How to drill a stainless steel sink

How to install a faucet into a stainless steel sink

The absence of special holes for faucets or taps in sinks that are produced in our time cannot be called a defect, it is just a necessity.

The fact is that installation technologies for such products require several location options for the sink itself. The modern assortment offers several standard diameters for plumbing fixtures, so it is quite difficult to guess the size in advance.

It’s better not to guess again and not take risks, but to figure out how to make a hole in a stainless steel sink yourself for a mixer.

Types of modern sinks

The two main types of kitchen sinks that are in greatest demand today are stainless steel and ceramic. Manufacturers are in no hurry to make holes in them, placing this work entirely on the shoulders of sellers and end consumers.

Important! If you wish, you can agree directly in the store to drill a hole of the required size. The cost of such manipulation is quite reasonable; all you have to do is indicate the location, diameter, and make payment. As a result, you will receive a finished product with designated places for installing mixers and taps.

It would seem that the problem has been solved, but in practice situations often arise that do not coincide at all with the plans of consumers. For example, when ordering a kitchen of non-standard sizes, or the kitchen equipment itself, if the owner of the house is left-handed, the hole in her new sink is located on the right side, which is incredibly inconvenient for her.

General recommendations for independent work

Before cutting a hole in the sink for the faucet, first install it, take a good look, and only then decide where to make places for the nests. If you still decide to do everything yourself, then use the following useful recommendations:

1. Perform all manipulations with the product immediately before installing it in a permanent location - this will prevent premature damage and deformation of the item.
2. The sink should be installed horizontally on a wooden base, then a hole should be drilled with a special drill.
3. If you use a punch and a hammer, punch a sufficiently fixed bowl manually with special nozzles, previously selected to match the diameter of the holes of the faucet or mixer in the new sink.
4. If you want to use a specially designed punch, please note that it operates using the extrusion method. As a rule, such a device consists of two nozzles and a threaded pin, a pressing washer and a tap. It is enough to replace the pin from the outside, screw on the washer, and perform tightening and pressing.
5. The use of a special drill involves the use of a cone-shaped drill that works according to the simplest principle.
6. When purchasing a mixer with large diameter glasses, it becomes necessary to prepare a special mounting socket. This problem can be solved in two ways - you can order a socket in the store or drill several holes around a circle with a smaller diameter.

How to make a hole in a ceramic sink with your own hands?

Making a hole in a ceramic sink for a faucet yourself is quite simple. The work includes the following stages:

• Make a mark where you want the hole to be, then drill.

Important! This seemingly simple manipulation in practice causes many problems for inexperienced people. Here you cannot use a drill with a pobedit stand, because instead of drilling, it peels or chips the material. A metal drill has proven itself to be excellent here, but it will require a drill with minimal speed, preferably a hand drill.

• Walk the tool several times along the partitions between the holes.

Important! Remember that when drilling, ceramics can heat up quickly, so this must be controlled. It is better to drill with a thin drill and work around the entire perimeter of the future nest.

• Use an electric soldering iron to cut the lines and knock out the plugs with a hammer.
• Cut the material with a jigsaw so that the edges are perfectly smooth.
• Sand the circumference of the socket with a round abrasive pad. If you don't have one on hand, you can use a round file.

Important! Some modern bowls already have special marks on which you just need to hit them accurately with a hammer to make a hole. But it is recommended to do this as carefully as possible so as not to destroy the material.

How to make a hole for a faucet in a stainless steel sink?

There are several proven options for cutting a hole in a sink for a mixer tap made of stainless steel. It is impossible to make such holes in already installed plumbing fixtures, since they may crack due to their support on the countertop. If possible, rent or buy a special cutter to make your job easier.

Prepare the following tools:

• Mounting tape.
• Marker.
• Round file.
• Hammer.
• Kerner.

Instructions for making a hole look like this:

1. Before starting work, the sink should be turned upside down so that all edges rest against the table surface.
2. Make a circle of the required shape and size from mounting tape, attach it to the selected location, and outline it with a marker.
3. Mark the center to make it easier to make a hole with a center punch.
4. Direct the tip of the center punch to the center of a circle made from mounting tape and punch the starting hole with smooth tapping movements.
5. Using a round file, widen the starting hole to the previously marked dimensions.
6. Carefully sand the edges of the cut to obtain an exit of the required diameter.
7. Apply sealant to the edges of the fresh cut.
8. You can install a sink.

material

Now you can handle any material yourself, make a hole exactly in the place where it is convenient for you. All that remains is to carefully study the recommendations and instructions in order to fully imagine and visualize the entire process.

