How to sharpen a razor using foil - Metals and their processing

How to sharpen a razor on jeans to extend its life - Site about

Almost everyone knows that a straight razor needs to be sharpened constantly. But few people know how to sharpen a razor on jeans.

With the advent of disposable and reusable (cassette) razors, people gradually began to forget about sharpening blades. But it turns out that it is also quite possible to sharpen a razor, significantly extending its life.

Considering that cassettes for a good reusable razor are quite expensive, this skill will not be superfluous and will save money.

How to sharpen a razor with improvised means

The razor has been a personal hygiene item for several centuries. The first special hair removal device, the straight razor, had to be sharpened before each use. Moreover, its blade was aimed at the belt directly during shaving.

Modern technologies have made it possible to create safe shaving machines. Many of them, such as "Vest" or "Chic", can be used repeatedly.

But even branded cassettes gradually become unusable and require replacement.

Each blade of the cassette is made of high-strength steel, but it still becomes dull over time and develops burrs, which leads to a painful shave and skin irritation.

Good cassettes for reusable machines (for example, “Vest - 3”) are quite expensive, and sometimes (for example, on a business trip or on vacation) there is simply no time or nowhere to buy them.

It turns out that you can easily extend the “life” of a cassette. All you need is jeans and a little patience. If the denim item will serve further, then sharpening should be done on the wrong side.

For these purposes, thick ribbed denim is best suited.

The sharpening procedure is as follows:

Turn your jeans inside out to avoid ruining the item.
Spread them on a flat surface.
Place a foil roll, a flat narrow block, a narrow ruler or another flat object under the fabric, the width of which is less than the length of the cutting part in the cassette. This is a necessary condition, since there are protrusions along the edges of the cassette that will not allow you to sharpen the blade on a flat surface. The spacer must be placed under the fabric so that the fabric ribs run diagonally.
Place the cassette blade on the block and move it along the fabric in the direction opposite to that in which the machine moves during shaving. And so we grind the blade 50 times, moving it only in one direction.
We unfold the razor and similarly grind the cassette on the jeans, now moving it in the other direction.

After this procedure, you will be able to shave comfortably again. By periodically sharpening cassettes, you can significantly extend their service life. In this way, you can sharpen both disposable razors and branded razors, such as “Vest”.

Instead of denim, you can use a strip of leather of the required width, cut from an old belt or an unnecessary leather item. You should sharpen on the reverse – unpainted side of the leather. Sharpening occurs somewhat faster than on fabric. 20-30 passes in one direction will be enough. There is no need to sharpen in the opposite direction, as with jeans.

Special sharpening devices

Currently, special devices have begun to appear on the market, with the help of which you can easily sharpen the blade of any razor - both budget and reputable.

The simplest of them are designed for manual sharpening. The method is reminiscent of straightening denim.

Only instead of jeans, it uses a strip of special plastic mixed with the smallest abrasive, laid on a convenient base in the form of a block. Such devices include RazorPit (manufacturer – Denmark) and Zattoch (Ukraine).

According to manufacturers, with regular sharpening, a cassette inserted into the Vest machine can last 5-10 times longer.

The same devices can be used to sharpen disposable razors. The process is also very similar to sharpening blades on fabric. Place a drop of shaving gel or foam on the abrasive strip, and then run the cutting part along it in the direction opposite to the movement of the machine when shaving. 20-30 movements are enough for the blade to become sharp.

If you don’t want to sharpen your razor by hand, you can purchase a sharpening machine, for example Save A Blade from Bradex (analogous to Blade Saver made in China).

This small, battery-powered device can quickly sharpen razor blades. It is enough to place the cassette in a special compartment, secure it, and turn on the machine for 5-10 minutes.

The device is universal and suitable for sharpening any cassette razors.

If work to restore the razor's sharpness is carried out manually, then it must be taken into account that the blades in the cassettes are thin and can be broken if handled carelessly. It is necessary to move the cassette along the sharpening surface smoothly, without force, without pressing on the machine.

Sharpening blades in razors will significantly extend their service life, make shaving more comfortable, and also help save a certain amount of the family budget.

Source: https://knaschool50.ru/prochee/kak-natochit-stanok-dlya-britya-ob-dzhinsy-chtoby-prodlit-ego-zhizn.html

How to sharpen a razor at home? — Website about

Numerous manufacturers of men's accessories and shaving accessories offer disposable and reusable razors with blades made of quality materials.

But sooner or later, any blade will begin to lose its properties, especially if you do not provide the machine with decent care, proper operation and storage.

In this regard, experts offer many techniques for sharpening machine blades, many of which can be used at home.

Many men know how to sharpen a razor at home, since several ancient methods have been practiced for many years. Today, many new ideas have been invented that also sharpen blades quickly and easily, extending their service life. It is only important to follow all the details and instructions, otherwise you may damage the sharp cutting surface.

Sharpening a razor at home: what is important to know

Many men believe that sharpening blades for a machine is an unlikely or completely useless task. Especially considering the fact that there is a huge assortment of new blades and cassettes on sale in stores.

In fact, high-quality razors cost a lot of money, as do blades for such models.

Therefore, experts recommend saving money and sharpening blades, unless, of course, you use a cheap disposable razor.

Have you ever sharpened your razor?

Not really

Only a few types of razors can be sharpened using this method:

disposable machine;
reusable razors with cassettes;
T-shaped machines.

If, in addition to proper use and care, the blades are sharpened, a man will be able to provide himself with high-quality wet shaving and save money on the purchase of a machine or blades.

Otherwise, the blades will not only cut hairs poorly and pull them out, but also scrape off the top layer of skin.

An important condition for sharpening is to follow the instructions for all stages, otherwise you can dull the cutting surface even more.

For reference! If a man does not have the skills and knowledge of how to sharpen razor blades, you can contact a specialist who has in his arsenal a machine for sharpening razor blades and other devices for professional sharpening.

