heavier material is used, for example, an angle, an I-beam or other rolled metals. According to their physical and construction characteristics, such reinforced concrete structures have a number of classifications, the basis of which is the strength class of reinforced concrete.

Thus, the following classes of reinforced concrete structures are distinguished:

  1. Hot rolling design.
  2. Manufactured concrete structures using thermal and chemical treatments.
  3. Durable.
  4. Thermally resistant design.

Certain characteristics assigned to the enormous strength and stability of reinforced concrete structures in construction depend on these classifications and a number of strengths.

For any building material, a distinctive characteristic is GOST, according to which manufacturers of reinforced concrete structural elements roll out the material. It is this standard that regulates the use of one or another type or strength class of reinforcement in concrete mortar.

Clutch nuances

As is clear, the mass of a given reinforcing bar 12 directly depends on what shape and what size it is. It is known that the plane of the rod reinforcement itself can have a smooth surface or have corrugation.

It is worth saying that the best adhesion to concrete mortar occurs due to the corrugated surface of the reinforcement, which is a kind of connecting link between the strength and hardness of the structure.

The entire range of reinforcing material varies depending on how and in what way it was produced. In other words, there are both hot-rolled and drawn rods. It is worth noting that the quality of hot-rolled reinforcement is much better than that of another system of reinforced concrete blocks. But reinforced concrete reinforcements produced by a cold roller have their own number of classifications and advantages in subclasses.

For the basis of correct adhesion of absolutely any reinforcement, it is necessary to know the weight and mass of the metal. It is on the basis of these parameters that one or another type of seam is formed, which is adapted to a given reinforcement. This can be either cold welding or ionic bonding of the metal.

Where is the reinforcement used?

The most common diameter in reinforcement for its use is a 12 mm layer. This diameter is considered the most convenient and optimal among similar reinforcement systems produced with similar diameters. It is also noteworthy that reinforcement with such a diameter is quite easy to bend and itself has a low mass. But when tied together, the reinforcement forms sufficient strength and hardness necessary to hold multi-ton structures.  

Moreover, for the construction and erection of walls in cottages and private houses, according to the standard, a reinforced foundation must be used, which is reinforced with 12 mm reinforcement.

In this option, a strip foundation is used, which also provides for the installation of metal structures for pouring concrete.

To correctly calculate the cost of the required amount of reinforcement with a diameter of 12 millimeters, you need to know its weight over a length of one meter.

But such calculations are necessary only when the structure does not have a layout in the established order, or the process of replacing the reinforced foundation with a higher-quality layer of reinforced concrete occurs. All main characteristics of all structures must be recorded in the documentation for the construction of the facility.

How to calculate the weight of reinforcement?

In order to calculate the mass of the reinforcement used, you need to know some of the minimum parameters of a given metal structure, and these are:

For an accurate calculation, it is necessary to multiply the total length of the reinforcement used by its linear meter. Also, it is not difficult to calculate the cost of fittings. To do this, you need to know the price per meter of length of reinforcement with a diameter of 12 millimeters.

For ease of calculations, it is best to use a special table of reinforcement data, which is available in any specialized hardware store. These tables indicate the ratios of length, width and density of each reinforcing material, as well as their specific gravity calculated per cubic meter.  

When purchasing a small quantity of reinforcement, its weight is indicated in kilograms. But if the purchase occurs in higher mass quantities, then tons are used to indicate weight. In any case, if you know the price of 1 meter of reinforcement with a diameter of 12 millimeters, you can easily calculate the cost of cash costs for the total length of the reinforcement.

Reinforcement weight

For the accuracy of construction work, as well as for calculating the funds spent on reinforcement, it is necessary to know its weight and other parameters.

Finding out the weight is quite simple: to do this, you need to add up the total weight of all the rods used for construction and divide the amount by the number of linear meters.