Source: https://ctdim.com/kak-vrezat-smesitel-v-moyku-iz-nerzhaveyki/

How to make a hole for a faucet in a stainless steel sink?

From the author: I am glad to welcome you again, my dear readers! When we renovate a kitchen or bathroom, we are certainly faced with the installation of a sink. For some people, the hole for the faucet in a stainless steel sink becomes a real mystery that is quite difficult to solve. I have repeatedly encountered cases where a person decided on untested methods, thereby simply rendering an expensive product unusable.

One of my friends, who not only did not have special education and skills, but also did not even know how to hold a drill in his hands, decided to make such a hole using a hammer and chisel. Naturally, it turned out to be very crooked, and besides, it was larger than it was necessary. While trying to correct his mistake, he deformed the shell so much that it could not be restored.

Be careful, now I will tell you two ways that will help you solve this problem.

What are the benefits of a stainless steel sink?

I get asked very often why a stainless steel sink is so good. Naturally, installing this item in the bathroom is not aesthetically pleasing, not practical, and generally not entirely normal. To decorate this part of the apartment, it is best to use specimens made of artificial stone.

Installation of the product discussed is more appropriate as part of a kitchen renovation project. An alternative could be a product made from quartz, but not everyone can afford it.

Let us highlight the advantages of steel samples:

• price. The most important thing when performing repair work is rational savings. Yes, if your budget doesn’t bite you and you can afford a more aesthetic product, do it;
• mobility. More than once, even I have encountered moments when a new sink was installed, and the old one was sent to another place for service. For example, to the country house. The issue of removal and re-installation in this case is more convenient;
• reliability. Not every housewife can boast of being careful when working in the kitchen. She can drop something heavy at any moment, and if it is a cast-iron cauldron and it falls on marble, then a crack in the latter is guaranteed. On the steel sink, only a small dent will remain, which can be easily removed with a regular hammer and a wooden block, and the scratches can be covered with special means so that they will not be visible at all;
• it does not need to be embedded into the countertop. This way you can optimize its use and not pay extra when ordering the kitchen itself.

From the above, it becomes clear that a stainless steel sink is the optimal, and most importantly, budget option for the average resident of our country.

Let's use a drill

You can make the necessary hole using a power tool, which every self-respecting owner should have at home. An ordinary electric drill must be equipped with a specialized attachment, which is designed for working on metal. This point is very important, since using a drill with a pobedite tip or diamond coating will simply render it unusable, and there will be no result.

The nozzle is something similar to a compass. If you ask the appropriate question at a construction hypermarket, they will kindly provide you with the necessary product. Let's describe the process step by step.

1. First of all, decide on the place where the mixer will be located. In order to understand whether pouring water will splash onto the walls of the kitchen, simulate the pressure using a filled plastic bottle.
2. Next, you need to create a small hole that will serve as the center point of the cut circle. To do this you will need a metal drill. Arm yourself with it and follow the procedure.
3. Change the nozzle and install it exactly in the place that we created in step No. 2. Before you start drilling, set the desired diameter.
4. Drill a hole.

Just four simple steps solve the problem with a bang!

There is also a special tool that allows you to do the same job, but using your physical strength. It is called "Fixa" and consists of two cylindrical bases connected by a bolt. One of them is sharpened in such a way as to create a standard hole for a faucet.

A little secret

When I worked as a salesperson in a construction hypermarket, the guys from the plumbing department were supposed to provide the service we are talking about for free. However, given that this needs to be done for free, not everyone advertises it. Remember that when purchasing a sink, you can take advantage of the additional functions of a sales assistant!

I am sure that my advice was useful to you, and there will be no problems completing the task!

Source: https://seberemont.ru/otverstie-pod-smesitel-v-mojke-iz-nerzhavejki/

How to drill a hole in a sink or sink? Practical advice

When purchasing a new sink, the question often arises is how to drill the hole. Answers to this and related questions can be found in this article.

How to drill a hole in a ceramic sink

When does the question arise? Sinks without a hole were installed in Soviet bathrooms where there was one faucet for the sink and bathtub. Recently, this option has been used less and less, but sometimes, during budget renovations, apartment owners want to save on buying a new sink.

Sink without tap hole.

And so, you have a sink that has no hole. Working with ceramic sinks may seem like a lot of work, but you can do it if you follow the tips below. It's simple.