Today, the most pressing request from men in forums and communities is as follows - how to sharpen the blades of a Vest razor.

This manufacturer offers high-quality machines with replaceable cassettes, which you can easily extend the shelf life yourself, without the help of a specialist.

Most often, two devices are used for this action - a pyramid razor blade sharpener or ordinary denim.

You can make a pyramid yourself from a material that is incapable of magnetization, for example, plexiglass or cardboard. It is secured with glue or tape; it is prohibited to use metal fasteners. Further sharpening is carried out as follows:

mark the pyramid on a hard, straight surface;
then the pyramid is oriented to the cardinal points;
the razor blades should be placed along the pyramid in the north-south direction;
the blades should lie in this state under the pyramid for 6-8 hours.

The same method can be used to sharpen blades for cassette razors such as Gillette and other brands.

Many men have been successfully practicing the technique for many years, noting its ease of use and high efficiency. Using a special device from RazorPit or Zattoch, blades on a cassette or removable blades are sharpened as follows:

Apply a little shaving gel to the surface of the device;
further along the abrasive surface, but in the opposite direction, as during shaving, movements are made with the machine;
make 25-30 such movements at a time;
At the end, the machine and working fixture will need to be rinsed with water.

Just 5-10 minutes of such manipulations will be enough to revive the blades of the machine and give the razor a second life. This will not only save money, but also provide a man with high-quality and effective shaving of stubble and mustache without irritation and other consequences.

How to sharpen electric razor blades?

Handy tools to help

If a device such as a razor sharpener is not suitable for a man, you can use improvised means, for example, denim. This is one of the first methods that was invented by men many years ago. It is enough to simply turn the fabric inside out, and then run the loom with the blades inside against the direction of the fabric threads 30-40 times, but without pressing.

Another handy method is a leather belt, and sharpening the blades follows the same scenario as with denim.

You need to choose a belt that does not have frayed areas or creases, otherwise the surface of the blades will be damaged. You need to move the blades along the belt from its wrong side.

This will maintain the integrity of the painted side of the belt while improving the functionality of the machine.

Is it important to use special devices?

In fact, any selected razor sharpener should be approved by experts, like a leather belt, pyramid or denim. Other unfamiliar techniques and untested means at hand can easily damage the integrity of the blades, since we are talking about a metal plate with a thickness of 0.5 mm or less. Although there are many razor sharpeners sold online, only a few actually do the job.

“Practice has shown that the Vest razor blade can be used three times longer with the help of such special devices.”

If we are talking about an expensive machine and blades, it is better to purchase sharpening options such as a device from the RazorPit brand or its Ukrainian equivalent from the Zattoch brand.

In such a device you can sharpen both blades and cassettes of a safety razor without fear for their integrity and functionality.

If a man prefers the cheap option of sharpening on jeans, you need to correctly observe the direction of the blades perpendicular to the direction of the threads in the fabric.

Conclusion

Razor accessories all have their own service life, which depends on the materials used in the production of the razor itself and the quality of the blades in it.

Disposable razors are used no more than 1-3 times, but T-shaped razors and reusable razors will last longer if you change the cutting parts on time. And in order not to spend money on buying new “feathers”, you can sharpen them in a timely manner.

To do this, you may need a special device, as well as a pyramid of improvised materials, a leather strap or denim.

Source: https://kdk1.ru/psihologiya/kak-zatochit-britvennyj-stanok-v-domashnih-usloviyah.html

How to sharpen a razor blade at home

During use, a straight razor becomes dull, sometimes becomes bent and needs to be straightened or sharpened. Before each use, such a tool must be adjusted on the belt. Dressing does not sharpen the cutting edge, but only aligns the edges of the metal and minor defects on it, so in some cases it is not enough. For example, after impacts, falls, or contact of the blade with a hard surface, you have to sharpen such a tool using sharpening stones.

To check whether the blade of a straight razor is sharp enough, you need to install the tool with the blade up and bring the hair to it from above (perpendicular to the cutting edge). If it splits in two as soon as it touches the blade, the tool is sharp enough and ready for use.

If straightening the belt is not enough to restore sharpness, it will require sharpening on a stone. It is done differently than sharpening a knife or scissors. This process is quite complex and specific, and the efficiency, shaving quality and service life of the device depend on its implementation. Therefore, ideally, a razor should be sharpened by a master who has the appropriate knowledge, skills and experience.

What you need to sharpen and straighten a straight razor

The blade razor is sharpened at the factory and in the future only needs regular editing - grinding to remove burrs and uneven edges. But if the blade is damaged, it needs sharpening using a stone. This procedure involves removing part of the metal sheet.

The main requirements for a sharpening stone:

homogeneous fine-grained surface – grain size 4000/8000;
stable shape retention;
absence of dense lumps;
minimal release of suspension.

To shave a blade razor, you need a special belt - suspended or with wooden handles. Its width is chosen not less than the length of the blade. This will allow you to evenly process the entire surface of the tool. Editing is performed on a leather and/or fabric belt, without applying an abrasive composition to it.

Processing a tool on a belt with paste is already finishing or sharpening, and it is recommended to perform it only when really necessary, when regular editing does not bring the necessary results. The paste can be applied yourself, and some belts have a factory pasted surface.

