How to install rivets at home - Metals and their processing

How to install fittings on jeans: master class - Master classes on BurdaStyle.ru

How to install rivets and metal buttons on jeans with your own hands using available tools - a step-by-step master class.

Author of the master class

Natalya_Pyhova

Rivets and a metal button are a traditional set of metal fittings for jeans. If you sew jeans yourself, here is a master class on how to install rivets and buttons with your own hands.

For example, rivets and a button can be useful for these models:

You will need:

— a set of accessories (rivets and buttons);

- pliers;

- wire cutters;

- awl;

- hammer;

- an anvil or something that will perform its function (you need something solid, ideally metal, but a thick board made of dense, strong wood will also do);

— rubber mat-backing;

- narrow masking tape;

- marker.

Step 1

Let's look at the fittings first. As a rule, for jeans you need:

— a button (available in different diameters) and the included nail (it can be smooth all-metal, smooth tubular or, as in our case, with a circular notch; it holds better when installed at home);

- rivets, they are also solid (consist of a head, a part located on the outside, and a leg, this is a part that secures the head and is located inside).

Step 2

Decide where you will place the rivets. A simple option: refer to a purchased pair of jeans that you like in this regard for an example. Experienced seamstresses convince us: if you want to put rivets not only on the front, but also on the back pockets, you should think twice about it. The fact is that the rivets on the back can scratch or damage the furniture when sitting.

Step 3

Place the rivets in the desired places and press them into the fabric with your finger. Small circles will remain: place a dot in the middle of each with a thin marker or pen.

Step 4

Make holes in the designated places with an awl. Pierce all layers of fabric, trying not to tear, but to push its fibers apart.

Step 5

From the inside out, insert the parts of the rivet legs into the holes.

Step 6

Using nippers, bite off the excess part of the leg, leaving 1-1.5 mm above the surface of the fabric.

Step 7

If the leg, as in our case, is hollow, then when biting it off it may flatten somewhat (see photo). However, an all-metal leg can also become flattened. One way or another, the leg needs to be trimmed. Do this using pliers or needle-nose pliers, being careful not to overdo it and flatten the leg in a perpendicular direction. Ideally, the leg should return to its original round shape.

If it turns out that the leg was bitten off a little at an angle, it is better to straighten it by lightly tapping it with a hammer from above.

All these manipulations will help to place the rivet more firmly and beautifully, plus they increase its chances of remaining in place for a long time.

Step 8

Place the rubber mat on the anvil, with a sheet of paper on top. Place jeans on top. Place the rivet head on the leg. Hit the head with a hammer quite firmly and with a firm hand. Check whether there is a gap between the cap and the fabric and whether the cap can rotate. if so, hit again. The final result should be the same as in the photo: the cap fits tightly to the fabric (and does not rotate), but the fibers of the fabric are not damaged. Repeat with the remaining rivets.

Step 9

Let's move on to installing the button. Mark the point where the button will be installed.

Step 10

Punch a hole in the intended location.

Step 11

Place the mat on an anvil or board. Place the button bottom side up on the mat (see photo) and secure with two strips of masking tape. Make sure you do not tape the hole in the button shank.

Step 12

Insert the nail from the inside into the hole in the belt. Make sure the stem of the nail is fully inserted into the hole.

Step 13

Place the tip of the stem of the nail in the center of the hole in the button.

Step 14

Holding the belt with your hand (watch your fingers!), hit the head of the stud quite hard with a hammer. Check if the button rotates. If yes, repeat.

Both the button and the head of the stud should fit snugly against the fabric without damaging it. Ready!

Photo and source: imaginegnats.com, iloveyousew.com

Source: https://burdastyle.ru/master-klassy/tips/kak-ustanovit-furnituru-na-dzhinsy-master-klass_19091/

Installing buttons on clothes with your own hands, what you will need for work

Accessories for clothing are not only decorative, but also a functional addition to products. One of the interesting processes that requires separate consideration is the installation of buttons on clothes - a procedure that can be performed in a studio or tried with your own hands. A detailed description of the process will help you understand the installation principles.

Tools

Using rivets on clothes, you can significantly transform the appearance of the product. Most often, metal fittings are used on jeans, leather jackets and other items made of thick fabric. To install the blocks, you will need the following tools:

Press for punching holes. A special device made of steel allows you to instantly punch a hole.
Before making a hole, the master marks it. Then he brings the textile to a special area under the tool and presses the press. Under the weight of the press, a hole is formed - it is always smooth and small. Workshops often use a large number of attachments for different button diameters;
Manual punch. This tool looks like an oblong cylinder of small diameter; it is also equipped with attachments.