You will need:

1. Drill or hammer drill.2. Drill (feather) for ceramics.

3. Crown for ceramics with tungsten carbide coating

Step-by-step instruction

• To prevent the drill from moving, cover the area where you will drill with masking tape.
• We make markings - put a dot with a marker.
• Insert a ceramic drill bit into the drill and start drilling at low speed. Proceed with caution - ceramics are a very fragile material.
• Use a smaller diameter drill first - for example, 6 mm. Then replace it with 8 mm. It is important to constantly cool the drilling site - water it with cold water.
• After drilling the narrow central hole, switch to a bit with a diameter of 30 or 32 mm, depending on the diameter of the mixer.
• Every 2-3 mm, take a thin drill and make small holes in the circle that the crown made. This is done so that the teeth of the crown can engage the edges of the circle and continue working.
• When the hole is ready, you can install the sink in place.

How to drill a hole in artificial stone

Typically, sinks made of artificial stone come with an existing hole for the faucet, but there are options without it, or you need to drill an additional hole for the faucet for the water filter. What to do in such cases?

You can seek professional help, but if you feel confident, you can try drilling the hole yourself. But to do this, it is necessary to determine the material of the product - this determines which tool to use.

So, the options:

• Porcelain tiles
• Agglomerate
• Acrylic stone

Porcelain tiles

The strongest and most durable of the entire group is porcelain stoneware. It serves for a long time and is durable, tolerates temperature and chemical influences well, so it is in great demand. But it is also the most complex material; it is most difficult to make a hole in it than in other types of artificial stone.

The best option for carrying out the work is to choose a crown for porcelain stoneware. It can be supplied as a set with or without a centering drill.

When working with porcelain stoneware, the drilling site should be constantly cooled, and the drill speed should be at the lowest possible speed.

You need to understand which side to drill from and when. If from the front side, after installation, the edges of the hole will be smooth and neat, but there is a danger that the drill will slip and spoil the appearance, for example, scratch or damage the edge.

If from the back, before installation, you are unlikely to damage the bowl, but perhaps the hole will have uneven edges. Basically it's not a big deal because they will be covered by the faucet.

Remember - the further the hole is from the edge of the product, the better. Don’t forget about the bowl so as not to get another, completely unnecessary hole - porcelain stoneware is both a durable and very fragile material. Therefore, the following rules must be observed:

• Before carrying out the process, fix the sink, put chipboard under the bottom, this will protect the work surface.
• Drill exactly perpendicularly, otherwise the drill may damage the glaze.
• To prevent the drill from moving, cover the area where you will drill with masking tape.
• Before work, wet the drill; while drilling, spray the work area with water, for example, from a plastic bottle.

Agglomerate

Milling cutter for working with artificial stone

Agglomerate is a softer material. Usually the sink already has a hole almost drilled. It must be knocked out with a core or drilled with the cutter included with the sink. If the kit does not include a cutter or core, then it is necessary to perform the work with a diamond-coated crown. The instructions are completely identical to the process of drilling porcelain tiles.

Acrylic

The third option is acrylic. If your sink and countertop have color cohesion and create a cohesive space, then it's acrylic stone. This option is not difficult to work with. Ordinary drills are suitable for working with metal or wood.

The diameter of the hole for the mixer is 32-35 mm. It can be drilled with a feather drill for working on wood products. The drill speed should be at medium or low speed. When working with acrylic stone, a lot of chips are formed, and a rather unpleasant odor appears from the plastic heated by the drill.

How to work with a stainless steel sink

Manufacturers often produce stainless steel sinks without the special opening required to install the faucet. As a rule, such sinks are made of durable steel. This sink is very difficult to drill with a regular drill. A diamond-coated crown is barely enough for one hole (after that it will only be scrapped).

We offer for your consideration several options for installing a hole for installing a faucet on a stainless steel sink, although these tips are universal and are suitable for sinks made of ordinary steel.

Option #1

To drill a hole in it, you need to use cobalt drills (or tungsten, but they are more expensive) and a cutter. A cutter, or punch, is a two-part tool. It consists of a die and a knife connected by a bolt.

Before starting work, the sink must be turned upside down. Next, we follow the following procedure:

1. Mark the installation location of the mixer with a pencil or bright marker.2. We make a small dent in the center of the circle so that the drill does not slip off.3. We make an initial hole with a 5-6 mm drill, and enlarge it with a drill of the appropriate diameter to 10 mm.

4. Install the punch (notch) so that the part with a smaller diameter is where the mixer should be. Tighten the bolt until the cutter cuts a hole.

Option No. 2

The second option involves drilling holes only for flexible connections and mounting stud(s). You can use the mixer pressure plate as a template. This option will save you from buying a cutter. But, in any case, you cannot do without cobalt drills.

Option #3

Here's a video as an example:

We hope the article was useful. If you know of other ways to drill holes in a sink or sink, write in the comments.