How to strop a straight razor on a belt

The algorithm of actions is as follows:

Take the guard by the “shin” on one side and hold it with 2-3 fingers on the opposite side.
Get a clean, smooth belt with clean leather surfaces (no paste) and minimal grain fabric. Any stains on it must first be cleaned, and defects must be sanded. Before use, thoroughly rub the belt with your palm until you feel warm and smooth. Fasten it securely and keep it taut, preferably parallel to the floor.
Place the blade flat on the belt and pull it along it with a “comb”, touching it gently, without strong pressure. Ensure contact across the entire surface, from the ridge to the cutting edge. No effort or pressure! It only causes the blade to bend and prevents the belt from making contact with the end of the edge.
Having reached the extreme point, turn the razor over in a motion reminiscent of rolling a pencil, slowly and carefully, with complete control of the tool. Turn it over the butt, and not through the tip, otherwise there is a high risk of cutting the belt, bending the cutting edge and ruining the razor. Do not allow the tool to stop at the edges: before turning the blade, tear off the edge, and after turning the blade, touch it to the surface of the belt strictly as it moves.
If the tool is in order, 15–40 passes in both directions are enough for it. For every 50 passes on the skin, there are 15 passes on the fabric. Subsequent editing is pointless, since the quality of the cut will remain at approximately the same level.
If the achieved sharpness of the razor does not impress you, sharpen the device on a belt with paste - just swipe it 1-2 times. If the quality of the cut has not improved, after 6-8 passes on the belt with paste, it is useless to continue trying - in such cases, you need to sharpen the product on stones.

THIS IS INTERESTING: What is a corrosion inhibitor?

Rules for storing belts

Clean and pasted belts should be stored separately. It is unacceptable to get abrasives on a clean belt and mix pastes of different grain sizes.

During transportation and storage, it is important to protect such products from deformation - twisting or folding them inevitably leads to the appearance of folds and wrinkles, which are practically irremovable.

Such devices should be stored in cases or closed cabinets to minimize the likelihood of them becoming dusty. It is unacceptable to store such products in damp areas.

Source: https://master-kleit.ru/origami/kak-natochit-lezvie-britvy-v-domashnih-uslovijah/

How to sharpen a Gillette razor blade

Numerous manufacturers of men's accessories and shaving accessories offer disposable and reusable razors with blades made of quality materials. But sooner or later, any blade will begin to lose its properties, especially if you do not provide the machine with decent care, proper operation and storage. In this regard, experts offer many techniques for sharpening machine blades, many of which can be used at home.

Step by step guide

Today, the most pressing request from men in forums and communities is as follows - how to sharpen the blades of a Vest razor. This manufacturer offers high-quality machines with replaceable cassettes, which you can easily extend the shelf life yourself, without the help of a specialist. Most often, two devices are used for this action - a pyramid razor blade sharpener or ordinary denim.

mark the pyramid on a hard, straight surface;
then the pyramid is oriented to the cardinal points;
the razor blades should be placed along the pyramid in the north-south direction;
the blades should lie in this state under the pyramid for 6-8 hours.

Do I need to sharpen my razor myself?

The following facts support a positive answer to this question:

If you take it yourself, you can extend the life of the machine by approximately the same period of time.
Such actions allow you to save significantly, because... When buying a replacement one, you are spending a significant amount of money. And sharpening helps to postpone the trip for new accessories by 2-3 months.
In some situations, it is problematic to buy a new pack of replacement blades. For example, when you urgently need to shave. To do this without being distracted by going to the store, you just need to sharpen the blades.

Having used one of the sharpening methods once, everyone has the opportunity to learn how to do it efficiently and easily. If there is no need for these inventions, of course, it’s easier to run to the store and buy a new pack of cassettes. And anyone who sharpened a blade using one of the methods listed below will probably be happy to share their impressions of a positive result.

Using jeans: sharpening from scrap material

For those who don’t know how to sharpen a razor and need to shave urgently, old jeans will help solve the problem. Processing with this material is simple and accessible to restore the sharpness of the device.

Such sharpening of shaving blades will require a little more time than when processing using special devices. However, the result will be at the same level. To work, you need a round piece of jeans and a dull blade.

Additionally, you need to use a foil sleeve, a ruler, or take another flat wooden object. The width of the latter should be less than the length of the cutting part of the razor. This condition must be observed, because The edges of the blade contain ridges that may interfere with sharpening the razor.

The sharpening process is as follows:

The denim material is placed wrong side up on any smooth surface.
Place a block (cardboard or ruler) under the fabric. In this case, the scars on the tissue should be located diagonally.
Next, apply the razor itself, run it along the fabric and in the opposite direction. This step will take up to 150 movements.
When finishing sharpening, rinse the blade with water.

Read also: How to unscrew the clutch on a Husqvarna chainsaw

The “jeans” treatment process helps to increase the service life of the device by 2-3 times.

Sharpening a cassette in a pyramid

If you are wondering how to sharpen a razor and don’t want to buy any equipment, you can build a special pyramid for this purpose.

This device is useful for repeated use. Sharpening your razor is simple and convenient. When manufacturing, you should proceed from the dimensions of the machine. The device itself can be constructed from wooden slats and any available material that is used to cover the sides of the figure. Using machines with this device is very profitable.

The razor is placed in the inner part of the pyramid with the blade directed north. The device itself is also positioned taking into account the cardinal directions.

Why razor blades become sharp is still an open question for debate. Judging by the reviews of those who tried to build a special pyramid, we can conclude that the method really works.

One razor must be processed in a pyramid for 1.5-4 years. Therefore, the device is considered effective and reliable, despite its secret technique of influence.

Sharpening accessories

When demand arises, supply always appears. Recently, on the windows of some stores you can find special devices that make it easy to sharpen a razor at home. The device itself resembles a special pen, which is equipped with a small plastic strip. On the outer part of which a composition (abrasive) is applied, which sharpens disposable and reusable machines. With this device, the service life is extended several times.

Such devices are easy to use and allow you to achieve good results. To process a razor using such a device, the following steps are taken:

Apply a small amount of liquid soap, gel or shaving foam to the top of the device.
The razor is taken and passed along the abrasive in the direction opposite to the movement during the operation of the blade
To achieve the result, you need to do about 30 movements. And this is enough, the blade of dreams will become sharp.

These are all the methods that solve the question of how to sharpen a razor. Using these simple devices you can save money and extend the life of your blades by several months.

Beard care rules

Tips on how to care for a beard for men who have decided to adopt a brutal look. Description of specialized care products and devices.