The punch helps to obtain smooth and beautiful holes;
Hammer. Without a hammer, the punch will not work. When installing buttons on clothes, the master fixes the punch at the site where the future hole will form and hits it with a hammer several times;
Chalk or soap. These tools are necessary for marking future holes. Usually soap and chalk are used, since the blocks are placed on jeans.

If the fabric is painted in a light color, use a fabric marker.

In addition to the listed devices, you need a mini anvil where the punch will work, an awl for making holes and scissors. Soap or chalk Press Hand punch Hammer

Installation nuances:

To properly attach rivets to clothing, you need to know the principles of the procedure in different cases. You can install the accessories:

For the finished product;
On the part when sewing;
On jeans.

Below are several technologies for working in different cases.

Ready product

A button is a round metal or plastic object used to fasten clothing. There are several types of devices: copper, aluminum, steel, iron. Depending on the type of material, additional tools are used.

For self-installation, use an installation kit for installing buttons on clothing. It consists of 11 items, each of which is designed to work with different types of fittings of different diameters. The set will help you attach the device to clothes, shoes, bags, wallets, and other handmade items.

The procedure for installing rivets for a finished sample of clothing will be as follows:

Product preparation;
Use of special tools;
Functionality check.

First you need to prepare the product: carefully smooth it with an iron, and also mark the places where the buttons will be located. After this, it is recommended to use a special tool for installing fittings and a hammer. It is better to take a small hammer for convenience.

The tool is installed on both sides where the clothes will be fastened, after which it is struck several times with a hammer. Then the buttons are carefully separated from the device. The product already has 2 fastened button parts.

The last step is to check the operation of the buttons: you need to fasten and unfasten the fittings several times to check the functionality and correct installation.

Part when sewn

Manufacturers often install accessories directly during sewing on parts, for example, when making pockets on denim. In this case, the block can be installed by sewing or riveting using special pliers. Before purchasing a sewing button, you should pay attention to its design - it does not have a release mechanism, but is equipped with holes for a needle and thread.

It is not recommended to make a hole for the block with your own hands. The most common mistake is using scissors. Then the hole turns out to be uneven and will become wider over time, which is why the button can easily fly out of the seat.

Many people are interested in the question of how to strengthen the hole for the button: for this you can use special glue - you need to walk the substance along the edges of the hole and leave it to dry for a while.

Select buttons of the sewn type Do not use scissors Sew on the product Strengthen the button with glue

Jeans

The most common problem when wearing jeans is that they come unbuttoned. This means that the button is not securely installed. A short instruction will help you correctly solve the problem of how to rivet fittings on clothes.

Stage	Description
Preparation	For beginners, it will be easiest to purchase buttons consisting of 4 parts. You will also need an awl, a splitting punch, which will help the button open.
Creating a hole	Using an awl, you need to make a hole in the jeans.
Installation	Next, you need to insert the button leg into the hole.
Fixation	After this, you need to place the button on the product on the anvil and hit it with a hammer.

Next, you need to remove the anvil and check the functionality of the button by opening and closing it several times. Select buttons for jeans Prepare an awl Make a hole with an awl Fasten the button leg into the hole Fix it with a hammer

How to remove a broken button

It happens that during wearing, the installed product breaks along with the clothes: how to remove the button in this case is discussed below:

First you need to prepare the tools: you will need a straight screwdriver, pliers, an awl, a file and a chisel;
Before removing the fittings, it is necessary to grind off the head of the rivet with a file;
Care must be taken during the procedure to prevent damage to fingers and clothing;
Having dealt with the head, you need to bend the metal teeth and pull out the rod.

Now, knowing all the nuances of installing accessories on clothes - how to put a rivet and how to remove it - you can safely go shopping for a variety of buttons, blocks and eyelets to add beautiful decorative elements to your wardrobe. Cutting off a button using scissorsRules for removing buttons

Source: https://odezhda.guru/komplektuyushhie/202-ustanovka-knopok

Installing buttons on clothes at home

Accessories for clothing are an additional decoration and accessory. However, even expensive branded clothing is often equipped with low-quality fittings. This applies to both buttons and clips, hooks and zippers. In order not to seek help from a studio, you need to learn how to work with various sewing accessories yourself.

Summary:

Installing buttons on clothes at home will not take much time; this can be done using a simple set of tools. Today we will tell you how to put a rivet on clothes at home, using available materials and tools, thereby saving money by not buying a special press for installing buttons.