But linear meters have different price characteristics, which are also related to the parameters of the fittings, in particular the diameter. To do this, you need to use the calculation table of reinforcement parameters, which indicates that reinforcement with a diameter of 12 millimeters has a weight of 0.88 kilograms per length of one meter.

Obviously, to calculate the cost, it is necessary to know all the parameters of this type of reinforcement that are associated with the linear meter. So, in one ton of rods with a diameter of 12 millimeters there are 1126 meters of reinforcement.

Source: https://poznaibeton.ru/beton/ves-metra-armatury.html

Weight of 1 meter of reinforcement - formula and table

During the construction process, an important parameter is the weight of the steel reinforcement, which is taken into account when designing the building. To calculate the mass of a batch of reinforcing bars, you need to know their diameter, mass per linear meter and total length.

Calculation of the weight of smooth and corrugated reinforcement: options

The mass of a linear meter of reinforcing bar can be determined in three ways: using the GOST 5781-82 , which determines the range of this metal product, using a formula and using an online calculator.

Determining the mass of reinforcing steel from the table

The table shows values ​​calculated using nominal diameters and an average steel density of 7850 kg/m3. The nominal diameter of a grooved rod is equal to the nominal diameter of a rod with a smooth surface of the same profile number. This means that the table shows the masses per linear meter of a certain profile number, suitable for both smooth and grooved reinforcement products.

Weight table, kg, 1 linear meter of reinforcement with smooth and corrugated surface of classes A1 and A3

Profile number (nominal rod diameter) Theoretical mass 1 m, kg Profile number (nominal rod diameter) Theoretical mass 1 m, kg Profile number (nominal rod diameter) Theoretical mass 1 m, kg
6 0,222 20 2,47 45 12,48
8 0,395 22 2,98 50 15,41
10 0,617 25 3,85 55 18,65
12 0,888 28 4,83 60 22,19
14 1,21 32 6,31 70 30,21
16 1,58 36 7,99 80 39,46
18 2,00 40 9,87

To determine the mass of a batch of metal products, the mass of 1 linear meter is multiplied by the total footage.

Calculation by formula

M = π *( D 2 /4)* ρ , in which:

M – mass of 1 m, kg,

D – nominal diameter, m,

ρ – density equal to 7850 kg/m3.

Calculation using an online calculator

Determining the weight of reinforcement (kg) by diameter and total length using an online calculator is the simplest and most convenient option.

Source: https://TreydMetall.ru/info/ves-1-metra-armatury-formula-i-tablica

How many kilograms are in 1 meter of reinforcement?

  • Aluminium, duralumin
  • Copper, bronze, brass
  • Tin
  • Lead
  • Zinc

Temporary tensile strength. Thus, one l.m. with a diameter of 12 mm it weighs 0.888 kg. Other characteristics taken into account.

Type of rolled products - to strengthen concrete building structures, hot-rolled bars are required (read about the types of reinforcing bars).

The scope of application includes road construction, production of reinforced concrete products (including piece goods), welded frames and meshes.

It welds without problems, provides excellent adhesion to concrete, has good corrosion resistance, toughness and strength.

It is easy to check this value or find it for rods of a different diameter; the calculation uses basic formulas relating mass, specific gravity and dimensions: V – volume of one linear meter, obtained by multiplying the cross-sectional area of ​​the rod (3.1415 D 2 /4) by its length (in our case – 1 m).

The parameter is controlled by GOST, but taking into account the manufacture of products from different types of steel and differences in the sizes of the ribs, the deviation varies from 0.2 to 3% in both directions. An important nuance: the actual weight of 1 meter 12 mm of reinforcement does not always coincide with the calculated one. The specified formula is also used to determine the total length of the purchased reinforcement, taking into account its weight.

The latter is the cheapest to build due to the reduced content of alloy metals and is considered almost universal. In addition to knowing the weight and footage of reinforcement in one ton, when choosing, pay attention to the following indicators: Parameters of the ribs on the profile: dimensions, pitch, angle of inclination, width.