Ways to properly and effectively handle your razor

A straight razor whose sharpening is a complex procedure. Therefore, sharpening a straight razor must be done correctly. Effective ways to straighten a razor.

Source: https://morflot.su/kak-zatochit-lezvie-britvy-dzhilet/

How to easily sharpen any razor - Youth information portal

This is a very good way to save your money. Every person who shaves with a razor with replaceable blades, such as Gillette, knows perfectly well how much one replaceable cartridge costs. The price is truly astronomical, although it is reusable, but in my opinion it’s not worth it.

I will show you an incredibly simple and at the same time super effective way to easily sharpen any razor or machine. Even if it is disposable. After such simple sharpening, the blades will cut hairs in exactly the same way as with a new cassette. Don't believe me? I recommend checking it yourself.

Will need

Denim - old jeans are just the thing.
A cardboard sleeve, any kind will do: even foil, even toilet paper, even cling film.

That's all.

Simple sharpening of the razor

The cardboard sleeve needs to be crushed a little and given an oval shape.

This must be done so that the side stops do not interfere with processing - sharpening the blades.

Next, cover the sleeve with denim and align it with your fingers.

And then everything is simple. For perfect sharpening, you need to walk along this tubercle with a razor 100-150 times. The direction of movement of the machine is opposite to the movement when shaving, that is, we move the machine forward.

We do it more than 50 times, then change the direction of movement by 180 degrees so that the hairs on the jeans turn over and the fabric does not get used to it. And we do another 50 movements in the opposite direction.

You shouldn't press too hard, unless it's just a little bit. As a result, the blades even visually shone.

When used, a sharpened razor cannot be distinguished from one just purchased. This incredibly simple tip will allow you to save a significant amount of your budget. Naturally, you won’t sharpen the same machine all your life, but extending its service by two, three or four times, I think, will not be any problem. Make 100-150 movements on jeans, believe me, your hand won’t fall off - it’ll only take 2-3 minutes and as a result you won’t have to waste money.

Watch the video

You can watch the sharpening video in more detail and clearly.

Source: https://dommol29.ru/kak-prosto-zatochit-lyuboy-britvennyy-stanok/

How to extend the life of a razor blade - Epilation - 2020

This article was produced by our experienced team of editors and researchers, who reviewed it for accuracy and comprehensiveness.

Number of sources used in this article: 6. You will find a list of them at the bottom of the page.

wikiHow's content management team carefully monitors the work of its editors to ensure that every article meets our high quality standards.

Shaving can be a hassle for many reasons, including the ongoing cost of replacing razors and blades. With daily use, a regular disposable razor can provide a smooth shave for only 10-14 days - a circumstance on which the price set for razors significantly depends.

As a result of fierce competition, the quality of razors suffers the most, so the main profit comes from their frequent replacement. But consumers can save money and extend the life of their blades by keeping them clean, sharp, and prevented from rusting.

Following some simple steps will help you keep your blades safe for longer.

Sharpening a razor with improvised and special means

Even the best reusable machines become dull over time. The famous brands “Vest - 3” and “Chic” did not escape this fate. You cannot shave with a dull razor. The skin of the face receives microtraumas, through which it is easy to become infected. It takes a long time to treat such a problem, spending much more money on it than a new machine or cassette costs.

p, blockquote 3,0,0,0,0 —>

But it is still possible to keep your face and funds intact. You need to use one of the methods and spend time extending the life of your old razor. That is, sharpen the blade in a new way. It won’t last long, but such savings will be useful for everyone.

Method one

Available means are used - jeans and a narrow, short block of any material. It is recommended to turn jeans inside out.

The inner side of the material has a “ribbed edge” and is better suited for sharpening

The block can be anything - wooden, steel, plastic. Even a cardboard sleeve from foil or film will do. You can take any ruler. The main requirement is that the width of the surface of the bar should not be greater than the working length of the blade on the machine.

p, blockquote 6,0,0,0,0 —>

The fact is that there are protruding plastic stops at the edges of the cassette. They will prevent the tip from coming into contact with the denim material. Ideally, the bar should have a width slightly less than the distance between the stops.

p, blockquote 7,0,0,0,0 —>

Step-by-step instructions for sharpening an old razor:

The jeans are turned inside out.
The fabric is spread on a flat, hard surface.
A block is placed under the denim material.
The fabric on the bar is positioned so that the hem runs diagonally.
Holding the machine with the handle towards you, with smooth movements in one direction (away from you), you need to run the razor over the material at least fifty times.
No need to shave your jeans! That is, do not drag the blade across the fabric in the opposite direction.
Then we turn the machine over with the handle facing away from us and with movements towards us we repeat the operation.

p, blockquote 8,1,0,0,0 —>

Turning is needed to create friction for sharpening. With repeated movements in one direction, the fibers of the fabric lay flat and no longer create resistance. Changing the direction restores sharpening ability.

p, blockquote 9,0,0,0,0 —>

Once the procedure is complete, the blades will look like new for a while. By periodically sharpening, the life of the razor is extended significantly. When the edits are enough for one shave, you should think about buying a new cassette. Savings cannot last forever.

THIS IS INTERESTING: How to quickly sharpen scissors

p, blockquote 10,0,0,0,0 —>

This method is suitable for all types of razors, from disposable razors with one blade to reusable cassettes with multiple edges.

Method three

The process is the same, but a special plastic block is used, with the smallest abrasive applied. On sale you can find a device from two manufacturers from Denmark and Ukraine.

The hand stroke should be smooth, without effort

According to the manufacturer, it is enough to swipe 20–30 times in one direction, and the life of the razor will be extended many times over.