Types of accessories

Garment accessories include the following parts:

Buttons.
Hooks.
Loops.
Lightning.
Blocks.
Textile Velcro fasteners.
Holniten are metal rivets. Most often used in denim clothing to secure stitching.
Buckles.
Eyelets. Durable metal or plastic fasteners are mainly used in leather goods.
Rivets. There are utilitarian rivets - those that are used for clamping, fastening and fastening, and decorative ones. Very often, sewing accessories in clothing combine both roles.

Important! All types of fittings are made from different materials.

Often, their quality determines how convenient and comfortable a particular item will be worn. In addition, any accessories are designed to decorate clothing, even if we are talking about such an ordinary detail as a button.

The most popular materials for making fasteners and fasteners:

Metal.
Ceramics.
Plastic.

Important! Most often, sewing accessories are made from a combination of these materials in order to combine practicality and beauty in a single item.

If the part is not selected correctly, that is, without taking into account the characteristics of the fabric or leather, then the fittings simply will not cope with their functions. Then you will have to change the details on your clothes yourself so as not to throw expensive things into the far corners of your wardrobe.

How to install a button on clothes at home?

Of course, if you have the opportunity, then entrust the installation of accessories to a master who has a special press, various devices, a set of tools, and most importantly, experience, thanks to which such work will not take him much time. If you don’t have this option, or you want to find out for yourself how to install a button on clothes, then prepare the following tools:

Awl.
Hammer.
Forceps.
Punch. You will have to purchase this tool. It is necessary to ensure that the hole is smooth and the edges of the fabric do not fray.

Important! You can purchase one punch (the smallest size), but it is better to buy a set of punches with removable attachments.

An anvil (or another hammer).

Adviсe:

Do not cut a hole for the block with scissors, as over time the button or block will definitely “fall out” of it. The hole for the button should be minimal, it is advisable to even slightly stretch the fabric over the leg, since the tighter the fabric is pressed against the part, the more securely it will be fixed.

Punch a hole in leather or fabric using a wooden anvil (not metal) to avoid damaging the tip of the punch. The wood should be very dense (not loose). An area with a knot will do. You can use other dense materials as an anvil that will not damage the punch.

Areas on knitted and bulk materials where holes will be punched can be glued with adhesive fabric so that the edges of the hole do not fray. You can also treat the edges of the hole with silicone glue.

Important! Don't start practicing fastening rivets on expensive clothes right away; practice on something cheaper first.

Rivet installation process

It is necessary to work with tools carefully, slowly and without making sudden movements. Otherwise, the fabric, accessories or tools may be damaged. The most common type of installation of accessories is the installation of a block on clothing. In workshops and ateliers, forceps are used for this procedure. However, such a tool must be purchased of good quality so that the handles do not bend and the “cheeks” do not move.

Important! A sign of good and high-quality pliers are rigid handles that allow you to work quickly and easily.

Don’t despair if you don’t have special forceps at hand; you can do without them at home. Use the following step-by-step instructions:

Use a punch to make a hole of the required diameter in textile material or leather.
Thread the block leg and put a ring on it.
Place the piece of clothing with the block on the anvil.
Use a punch to split the stem of the block into petals. If all the steps are done correctly, the petals should bend on their own on the block ring.
Lightly go over the block with a hammer to finally secure it to the fabric.

Important! Do not use much force when working with a hammer, otherwise you may damage the fabric and bend the block on the front side.

When working, place the ring with the convex side away from you so that it repeats the convex shape of the edge of the block.

How to attach buttons to clothes?

The most difficult process is installing rivets on the rough fabric that outerwear is often made from. Difficulties also accompany installing rivets on jeans. But if you use a good tool and follow all the technological steps, you will probably be able to attach the button to your clothes.

Important! The easiest way to install buttons on jackets, coats and windbreakers are four-part buttons that close using a ring located at the top of the button.

You will need the same tool as when installing the block. Sometimes, special punches are included for this type of button, but using them is ineffective. It is much more convenient to use a punch that splits the stem into petals.

To make a rivet on a jacket or other outerwear, proceed as follows:

Unbend the leg of the four-part button at the top and bottom.
Carry out the standard riveting process (described above).

Important! If you often have to install accessories on clothes, then purchase several types of dowels (a construction nail with a wide head that cannot be bent) at a hardware store. Blunt several dowels of different thicknesses. A construction nail does an excellent job of flaring the legs of rivets, especially if they are very difficult to get to, for example, when installing a denim button.

How to put on a denim button?