When purchasing rods with a fixed length individually (in small batches), this fact does not play a special role, but when ordering in bulk, you need to double-check how much the 12 mm reinforcement weighs, in particular, one meter of it. Responsible suppliers indicate this value in their price lists; in fact, each manufacturer has its own. A400 weighs the same (0.888 kg/p.

THIS IS INTERESTING:  What is the melting point of steel

m), it is recommended for strengthening particularly stressed structures, the connection of the rods to each other is carried out exclusively by viscous. The cost of one meter of 12 mm reinforcement varies from 29 to 32 rubles and depends on the type of steel, season and other market factors.

How much does a meter of reinforcement with a diameter of 12 mm weigh? Knowing the weight of one linear meter of reinforcement is required to calculate the amount of material of a certain diameter in a ton and its weight in a future building structure.

How many kilograms are in 1 meter of reinforcement?

The length of the rods and the form of delivery (in coils or in the form of measured sections). For reinforcement with a diameter of 12 mm, V = 0.000113 m 3, ρ is the density of steel, the standard value is 7850 kg/m 3. The minimum grade for prestressing and load-bearing elements made of concrete is corrugated reinforcement with a diameter of 12 mm, as a result, it is the most in demand. The amount of relative elongation (within 14%).

There are standards regulating the minimum permissible proportion of longitudinally placed reinforcement in reinforced concrete products; for example, for a monolithic foundation strip it is 0.1% of the cross-sectional area. Of course, the calculation results are averaged; in reality, the rods do not have a perfectly round cross-section, but a corrugated surface.

Type of steel, its yield strength, admissibility of use in welding joints.

In general, the percentage of steel in reinforced concrete products is quite small, but taking into account the fact that its specific gravity exceeds the density of concrete at least three times, the total mass of the frame or mesh needs to be known and taken into account. Accordingly, one ton includes 1126.12 m. The standard weight (mass) of 1 meter of round reinforcement with a diameter of 12 mm is 0.888 kg, this parameter is standardized according to GOST 5781-82.

But the data obtained is sufficient to determine and verify the required amount of material. Most often, the price is indicated for one ton (from 30,000 rubles and above), the larger the purchase volume, the lower the acquisition costs. Of all the classes offered in private and residential construction, A3 reinforcement made of A400 or A500C steel is most in demand.

Products are sold in dimensionless coils or in the form of rods from 6 to 11.7 m; if necessary, they are cut into pieces of the required size at small retail outlets.

This value is standardized and varies depending on the cross-section of the rods.

see also

  • HOW MANY KILOGRAMS ARE IN 1 METER OF REINFORCEMENT 8Weight of corrugated steel reinforcement A3. Theoretical weight, weight of 1 linear meter of corrugated steel reinforcement A3 (A500C / S500) How much does corrugated steel weigh
  • HOW MANY KILOGRAMS ARE PER METER OF 18 MM REINFORCEMENT? The larger the diameter, the greater the weight. To reinforce the beams, 2.5 tons of 25-diameter rods are required. Of course, first of all, the mass of the rod
  • HOW MANY KILOGRAMS ARE PER METER OF REINFORCEMENT 12 In the construction sector, the most popular products include rolled metal with a diameter of 12 mm. Of course, 1 ton will have 1126.12 meters. In our
  • HOW MANY KILOGRAMS OF REINFORCEMENT ARE IN 1 METER 10 Table for calculating the weight of corrugated steel reinforcement A3. Private trade unitary enterprise "Metallobaza Aksvil". In accordance with GOST requirements
  • HOW MUCH DOES 1 M OF REINFORCEMENT WEIGH? 16 Reinforcement 16 millimeters weighs 1 meter. The material is mainly used in the construction of foundations, walls, buildings and structures made of monolithic

Source: https://trastmetal.ru/blog/skolko-v-1-metre-armatury-kilogramm

How much does 1 kg of 12 reinforcement weigh?