Method four

The Bradex blade sharpening machine can handle the routine work itself. You just need to insert the cassette into the device and secure it. After 10 minutes of work, the tip will be no worse than new. The device runs on batteries. There is a cheaper Chinese equivalent.

p, blockquote 15,0,0,0,0 —>

When manually restoring sharpness, you must remember the fragility of the metal of the blade. Rough movements will cause the thin razor to break.

p, blockquote 16,0,0,0,1 —>

It is possible to give your razor a second life. In our case, recovery occurs to a reasonable extent. The sharpening operation will restore the comfort of your shave and save your wallet from unnecessary expenses.

What is important to know

The main accessory for men's daily grooming that requires attention is machines. Mainly used - disposable, T-shaped or reusable with replaceable cassettes.

It happens that the blade becomes dull or the replacement cassettes run out. You have to shave with unsuitable material, which results in severe skin irritation, abrasions on the face, and the hair is shaved poorly.

Home techniques will quickly restore the original appearance of the sharp material, extend the shelf life, help save money and help out in any situation.

Sharpener RazorPit and cheaper analogue Zattoch

The Danish company RazorPit has developed a sharpener for sharpening blades. This method is proven and has proven itself among users. There is also a budget analogue of the Ukrainian company Zattoch on the market.

An oblong leather plate on an adhesive tape, the surface of which is treated with diamond chips and is itself sharpened.

Using the RazorPit (Zattoch), the blades are sharpened as follows:

A few drops of shaving gel are applied to the surface of the device.
Then the razor moves in the opposite direction.
25–30 movements are recommended.

One procedure per month is enough to turn the machine into a reliable shaving tool. The video shows how to sharpen 3 different blades with a Zattoch sharpener.

Denim

You can sharpen a razor at home on jeans. Denim fabric on the reverse side is dense and rough, copes well with a dull blade.

The jeans are turned inside out.
You need to place a hard thing made of cardboard or wood under your jeans. A ruler, a block, or a sleeve from plastic bags will do.
The razor moves across the fabric in the opposite direction to a classic shave, without damaging the jeans.
30–50 times is enough.

As the machine is used, the procedure is carried out regularly until the material is completely thinned.

Leather belt

You can also sharpen your razor at home using a leather belt. The procedure is similar to the method with denim. A strong belt is selected from thick leather, turned inside out and 25–30 movements are made in the opposite direction. No less convenient and affordable way.

Some sources claim that the pyramid for sharpening a blade was invented by the Czech engineer K. Drobal. It can be bought or made from improvised materials. Cut a square from chipboard or cardboard, and the edges are parallel to each other (the size is indicated in the pictures below). Secure them with tape or glue in the shape of a pyramid. Further, according to the instructions:

place the pyramid on a hard, flat surface,
the design is oriented with its edges to the cardinal directions,
place the blade inside the pyramid on a cardboard pedestal at 1/3 of the height, in the direction from south to north (or vice versa),
keep the cassette in this condition for a week.

The surface of the blades must not touch anything!

Sharpening with a stone

Not everyone can succeed in sharpening shaving blades with a stone the first time; it also all depends on the material. For the procedure, synthetic stones without lumps with a uniform surface are used.

The procedure goes like this:

The stone is wetted with water.
The razor carefully moves along the stone in the opposite direction.
25–30 movements are enough.
When sharpening a straight razor, carefully hold the blade with your thumb and forefinger. You should sharpen first on one side, then turn it over and sharpen on the other side.

Features of sharpening Gillette

You can sharpen a Gillette razor at home using a pyramid or denim. Mak 3 machines have advantages over others, since the company has been producing razors for a long time and knows the needs of consumers well.

To properly sharpen a Vest razor blade using denim, watch the description above or the video.

OPERATING PROCEDURE

To sharpen your razor , dry the blade first. Take old jeans, place them on a hard, flat surface and run the blade along the leg 15-20 times. You can also use a piece of denim for this trick.

Change the direction of the razor head and run the blade over the jeans another 15-20 times. Don't press too hard, just apply light pressure on the machine.
The razor should glide easily across your jeans!

Ready! In a couple of minutes, the razor became as good as new - the sharp blade will not injure the skin and cause inconvenience when shaving! If only I had known earlier that sharpening a razor blade is so easy

I hope you will appreciate this technique and test it in practice! It will save you money, and your skin will be soft and smoothly shaved. Show your friends how to extend the life of your razor: the practicality of the advice is beyond doubt!

Did you like our site? Join or subscribe (you will receive notifications about new topics by email) to our channel in MirTesen!

Watch the video: 3 ways to sharpen and restore the cassette of Gillette Gillette, Bic, Venus, Schick razors. . (January 2020)

Source: https://shelfcosmetics.com/1752-4-ways-to-sharpen-a-razor-at-home.html

How to sharpen razor blades on a cassette

A razor for a man is an item for personal use and daily use for shaving. Regardless of which machine is used, disposable or reusable cassette, the blades in them become unusable after some time. Even those made of high quality steel become dull after a while. It is impossible to shave with them - irritation and small cuts on the skin are guaranteed with such shaving.

Sharpening blades of disposable machines

If disposable razors can be changed without regret, since they are cheap, then changing cartridges in a reusable razor requires significant financial costs. But razors can be given a “second” life by extending their service life several times. Sharpening shaving blades can help with this. This can easily be done at home.

1. Sharpening with denim

https://www.youtube.com/watch?v=0W_JfB6JMDE

This is the easiest way and does not require any financial or physical costs. How to sharpen a safety razor blade if it is a disposable machine? Before you start sharpening, the razor must be prepared by cleaning it from dirt, rinsing it under running water and wiping it dry with a terry towel. After preparation, the following actions are performed:

denim fabric is being prepared. In order to protect it from small cuts, the fabric is turned inside out and placed on the table, that is, on a flat surface.
a solid, even object (ruler, block) is placed under it, having a smaller width compared to the width of the blade. The machine must move freely over the surface of the object located under the fabric.
a dense lining is located under the fabric, the hem of which runs diagonally.
The razor blade is placed on a ruler or block and drawn in the opposite direction to shaving 50 - 60 times.
the machine is turned and the other side of the razor is ground the same number of times.