To install the simplest button design on jeans, proceed as follows:

Poke a hole in the waistband of your trousers with an awl. Insert the button shank into the hole.
Place the button on an anvil (on a metal surface) and hammer in the shank.
It is the leg, not the button, otherwise you will damage the decorative element.

Important! When buying a denim button, purchase a set that has a threaded stem. Such a leg will be securely held inside the button, but a smooth leg may “pop out” over time under load.

Important! To install a button of a more complex design, the leg of which will move freely, you will need a dowel cut down on sandpaper, since the leg of such a button will need to be flared on the button itself.

Step-by-step instructions on how to install buttons on clothes at home: Thread the leg of the button into the belt.
Place the button on the shaft.
Assess how far the stem extends from the button. If necessary, “bite off” the edge of the part with pliers. Otherwise, the leg will bend and it will be impossible to flare it.
Place the button on the anvil.
Place the dowel on the center of the button shank and, by lightly tapping with a hammer, flare the shank until it fits snugly with the cap body.

Important! Proceed carefully so as not to damage the decorative surface of the fittings.

How to assemble a tendril button for clothes?

In much the same way as a denim button, a button is installed on a tendril-type garment. The only difference is that all manipulations must be carried out only for the top part of the button.

The lower part of the part is much easier to assemble:

To install it, you can buy a special tool with a recess inside in the store.
If you do not have such a tool, then you can use a metal plate with a hole similar to the size of the “bump”. You need to insert the bottom part of the button into the hole of the metal plate, and “slam” the leg with a hammer on the back side of the clothing.

Important! It is quite difficult to install the antenna button without special tools, so buy a little more of them than required.

Adviсe:

If for some reason the buttons are not installed correctly, remove them and install new ones. Do not use damaged buttons as they will not hold securely.
To install a button on clothes at home, you can use the tools that are at hand: a Phillips screwdriver, a bolt, a thick nail, a dowel. To expand the cylindrical part of the button, you can use any cone-shaped device, and then use a bolt of suitable diameter (cylindrical rod) to completely flare the button rod.
Install the button on a smooth wooden surface, but be extremely careful not to break the button or destroy it.
You can use a block of wood to install the bottom of the button if you don't have a suitable metal object with the right hole. Use a drill to make a hole in a wooden block (the diameter and depth should correspond to the male part). Assemble the bottom of the button and place a block on top. Tap the part with a hammer.

How to change a rivet on a jacket with your own hands?

Correctly removing and installing a new rivet is a matter of certain dexterity and skill. However, in order to accurately carry out all technological manipulations, it is necessary to acquire a set of special tools.

Even removing a rivet requires as much care and precision as installing it, especially if you plan to use the removed fittings in the future.

In this case, without special equipment and skill at home, it will not be possible to remove the fittings without damaging the rivet and the fabric adjacent to it.

If you do not plan to use the fittings in the future, then it is enough to “cut off” the head of the rivet using a hammer, anvil or knife, and then install new fittings using the method described above.

Source: https://historyclothing.ru/garderob/ustanovka-knopok-na-odezhdu-v-domashnih-usloviyah.html

Self-installation of buttons on clothes

Of course, only a master with special equipment, a professional set of tools, a number of devices and extensive experience will give a guaranteed result. But it happens that there is no time or money for a atelier, so you have to install the button on the clothes yourself at home. This is not so difficult to do if you prepare the following tools:

Forceps.
Hammer.
Awl.
Punch - creates even holes, you need to buy it.

Important! You usually buy one punch, but with the right approach it is better to purchase a set with interchangeable tips.

Anvil (you can use a second hammer as it).

Recommendations

Do not cut holes using scissors. The hole for the button should be small so that the button foot fits tightly and securely in it.
When piercing leather or fabric, it is better to use a wooden anvil made of dense wood rather than a metal one (ideal if this is an area with a knot).
Areas on knitted and loose materials must be glued with adhesive fabric, otherwise the edges of the hole will crumble. As an alternative, you can use silicone glue.

Important! To gain experience, it’s better to start with inexpensive clothes, because if the result is negative, you won’t feel as sorry for them as branded items.

Installation of rivets

When working with tools, you need to act carefully, slowly, without any sudden movements and with extreme caution. If you rush, the fabric or accessories can be damaged. The most popular type of installation is installing a block on clothing. Craftsmen use tongs, which must be purchased at the studio. A high-quality tool should have rigid handles.