The main area where reinforcement is used is construction. The reinforcement is produced in the form of rods and is used as a basis for strengthening reinforced concrete structures. It takes the main bending and tensile loads, giving reinforced concrete strength, durability and reliability.

The most popular in construction is reinforcement with a diameter of 12 mm, due to the fact that it is quite convenient and lightweight. But, at the same time, when knitting frames and meshes, such reinforcement has the necessary rigidity. In addition, when constructing a strip foundation, which is used mainly for brick country houses, the diameter of the mesh with which the foundation is reinforced should be minimal. 12 mm reinforcement is also used for this.

How much does 1 meter of 12 mm reinforcement weigh?

When estimating the cost of building a house, it is important to know the weight of 1 meter of 12 mm reinforcement. But, it is necessary to calculate this value only if there is no house design or if the diameter of the reinforcing mesh changes. As a rule, the weight is calculated for each structure separately and indicated in the building design.

The total weight of the reinforcement in the entire structure is calculated by multiplying the entire length of the rods by the weight of one linear meter of reinforcement. Knowing the weight of all the reinforcement, you can calculate its market value. But you need to know how much 1 meter of 12 mm reinforcement weighs.

You can calculate this indicator yourself. To do this, you need to take the product of the length of the reinforcement (in this case, 1 meter), the specific weight of the reinforcement (7850 kg/m3) and the area of ​​the circle with the squared diameter.

That is, the weight of 1 meter of 12 mm reinforcement is equal to: 1 m x 7850 kg/m3 x (0.785 x 0.012 m x 0.012 m) = 0.887 kg.

You can purchase reinforcement from construction companies, both by meter and by weight. Since the demand for reinforcement is currently quite high, it is needed not only by large construction companies, but also by small teams building houses. Therefore, reinforcing materials can be purchased in large quantities or in ultra-small wholesale.

When selling, the price of reinforcement per meter is generally indicated, but large companies have now begun to indicate the cost of reinforcement per ton. In this article, a calculation was made of how much 1 meter of 12 mm reinforcement weighs, so you can easily purchase reinforcement that costs both per meter and per ton.

Find out the cost of construction Ask a question Photos Reviews

  • Construction
    • Bath
    • Cottage
    • Pool
    • Veranda
    • Foundation
    • Fence
    • Gates
    • Roof
    • Roof
    • Insulation
    • Gazebos
    • Priming
    • Garage
    • Brick construction
    • Construction of a frame house
    • Construction of a bathhouse
    • Wooden houses
    • SRO
  • Engineering systems
    • Warm floor
    • Air conditioners
    • Heating
    • Septic tank
    • Boiler room
    • Chimney
    • Gas supply
    • Electrical installation
    • Water heating
    • Boiler
    • Circulation pump
    • Heating systems
    • Thermostats
    • Water heated floor
    • Well
  • Renovation of apartments
    • Plasterboard ceilings
    • Partitions

    Good afternoon. I am engaged in construction work. Sometimes I make them to order. It's a lot of work, but you can earn decent money. Now I urgently need a large amount of fittings. I don't know what to bring her with. How much does 1 meter of reinforcement weigh, with a diameter of 12 mm?

    Answers from forum users and experts to the question: How much does 1 meter of reinforcement with a diameter of 12 mm weigh?

    We will make a garden wheelbarrow from sheet iron, a metal profile and two old wheels from a car. Using a metal profile, we create a lower frame for the wheelbarrow, connecting the parts either by welding or bolts. We make a trough from sheet iron in the form of a box with a sloping side. We connect all this by adding two handles and wheels.

    Answer or clarify the question

    Luxury apartments in Moscow

    Popular questions

    How to make heating for free?

    I live poorly. There is no money for repair work. And we still need to do heating. And I want to somehow do it for free. But my problem is that I don’t know what it is.

    What are the reviews on the forums about the construction of wooden houses?