In this way, the “life” of the razor is extended several times.

2. Sharpening with a leather belt

In addition to denim, good sharpening results can be achieved by using a leather belt or a piece of leather from something. The procedure is carried out according to the same rules as using denim.

The blade of the machine is sharpened on the reverse, unpainted side of the belt.
The result of the action will be faster than sharpening on fabric, due to the density of the belt leather.
You need to move the razor blade along the belt half as much, that is, 10 - 20 times on one side and the other of the shaving surface.

In addition to a regular leather belt, you can use a belt used for straightening straight razors to sharpen the razor. How to sharpen a razor blade on this belt?

A belt for straightening a straight razor is a piece of leather with wooden handles attached to the ends of the belt, or the same piece of leather, but attached to a wooden block, that is, it has a flat surface. Sharpening a disposable razor with this belt is not particularly difficult. After 10 - 20 passes, the blade returns to its previous cutting ability, and the razor becomes as good as new.

3. Sharpening using the forearm

How to sharpen a razor blade if there are no available tools? You can use your own hand to make the razor sharper. The skin on the forearm, covered with vellus hair, resembles the structure of the leather of a belt. This property can be used to advantage.

The disposable razor is carried from the elbow to the wrist.
the sharp part of the machine turns away from itself.
The razor is passed over the skin of the hand ten to twenty times.
Having turned the machine, it should be guided from the wrist to the elbow.

This way you can sharpen the blade of a disposable machine. The quality of sharpening in this case will be slightly lower than the same action carried out on denim or on a belt. This is explained by the fact that the “living” skin of the hand is softer, and the grip on the shaving surface is less than when sharpening on other objects. The result of such sharpening is of less quality. But in some cases this method is quite acceptable.

4. Sharpening using a pyramid

The most unusual method of sharpening razor blades is the pyramid method. Despite the fact that it is patented and exists, the mechanism of this action cannot be explained. To carry out this method, it is necessary to make a certain structure.

4.1. Pyramid parameters

The pyramid is made from various materials. You can use drywall, regular cardboard or chipboard.

The base of the pyramid is a square measuring 500 by 500 mm.
the height of the edge is 400 mm.
rib length – 480 mm.
pyramid height – 320 mm.
the height of the pedestal for the blade is one third of the height of the pyramid, that is, 107 mm.

The structure is glued using Moment glue or liquid nails. The main condition for the operation of the pyramid is the location of the faces and base of the structure along the cardinal points. The installation of the pyramid is carried out according to the compass. The edge of the pyramid is located to the north, and the sharpened blades “look” from south to north or vice versa.

4.2. Sharpening method

The blade of the machine is placed on the pedestal in the finished pyramid. A prerequisite for sharpening is that it does not come into contact with any objects. The razor remains in the pyramid for a week. After this period ends, it regains its original quality of sharpness.

Sharpening blades of reusable machines

Shaving machines are produced not only in disposable, but also in reusable versions. How to sharpen a razor blade on a cassette, and is there any way to do this?

The use of reusable machines takes much longer than disposable ones. But after a certain time, the blades of these devices become dull. You can sharpen a replacement cartridge using the same methods as disposable razors:

using denim;
using a belt;
using the skin of the hand;
using a pyramid.

The effect of sharpening by any of these methods will definitely be, in some cases greater, in others less. This method allows you to extend the life of razors and save money on purchasing new ones. Restoring blades after repeated use means you can always shave with a sharp razor, avoiding irritation and scratches on the skin.

Source: http://depilyaciya-volos.ru/zatochka-lezviy-dlya-britia/

How to sharpen a kitchen knife - 7 steps for beginners

It is simply impossible to describe all the nuances of how to properly sharpen knives in one article, but this is not always necessary. Especially if an ordinary kitchen knife needs sharpening or you are just a beginner who needs to start somewhere.

In fact, sharpening a kitchen knife to a sharp point at home can be done easily and quickly. But the difficulty is that this must be done in such a way that the sharpness of the blade is preserved for a long time, and at the same time too much steel is not removed from the blade.

In this material we will try to simply and clearly tell you how to properly sharpen a knife with a whetstone. After all, this method is not only basic and accessible to everyone, but also the most effective. In addition to step-by-step instructions for sharpening and finishing, here you will find a selection of training videos and an overview of alternative methods - from sharpening systems to the bottom of a ceramic plate.

A little about choosing stones

Sharpening stones come in the following types:

Ceramic;
Diamond;
Natural;
Japanese water stones.

If you wish, once you gain experience, you can buy some solid and expensive diamond stones or Japanese water stones. However, it is better to start with ordinary ceramic bars (such as “Boats”), which are sold in every household goods store. They are wear-resistant, durable and affordable. The only drawback is their uneven abrasion.

Here are tips to help you find the right assistant:

What size should the block be? Ideally, it is 1.5-2 times longer or at least not shorter than the knife blade. The width and shape of the bar is not important.
When purchasing a block, make sure it is flat and free of chips.
To start, you can buy one medium-hard all-purpose whetstone. But if you wish, buy one block with two sides of different grain sizes or two stones with a large and half the grain size. In the future, a couple more stones may be added to your collection.
It's best to try to get a couple of Soviet-made donkeys, say, at flea markets or from your grandfather. Bars marked “Made in the USSR” have uniform-sized grains and high-quality binding material.

To bring your knife to razor sharpness, in addition to sharpening stones, you can also buy GOI abrasive paste, which we will also talk about working with.

7-step instructions for sharpening and finishing a kitchen knife

So, in sharpening a knife, one goal is to remove enough metal from the blade so that the cutting edge becomes sharp again. You need to start work with a coarse-grained abrasive and finish with a fine-grained one.