If you don’t have special forceps at hand, this is not a problem if you follow these instructions:

Use a punch to make the desired hole in the clothing.
Thread the block leg and put a ring on it.
Transfer the clothes to the anvil.
Use a punch to split the stem into petals.
Tap the block with a hammer to firmly secure it to the clothing.

Important! Place the ring with the convex side facing away from you. When working with a hammer, you must not apply excessive force, otherwise the block will break or the fabric of your clothing will tear.

Attaching buttons to clothing

The most difficult and responsible process is installing rivets on outerwear. Installing rivets on jeans is no less difficult, but using a set of tools and carefully following the technological steps described in the article, you can make this task simple and feasible.

Important! The easiest way to install buttons on outerwear are those that are assembled from four parts connected by a ring.

Having prepared a set of tools, you can proceed to installing buttons on outerwear, this should be done like this:

Unbend the leg of the button from the bottom and top.
We carry out the riveting process.

Replacing buttons on a jacket with your own hands

To correctly and quickly install a new rivet or remove an old one, you need skill and dexterity. In order to improve the quality of work and make it as thorough as possible, you need to purchase a set of special tools.

Any technological manipulation requires maximum accuracy and attentiveness, otherwise everything will go down the drain.

If the old fittings are no longer useful in the future, then you can simply “cut off” the head of the rivet with a hammer or knife, placing the fittings in the same way as described earlier.

Installing a denim button

To put a button of a simple design on jeans you need:

Using an awl, make a small hole in the waistband of your pants.
Insert the button stem there.
Place the button on a metal anvil and hammer in the stem. It is the leg that needs to be hammered, not the button, because you can ruin its appearance.

Important! For jeans, it is better to choose fittings whose legs are threaded. Thanks to this cutting, the stem will fit well inside the button and will last for a very long time. If you install a button of a complex configuration, then you need to use a sawed-off dowel, with the help of which the leg on the button will be flared.

Self-installation of the button on clothing is carried out as follows:

Thread the stem of the button into the belt.
Place the button on the shaft.
Check how far the stem comes out of the button; if necessary, you can “bite off” its edge with pliers.
Place the button on the anvil.
Place the dowel on the center of the leg and gently (not too hard) tapping with a hammer, flare the leg until it fits tightly onto the button.

How to assemble a mustache button?

The tendril-type button is installed in almost the same way as a denim button. There is only one difference - technological processes are carried out only for the upper part of the button.

The lower part of the part is much easier to assemble:

First of all, you need to buy a special tool with a recess inside. An alternative solution is to use a metal plate with a hole. It is into this hole that you will need to insert the bottom part of the button, slamming the leg with a hammer on the back of the clothing.

Important! It is difficult to install the antenna button without tools, so it is advisable to purchase the entire necessary kit.

How to install a button on clothes at home - step-by-step instructions and video - Portal about computers and household appliances

In order not to seek help from a studio, you need to learn how to work with various sewing accessories yourself. Installing buttons on clothes at home will not take much time; this can be done using a simple set of tools.

Today we will tell you how to put a rivet on clothes at home, using available materials and tools, thereby saving money by not buying a special press for installing buttons.

general description

Modern riveters appeared relatively recently; before that they were bulky and inconvenient for home use. But the constant work of engineers on this problem has yielded results: manual riveters have become compact, and most importantly, they reliably connect parts with each other with minimal physical effort. The device itself has become quite simple and easy to use.

It provides access to both sides for a more reliable connection. In this case, no outside help is required. The main thing you need when working with manual riveters is pre-drilled holes for rivets in the parts to be joined.

Almost anyone can cope with such work. At the same time, the price for manual riveters is low.

Nuances

This button has two components. If you have no work experience, you will have to prepare for incorrect fixation, so it is better to have several components. Every action is thought through, thereby eliminating repeated processes and the purchase of a new part. The basic principles are accuracy, precision, and the presence of the necessary auxiliary components. When failure occurs, it will lead to damage to the clothes themselves.

Source: https://instanko.ru/ruchnoj/kak-zaklepat-zaklepku.html

Types of buttons

First, let's look at what types of buttons there are. Indeed, depending on the fittings, various methods of its installation are provided.

The O-shaped (or ring) button, as the name implies, has the shape of a ring.
S-shaped (aka “Alpha”) are spring-type buttons. They come either sewn on or with tubes for fastening.
Shirt. It consists not of one pin, but of several spikes. Such buttons are attached to thin fabrics or knitted and knitted items. Often used for children's things.
Magnetic. This is a self-fastening fitting with magnetic fixation. You can often find such buttons on wallets and bags.