    Hello my dear expert. I want to build myself a wooden house, but I’m still hesitating, maybe brick would be better. Therefore, please tell me. please, any reviews.

    How to make a house project from foam blocks?

    To build any house, both brick and foam blocks, you need to make a house project. At this point I would like to know how much it will cost to do the project.

    How to choose the power of an electric boiler

    The walls are not insulated, the windows are metal-plastic, Uzhgorod

    Tell me where I can get, view or download color tables for choosing colors for design

    Baby room design

    Simple and at the same time stylish design of a room for a baby. A comfortable crib is the center of the image; it is decorated with soft toys that the baby will play with.

    Intelligent production DPR

    The republic has launched the production of unique composite polymer reinforcement, which can be used to reinforce concrete structures. The company Kompozit Group LLC has already received a state certificate of conformity.

    Composite reinforcement (fiberglass reinforcement) is an excellent solution for construction, because the material has excellent adhesion to concrete. Therefore, this type of reinforcement is applicable for the construction of buildings and structures, foundations below the zero ground level, lighting poles, power line supports, insulating power line crossarms.

    The main advantages of fiberglass reinforcement:

    • Unlike traditional materials, non-metallic reinforcement is 3 times stronger.
    which allows the use of a smaller cross-section and is 9 times lighter, which greatly simplifies transportation and installation. • Resistant to corrosion . alkaline environment of concrete and most aggressive environments.

    Its service life significantly exceeds the service life of metal fittings.
    Little weight . (AKP-4, where a diameter of 4 mm weighs 0.02 k7, when metal reinforcement with a diameter of 6 mm (6A-III) weighs 0.260 kg per linear meter).

    • The coefficient of thermal expansion is close to that of concrete, which eliminates cracking due to temperature changes.

    The tensile strength of composite reinforcement is 3 times higher than that of steel.

    Low thermal conductivity . It is not a cold bridge, which significantly reduces heat loss. When exposed to low temperatures, its properties remain the same.

Information: Kompozit-Group is a dynamically developing research and production company specializing in the production and implementation of innovative reinforcing elements made of composite materials, offering composite fiberglass reinforcement AKS d=4mm - 20mm from a warehouse in Shakhtersk.

Contacts: +38(066)-672-05-55, 071-306-15-39

Read 542 times

1 Comment

We have already started receiving questions. Some questions can be answered by following the links in the news. But it’s not difficult for us to answer again: 1. How much does 100 meters of 4-kid weigh? Answer: 4ki weight per linear meter: 0.02 kg 6ki -0.05 kg, 8ki - 0.07 kg, 10ki - 0.12 kg, 12ki - 0.2 kg, 14ki - 0.26 kg 2.

What is the maximum length you can produce? Answer: we can pull it to any length (just have time to thread the thread and add polymer). But we wind the bays, usually 25 - 50 meters long. This will make it easier for you to unwind. 3. What is the diameter of the skein? This is important for transportation. A skein from 4-10 mm in diameter - 1 meter From 10 - 12 mm - 1 meter 30-40 cm 4.

We are interested in your fittings for a greenhouse. But we don’t know how it behaves when bending and what diameter to use.

Answer. If the greenhouse is supposed to be 1 meter in height, then 6-8 mm reinforcement can be used. If you are human height or 2-2.5 meters, take 12mm.

Leave

Source: https://armaturasila.ru/skolko-armatury/skolko-vesit-1-kg-12-armatury.html

Reinforcement weight 12 mm per meter table

Appearance of fittings.

When knitting frames, meshes, as well as when constructing a foundation, the main element is reinforcement. As for private construction, one of the most in demand here is rolled metal with a diameter of 12 millimeters. The favorable ratio of strength and affordable price allows you to use 12 mm reinforcement in the construction of a private house.

Why do you need to know the weight of rolled metal? This value will be needed to estimate the cost of construction work at different stages. Usually the weight is already calculated in the project for each structure where rolled metal A12, A3 or any other grade is used.