It is important to remember the following principles of sharpening knives:

The most important thing is to choose the optimal sharpening angle and maintain it along the entire cutting edge while sliding along the block.
Movements should be smooth, without pressure.
All bars must be moistened with water, or better yet, with a soap solution: before sharpening (so that the blade glides better and metal dust does not clog the pores), during the process (to remove the resulting suspension) and at the end, to clean the bar.

And one more important tip - the first time it’s better to practice on a knife that you don’t mind ruining. Especially if your main knife is too good and expensive. Well, let's start practicing.

Step 1. Rinse the stone with water, and then run over it, say, with a sponge with a drop of dishwashing liquid.

Step 2. Next, sit down at the table and place the stone on a wooden board, for example, a cutting board. You can place a towel under the stone. For some it is more convenient to place the block perpendicular to themselves, and for others at an angle of approximately 45 degrees. Over time, you will understand how it is more convenient for you to work.

Step 3. Now you need to decide on the sharpening angle and fix the position of the knife. What should the angle be? The general principle is that the smaller it is, the sharper the blade, and the larger it is, the longer the blade retains its sharpness.

Regular kitchen knives are sharpened to an angle of 40-45 degrees. If you are sharpening a fillet knife (designed for cutting thin pieces of fish, poultry and meat), then you should sharpen it sharper - at an angle of 30-40 degrees. The selected value must be divided by 2, and then we will get the angle that should be between the blade and the surface of the block. That is, to sharpen a blade at 45 degrees, you need to sharpen each side at 22.5 degrees to the sharpening surface.

A simple technique shown in the photo below will help you fix the knife at an angle of 22.5 degrees.

Remember, you should try to stick to the chosen angle throughout the entire work.

Step 4. Place the knife across the block so that the upper edge of the handle is above the lower edge of the stone. Holding the handle with one hand and the blade with the other, we begin to slide along the block away from ourselves along the trajectory shown in the picture below.

Watch a short and clear video:

The point is that the cutting edge sliding along the stone should always be perpendicular to the direction of movement.
At the bend of the blade, the knife handle needs to be slightly raised to maintain the selected angle.
Remember also that you can’t put pressure on the blade, but you shouldn’t give it any slack either.

Thus, you need to pass the blade along the stone about 40-50 times, namely until a “burr” (burr, microsaw) appears along the entire length of the cutting edge. Its appearance will tell you that the excess metal has worn out and there is no point in grinding further. Then you need to turn the blade over and repeat the same steps. Clearly in the video:

A burr is a small roughness that is difficult to see, but can be felt by carefully running your finger along the edge of the blade (but not along the edge, so as not to cut yourself).

Burr of a sharpened knife

During operation, a suspension will appear on the blade - metal dust, which must be periodically washed off with water.

Step 5. So, the burrs have appeared, now we proceed to finishing. To do this, we repeat the same manipulations on a stone with half the grain size. An alternative finishing method is using musat.

Musat is a steel rod of oval or round cross-section with longitudinal notches. It is only suitable for editing and maintaining sharpness, but not for sharpening a knife. It is recommended to edit the knife with musat every time before and after work.

How to sharpen a kitchen knife with musat can be seen in the following video master class from the respected knifemaker Gennady Prokopenkov, who, by the way, specializes in making kitchen knives.

Step 6. If desired, you can bring your knife to a razor sharpness. To do this, take any leather or leather belt, treat it with GOI, Dialux or any other abrasive paste, and then do the same steps, but only in the direction from the cutting edge.

Step 7. Finally, we check the quality of sharpening. This is done very simply. It is enough to cut a tomato or cut paper. If you wanted to achieve razor sharpness, then you should try to shave the hair on your arm. The sharpest knives can even cut hair, as shown in the photo below, but in the kitchen such sharpness is not required for the most ordinary knife.

Alternative sharpening methods

If your kitchen knife is a simple and inexpensive “hard worker” and/or you just don’t want to delve into the “knife culture”, then we recommend using an electric sharpener, a roller knife or a sharpening system for sharpening at home. What are their pros and cons?

An electric sharpener sharpens knives perfectly and quickly, but even the highest quality models remove too much material from the blades, thereby shortening their service life. Another disadvantage of an electric sharpener is that a good device costs more than $200.
A roller knife is an inexpensive and easy-to-use option. With its help, you can quickly sharpen a kitchen knife, but, unfortunately, the sharpness of the blade will not last long and the knife will deteriorate over time. The most trusted tool among roller scissors is the one from Fiskaris (pictured). Do not confuse a roller blade with a V-shaped blade. The latter is an option for the most frugal.

Sharpening systems are good because they allow you to more accurately set and maintain an angle. There are different types of such sharpeners - with blade fixation (manufacturers DMT and Lanski) and with fixation of the stones themselves at a certain angle (Spyderco Triangle Sharpmaker). Separately, we can highlight a sharpening system in which you can select the desired angle and control the position of the knife - this is the Edge Pro Apex Knife Sharpening System. Each system has its own pros and cons. For example, on sharpeners with a fixed blade it is inconvenient to sharpen wide chef knives, but on a triangle from Spyderco the knives are straightened rather than sharpened, and you can only choose an angle of 30 or 40 degrees. However, for kitchen knives these are the angles that are needed, and using a triangle is very simple. A detailed review and operating instructions for the Spyderco sharpener can be seen in the following video.

What are the disadvantages of Apex Edge Pro? Perhaps this is just a high price - $245. However, to sharpen kitchen knives, you can buy a Chinese copy of this sharpener (for example, on Aliexpress).

There is another clever way to sharpen a knife at home - using a rough mark on the bottom of a ceramic mug or plate. The principle of operation is still the same - maintaining the angle, smooth movements, maintaining the cutting edge (cutting edge) perpendicular to the direction.

Source: https://kitchendecorium.ru/accessories-decor/posuda/kak-natochit-nozh.html

How to sharpen the blade of any razor at home: life hacks. Men's website Mensweekly.ru

Thanks to a razor, you can get rid of excess hair on any part of the body, and of course, on the face. It allows you to remove even thick hair as quickly and easily as possible, but for this you must remember to replace the old blades with new ones. Since they quickly become dull, some men try to extend their life and sharpen them. How to do it yourself?