Koburnaya. In this case, when installing the button on clothing, a screw design of two elements is used. It is screwed into leather jackets, bags, belts with a screwdriver, and is also used in a holster (hence its name).
Klyamernaya or block. The lid has a ring fastening. If the button is fastened, you can see the second side fastener in the center.

If you decide to install the fittings yourself at home, then you need to have the following materials:

button consisting of 4 parts;
pliers or small hammer;
a piece of thick rubber, you can use a plumbing gasket;
steel knitting needle;
punch (you can use a Phillips screwdriver or dowel);
wooden block.

Why do you need a punch?

This is a necessary item when installing a button on clothing. Even if you are not a professional seamstress, but simply decided to change the button on things yourself, you still need to purchase a punch or at least find a replacement for it.

It is used to make a neat hole in the fabric. If you pick at it with scissors, it will just be an uneven hole, over time it will stretch and the button will fly out. Using a punch, this can be done, firstly, quickly and accurately, and secondly, in a minimal size.

The pin of the button should be pulled firmly onto the fabric.

If the fabric has split edges, then the hole made by the punch must be lubricated with glue, then the edges will not crumble and the button will be firmly fixed in the hole. You can use adhesive fabric.

If you decide to take up sewing professionally, then it won’t hurt you to purchase a device for installing buttons on clothes, as in the photo above. This 11-piece set consists of a base plate and various sized punches.

This purchase will significantly speed up the process of installing buttons on clothes at home. If you have a one-time installation job, then instead of a punch you can use a steel knitting needle.

If the fabric is split or knitted, then the knitting needle needs to be heated over a fire.

Step-by-step instruction

After a punch has made a neat hole in the marked area, the button is threaded through. A fixation ring is placed on top. Be sure to check that it is positioned away from you along the convex edge of the button.

Then you need to place the product on a dense surface. This could be a wooden block or a rubber gasket. Do not use a metal base, as it can deform the surface of the button when struck by a punch. And this doesn’t suit us at all.

The punch is inserted into the leg of the button and, by pressing, it is divided into parts (usually four). They should lie on the fixation ring. All that remains is to press these metal petals into the fabric with a hammer. To do this, use a hammer, but be careful. There is no need for brute physical force here, as you can damage the button. A little effort will be enough.

Just in case, buy a few extra barrels, in case you won’t be able to carefully hammer in the pin petals the first time, and they will break. This kind of problem is not uncommon for beginning craftsmen.

Installing shirt buttons

This type of button is considered the simplest. Here, the main tool for installing buttons on clothes will be pliers. The installation process is similar to the previous option, only the punch needs a larger diameter.

The front parts are installed first, then the internal parts. After marking with a simple pencil, the crown of the button is pierced into the fabric. Then the product is laid on a wooden beam and the inside is hammered with little effort.

The second part of the button has an S-shaped pin. To hammer in this part, it will no longer be possible to use a wooden beam, except perhaps to drill a hole in it. Usually, when installing buttons on clothes at home, use a nut of the appropriate diameter.

Repairing a damaged button

If you had an incident when installing a shirt button and something went wrong, do not despair. The good thing about these buttons is that they can be removed and reused. To do this, you need to straighten the teeth of the crown and remove it freely from the fabric. You can remove the button with a flat screwdriver or knife. You can straighten the ends of the crown using pliers or small pliers.

Once the teeth are aligned, the button can be reused. This method is also applicable in cases where the button is intact, but the fabric in this place is torn. Then, after carefully removing and restoring the button, it can be installed back on the product, just in a different place.

Press for installing buttons on clothes

The best assistant when sewing clothes with buttons is a special press. It consists of an upper and lower stand and a set of screw-on attachments. A punch is screwed into the upper part of the press, and a stand for the punch is screwed into the lower part.

This press is used for different fabrics, both thin and thick, even leather belts. You can purchase different attachments; they are sold separately. It is advisable to sign them immediately so as not to confuse the size.

Each set is designed for a specific button size.

Using this device to install buttons on clothes is easy. Let's take a closer look at how to do this:

We install the attachments - screw the top one in until it stops, but not too zealously, and simply insert the bottom one into the round groove of the press.
Since there are two sets of attachments for installing Alpha buttons, they are installed alternately for one and the other pair (such buttons consist of four parts).
Nozzles are selected according to the size of the button. Typically, the most commonly used punches are purchased - 2, 4 and 6 mm.
It is important to correctly mark all the holes and punch them in advance with a punch; it is recommended to do this with a piece of reinforcing fabric.
When all the holes are punched, the nozzles are replaced, and then work continues with the fittings. Advice: it is better to punch holes of a smaller diameter. The button pin must be pulled firmly through it, otherwise the button will subsequently fall out.