If you plan to do the construction calculations yourself or just want to understand this point in detail, then this material will answer all your questions.

After studying the article, the reader will be able to independently carry out calculations and find out the weight of reinforcement 12 mm, A3 or another brand.

Weight calculation

The calculation is performed in linear meters - special quantities usually used in construction work. The table also shows the weight of one linear meter. At the same time, reinforcement is sold by weight, and not by length. The builder's task is quite simple: find out how many meters are required for all structures, and then convert them into units of mass. Below is a detailed and simple table that will help you find out the weight of one linear meter. Weight calculation

In this table you need to find the required diameter (D), in this case it is 12 mm. The second column shows D - this data is not particularly needed, and converting 12 mm is quite simple (you need to divide 12 mm by 100, the result is 0.12 m).

The third column of the table is the most important - the mass m per kg is indicated here. A meter of rolled metal equals 12 millimeters to 0.888 kilograms. Also, as an example, you can take 10 mm rods, the weight of which is 0.617 kg.

The last column shows how many meters there are in one ton.

Calculator

Self-calculation

Now the reader knows how much one meter weighs. But in order to better understand the work, you need to understand the scheme by which the calculation is carried out. Having understood the essence, the builder will be able to calculate the weight of one linear meter of rods with a diameter of 12 or 10 mm.

To perform the calculation, you must proceed according to the following scheme:

The volume of one linear meter can be obtained using the following formula: 1m x (0.785 x D x D). Here the letter "D" represents the diameter of the circle. The total mass is multiplied with the specific gravity of the rods; in all cases it will be 7850 kg/m3.

To find out how much a meter weighs, you need to know the volume.

For example, you can independently calculate the mass of one meter of 10 mm reinforcement. The first step is to obtain the volume - 1m x (0.785 x 0.010 x 0.010) = 0.00010124 m3. The mass of rods is 10 mm – 00010124 m3 x 7850 = 0.616 kg. If you look at the table, one meter of reinforcement 10 weighs 0.617 kg. How much a meter of rods 14 or 16 weighs can be found using the same scheme.

Number of meters in one ton

A more detailed table, where the steel class is also present.

Above is the calculation for 10 mm. The number of meters per ton can also be calculated without using specialized tables. Here it is worth referring to the building regulations, which state that the strip base must contain at least 0.1% of rods in relation to the reinforced concrete structure. This formulation looks quite complicated.

To understand how this works, it’s worth looking at an example:

  1. A strip base is taken, the area of ​​which is 2400 square cm.
  2. Next you will need a coefficient, for this formula it is 0.001.
  3. The resulting volume is multiplied with a coefficient - 2400 x 0.001 = 2.4 cm2.
  4. At the next stages, you won’t be able to do without reference information. Here you will need a manual that indicates the required number of rods.

    For reinforcement with a diameter of 10 and 12 mm, two rods are sufficient.

What you need to know about A12 fittings

Rods are made from steel, the grade of which depends on the requirements for strength, wear and other parameters. Typically, builders choose rods made of low-alloy metal. It cannot be said that this is the most reliable and durable steel, but it does have an important advantage - low-alloy metal can be processed using arc welding.

Grade A12, like reinforcement with a diameter of 10 mm, is usually used to add strength to a structure made of reinforced concrete. Also, these rods are the main element in the construction of frame structures. In addition to this parameter, you also need to pay attention to rental, it differs by class:

  • Periodic profile – A3. Class A3 fittings have transverse corrugation.
  • Smooth profile – A1. Unlike A3, class A1 fittings come without corrugation.

You can purchase reinforcement, regardless of diameter or class A3, in coils or rods.

Source: https://jsnip.ru/stroitelnye-materialy/ves-armatury-12-mm-za-metr.html

Did you like the article? Share with friends:
Metals and their processing
-- Sideb lion (lipk) -->
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]