How to sharpen a razor quickly and easily: methods

If you regularly use this tool, you are probably tired of the fact that the blades become unusable too quickly. But they are not that cheap! It turns out that they can be sharpened and made sharper. We are now talking about razors with replaceable attachments, and not about sharpening.

How to sharpen a razor blade at home? Many people think that this requires special tools and devices, but this is not at all true. You will need all the most basic things, we will talk about this below.

Sharpen the blade using old jeans. Turn them inside out and start making the same movements along the fabric when you shave, and also in the other direction. Continue doing this for 2-3 minutes, if necessary, extend this time for a couple more minutes.

You will also be interested in our article What is better to buy - a razor or a machine?

If working with denim is not very convenient, we recommend using a regular plastic ruler. We make movements in the same direction - first in one direction, then in the opposite direction.

How often can this method be used? Do not overuse this, as over time the blade becomes thinner and thinner. Using jeans or a ruler, you will only be able to sharpen the razor a couple of times, no more, then we recommend purchasing a new blade.

Also, if you wish, you can purchase a special sharpening device, which is an abrasive, it is with its help that the blades become sharp. The device can be used for both disposable and reusable machines.

How to use such devices: apply a small amount of shaving foam to its surface, then run it over it not in the direction in which you usually shave, but in the opposite direction. Do 25 such movements, this is quite enough.

What about an electric razor?

Unlike conventional razors, this device has a complex design and you cannot do it without the help of specialists. We recommend not to do this yourself, as you will only break the machine.

How to sharpen a sharp razor: tips

Some men prefer to use a classic - that is, a sharp razor. Learning to use it is not so easy, but those who know how to do it cope with the task without any problems. Its blade also becomes unusable, so it needs to be sharpened. To do this, you will need a sharpening stone or you can contact a specialist, as this process is multi-step and complex. In the video below you will find tips regarding the process of sharpening a straight razor.

If you want to extend the life of your disposable or reusable razor, use our tips. If you want to sharpen a straight razor or an electrical device, we recommend entrusting it to professionals.

Men's magazine Mensweekly.ru

Source: http://mensweekly.ru/page/kak-zatochit-lyubuyu-britvu-lajfhaki

How to sharpen a knife to razor sharpness at home - instructions with video

In principle, this formulation of the question is not entirely correct. If we are talking about the “razor sharpness” of a knife, then we should probably talk about the direct finishing of the blade. after sharpening at home. And this is the second stage of bringing the knife into working condition. Its specifics are worth considering in more detail.

All knives have differences: in the shape of the blade, in its material (there are products, for example, made of ceramics), grade of steel (the best steel for a knife), sharpening angle, and the like. But there are several general rules, following which you can really make the cutting part unusually sharp.

This work can only be done manually. Using various technical means in the form of various “sharpeners” and electric sandpaper will not give the desired result. This is more suitable for the initial sharpening of a knife, when you just need a sharp tool and not a razor.

What you need to polish a knife blade

Bars with different grain sizes. The minimum is 2, although experienced craftsmen use at least 3 for high-quality sharpening.

Leather. Moreover, it is natural, not a substitute, and quite thick. For example, from an officer’s sword belt or other belt.
Paste GOI.
Vaseline (technical).

Sharpening on a whetstone

During the initial processing of the blade on an abrasive with large grains, the direction of translational movement is back and forth. But if the final finishing of the cutting part is carried out, then the technique changes. The blade moves only forward, with a sharp edge. During the “reverse stroke” it should not touch the abrasive.

Finishing

Produced sequentially:

On a fine-grained block

The position of the knife is selected so that its sharp edge is always perpendicular to the motion vector. Sharpening at an angle to the longitudinal axis of the block, diagonally, is pointless.

The picture shows how we are usually used to holding the blade. This is a wrong position.

An option is to do the finishing on fine-grained sandpaper or even wet brick. There is advice that the blade should be moistened with water before processing. You can try, but it’s not certain that it will help, since the grade of steel plays a role.

On the skin

In this case, the position of the blade changes. It is fed forward not by the cutting edge, but by the butt. Moreover, this is done no more than 3 times on one side, after which the position of the blade changes.

To give it the proper sharpness, the leather is pre-treated with GOI. If this product (which is often the case) is a solid substance, then a mixture is prepared on its basis. Powdered GOI is added to the Vaseline and stirred constantly. Then this mixture (or a purchased paste) is rubbed onto the skin.

These are, perhaps, all the tricks that can simply bring a sharpened blade to a state of “razor sharpness.” The difficulty is not in any special technology, but in the need to be extremely careful and maintain the sharpening angle unchanged. This is precisely what prevents many from bringing the knife to perfection.

The author does not claim that this method is the only correct one, since every good owner has his own “professional secrets”. But the fact that the result of such sharpening will be excellent is guaranteed.

Source: https://ismith.ru/tools/zatochka-nozha-do-britvennoj-ostroty/

How to sharpen a razor

The life of the blade can be extended by sharpening it. This can be done on a block placed under denim. Using the inner side of the skin or a special device instead of material increases the efficiency of the operation. You can trust the work to a battery-powered machine.

A good disposable razor or removable shaving cartridge costs a lot of money. But those who care about the skin on their face will think about saving last. To avoid irritation from shaving with a dull blade, buy a new one in a timely manner. And you can save money. It turns out that the life of a spent cassette is extended. To do this, you need to sharpen the razor on jeans or in other ways.

Method two

It differs from the first one only in that instead of a block and denim, a piece of an old leather belt is used. The quality of sharpening improves. It will be enough to swipe no more than thirty times in one direction. The reverse is no longer required. Editing is carried out on the reverse (inner) side of the belt.

THIS IS INTERESTING: How much does channel 16 weigh?