Procedure

Here's what you need to do:

First, a hole is punched in both the fabric and the pad (if there is one).
We replace the punch with an attachment for the eyelets.
A part of the button is placed on the lower part of the press with the pin facing up. We place the fabric on top with the wrong side up, aligning the hole with the pin. If necessary, either a piece of fabric or a reinforcing plastic ring is added.
A counter washer is placed on top. Its concave side should point down.
We press gently and smoothly on the handle of the press. In this case, the pin is flared. The button is firmly installed on the fabric.

First, the attachments for the lower elements of the button are replaced. The wrong side of the fittings is placed underneath. It comes with a long pin. First, reinforcing fabric is placed on top of it, then the main material, face up.

The other part of the button with a small S-shaped pin is placed on the top nozzle with a plastic tip. After this, press the press handle all the way, but carefully. This completes the process.

Forceps

If you want to purchase a machine for installing buttons on clothes, it is best to use tongs. This is a very useful tool that will greatly facilitate the work of a seamstress. As professionals advise, there is no need to save on such a product. Cheap tongs often have handles that break. Typically, attachments for various buttons are sold in the kit for this tool.

The appearance of the tongs differs greatly from different manufacturers, but the method of use is similar.

The handles of the tongs have a lock. When starting to work with such a tool, you need to squeeze the handles and remove the lock. Places for buttons are marked in the fabric and holes are made with a punch. Then the button is inserted into it with the head facing up and the tongs are compressed. You need to press smoothly, but all the way.

Helpful information

In order to ensure that the back and front parts of the button match exactly and wrinkles do not form on the clothing, you need to accurately mark the installation locations of the individual elements. Some people use the following method: install the lower parts first, and lubricate the pin with chalk. By aligning the edges of the clothing, the chalk leaves a mark in the right place. After this, it is easy to find the desired point for the upper parts.

Some people don't like this technique. They use a different way of marking. Craftsmen measure the distance with a pencil or use a self-disappearing marker. In this option, the upper front elements are installed first, and only then the lower ones.

In the article, we looked in detail at different ways to install buttons at home. We hope that the tips will help you complete this type of work quickly and efficiently.

Source: https://FB.ru/article/369537/ustanovka-knopok-na-odejdu-v-domashnih-usloviyah

How to rivet a rivet at home video

The rivet is an excellent and durable type of fastener. But unlike bolts, nuts, studs and screws, it cannot be removed without damaging it. The bolt can be unscrewed with keys or a screwdriver, after which it can be reused. The broken rivet will have to be thrown away. The question also arises: “How to rivet rivets if there is no riveter in your arsenal?”

The essence of the rivet

The rivet is a disposable fastener. But it is also the cheapest. If the device is being made permanently and does not involve disassembling parts in the future, these parts can be riveted together. They will hold just as firmly as screws, but will be even more reliable. The screw may come out over time, but the rivet itself will not come apart, since it is impossible to rivet it without the help of special tools.

Rivets in construction and mechanical engineering

There are many types of rivets. Some have the form of a single part - a bushing, which is inserted into the hole and, using a special riveter, the edges of the bushing are expanded on the other side of the parts being connected and pressed (flatten). Such rivets are the most common, cheap and reliable. They are used mainly in construction and mechanical engineering. How to rivet construction types of rivets?

Removing a construction rivet

It is difficult to call this action dismantling as such. This is removal. To remove the rivet, you will need the regular rivet gun that was used to install it. But since you don’t have one at hand, it’s worth figuring out how to rivet a rivet without a riveter.

You can try to remove rivets in which the head or bent part protrudes above the plane of the riveted parts with a sharp chisel and hammer:

Place the cutting part of the chisel exactly under the head (or bent part).
Hit the chisel with a hammer. Some large rivets may take several hits to break off.
Once the head (or bent part) is torn off, all that remains is to remove the rivet from the hole. This can be done by pushing it out with a nail or other thin object (for example, a screwdriver).

But more often you cannot get to the caps and curved parts, since they are, as it were, in the body of the parts being fastened. At the factory, special grooves are drilled for the caps and expanding parts in the parts, and then the rivets fit into the metal like a glove. How to rivet rivets in such a “tricky” case?

Here a screwdriver (or drill) with a metal drill selected for the diameter of the rivet will come to the rescue. Proceed as follows:

Using a core, make a notch on the head of the rivet so that the drill does not wander, although some are accustomed to doing without serifs.
Place the screwdriver bit on the head and drill out the inside of the rivet.
When the drill goes through, the remains of the head and widened part fall out on their own.

Rivets on clothes

But rivets are also used in the manufacture of various types of clothing. Their use began in the 19th century, when, while sewing pants made of rough canvas, which will later be called jeans, one of the craftsmen noticed that if the seam is riveted at the beginning, it will definitely not come apart or tear.

Here rivets are used, for which the name “buttons” is more appropriate. Unlike ordinary ones, they consist of two parts - internal and external. Everything is held together by the fact that the head of one element fits into the cavity of another. Then, under pressure from the riveter, the head of the internal element is flattened (expanded) inside the cavity of the outer element, and such a “super button” cannot be broken, no matter how hard you try. The fabric is more likely to tear. How to rivet these types of rivets correctly?

Removing rivets from clothing

This is done in two ways. One - with the help of side cutters, the other - with a knife and a pair of pliers. The choice of methods depends on what type of rivet you have - alpha (internal) or beta (external).

The corners and edges of the stitching are mostly riveted with alpha varieties, otherwise known as grommets. Beta is used in cases of buttons used to fasten clothing. One part there is alpha, and beta is riveted onto it.

Despite the fact that such rivets hold the material perfectly, they are afraid of mechanical stress.

How to rivet alpha rivets using a knife and two pliers?

Carefully, so as not to damage the fabric, insert a sharp knife blade under the edge of the wide part of the rivet on one side and bend it back so that the edge can be grabbed with pliers.
Do the same with the opposite part of the rivet. Insert the knife blade and bend the edge.
Grasp the outer folded part of the rivet with the edges of one pair of pliers, and the edge of the back folded part with the other.
Pull in different directions and the inner part will come out of the outer one.

It is done.

How to rivet a beta rivet on clothes? Everything is even simpler here. The procedure is as follows:

Grasp the garment with the widened (curved) part of the rivet protruding inside the pressure washer facing you.
Take side cutters (it is advisable to use those with pliers), place them under the very bottom of the widened part and squeeze.
Twist and squeeze again.
At some point, the upper element will jump off the lower one on its own. Or when there is enough space between it and the lower element, the inner part that fits into the pressure washer can simply be cut through without harm to the material.

It is done.

Source: https://strinstrumenty.com/uslovie/kak-zaklepat-zaklepku-v-domashnih-usloviyah-video.html

How to install a button on clothes at home - step-by-step instructions and video. How to put a rivet on clothes at home

At homeHow to put a rivet on clothes at home

Today we will tell you how to put a rivet on clothes at home, using available materials and tools, thereby saving money by not buying a special press for installing buttons.

Adviсe:

Do not cut a hole for the block with scissors, as over time the button or block will definitely “fall out” of it. The hole for the button should be minimal, it is advisable to even slightly stretch the fabric over the leg, since the tighter the fabric is pressed against the part, the more securely it will be fixed.
Punch a hole in leather or fabric using a wooden anvil (not metal) to avoid damaging the tip of the punch. The wood should be very dense (not loose). An area with a knot will do. You can use other dense materials as an anvil that will not damage the punch.
Areas on knitted and bulk materials where holes will be punched can be glued with adhesive fabric so that the edges of the hole do not fray. You can also treat the edges of the hole with silicone glue.

Important! Don't start practicing fastening rivets on expensive clothes right away; practice on something cheaper first.

How to attach buttons to clothes?

Important! The easiest way to install buttons on jackets, coats and windbreakers are four-part buttons that close using a ring located at the top of the button.

You will need the same tool as when installing the block. Sometimes, special punches are included for this type of button, but using them is ineffective. It is much more convenient to use a punch that splits the stem into petals.

To make a rivet on a jacket or other outerwear, proceed as follows:

Unbend the leg of the four-part button at the top and bottom.
Carry out the standard riveting process (described above).

How to install a button on clothes at home - step-by-step instructions and video

Accessories for clothing are considered one of its main decorations. Often, even the largest and most expensive brands use low-quality materials, which is why they become unusable over time. This applies not only to hooks and zippers, but also to buttons. In order not to seek help from a studio, you need to have the skills to work with fittings yourself.

Installing buttons on clothes at home usually takes little time, which is why it can be an opportunity to spend your leisure time pleasantly and usefully. In our article we will talk about how to put a rivet on clothes at home with a minimal set of available tools and materials.

This way you can not only please yourself with a new style, but also avoid buying unnecessary equipment, including an expensive press for installing buttons.