Source: https://santech-info.ru/santexnika/prosverlit-otverstie-v-rakovine.html

How to make a hole for a faucet in a stainless steel sink: diameter, than

Typically, sinks have a hole for installing a faucet. But there are stainless steel models in which there is no groove. The way out is to make a hole of the required diameter yourself. How to make a hole for a faucet in a stainless steel sink.

Reasons for missing holes

Manufacturers of sinks and plumbing fixtures are trying to standardize the dimensional parameters of models so that they are as compatible as possible with each other. But there is one important circumstance: individual layouts in both the kitchen and bathroom are very popular. To meet such needs, it is necessary to produce sink models in which there is no hole for the faucet. The groove is made independently in the most convenient place and with the necessary characteristics.

There are no holes in metal double-bowl sinks, which by default do not have slots for washing or drying for practical reasons. A person chooses the best option for himself by installing a sink on site.

The size of the holes depends on the design of the tap. Faucet models may vary significantly. The size of the required groove in the sink depends on this.

What matters is: the location of the hot and cold water supply pipes, the design of the fastening mechanisms.

Before performing work, you need to select a model, find out its parameters and design features.

Preparatory activities

Before cutting a hole, you need to do a lot of preparation. First, measurements are taken. The groove must have such a diameter that the mixer can easily pass during installation. There should also be no problems with fixing the tap. The measured diameter is applied at the drilling site. It is important to try everything on, because a mistake will cost a lot.

After marking the area where the groove is made, you need to prepare the workspace and tools. The place where the work will be done must be free and spacious. The sink must be stable and secure. Everything unnecessary needs to be removed.

The hole for the mixer in a stainless steel sink is drilled using a drill and various attachments. Tools needed to drill a hole in the sink for the faucet.

1. Drill.
2. Needle file, file, sandpaper.
3. A small file or cutter for metal.
4. Protective glasses.
5. Brush.
6. Water for cooling.

Drilling bits that can be used to make a hole:

1. an ordinary Pobedit metal drill (preferably with diamond coating);
2. herringbone cone drill;
3. bimetallic hole saw; crown type;
4. Victory hinged drill with a diameter of 28, 30, 32 or 35 mm (size depends on the parameters of the mixer).

Sequencing

The methods by which you can make grooves in a sink depend on the specific tool. You will need some kind of drill bit for a drill. The most affordable way is to make holes with a regular Pobedit metal drill of small diameter: 6, 8, 10 mm.

Sequencing.

1. According to the marking of the circle, several grooves are made around the perimeter.
2. Cooling is carried out periodically using water. Drilling is performed at low speed.
3. The grooves are connected using a metal saw or file.
4. The edges of the hole are processed and leveled with a needle file, file and sandpaper.

How to cut a hole in a sink for a faucet using a bimetallic hole saw.

1. At the required location of the hole, markings are made with a pencil, nail or other improvised object - a circle of the required diameter is drawn with a point in the center.
2. An ordinary Pobedit metal drill of small diameter: 6, 8 or 10 mm is inserted into the drill.
3. A shallow notch is drilled at the marked point in the center of the circle. This will allow the bimetallic hole saw to engage.
4. A hole saw of the required diameter is inserted into the drill. In a specialized store, choosing a crown of the required diameter will not be difficult. Standard sizes are from 28 to 50 mm in increments of 1 or 2 mm, depending on the manufacturer. Well-known manufacturers of hole saws: Banco and Irwin.
5. The crown is carefully placed in a vertical position, so that the central drill goes into the previously made notch. Drilling in progress. To preserve the crown, it is recommended to drill at low speeds. Periodically, chips are removed with a brush, water is spilled to cool the metal and the crown.

The method using a crown is used when making holes in sinks in large quantities. One, with periodic cooling, is enough to drill 1015 slots. Without cooling, the hole saw will fail after 23 holes.

In a similar way, you can drill grooves using a herringbone or a Pobedit articulated drill. After making the groove, the edges are processed. For this purpose, a needle file, a file, and sandpaper are used.

Source: https://vodospec.club/santekhnika/kak-sdelat-otverstie-pod-smesitel-v-mojke-iz-nerzhavejki.html

Hole in stainless steel sink for mixer tap

The absence of special holes for faucets or taps in sinks that are produced in our time cannot be called a defect, it is just a necessity.

The fact is that installation technologies for such products require several location options for the sink itself. The modern assortment offers several standard diameters for plumbing fixtures, so it is quite difficult to guess the size in advance.

It’s better not to guess again and not take risks, but to figure out how to make a hole in a stainless steel sink yourself for a mixer.

How to cut a hole in different types of sinks

The lack of holes for taps or mixers in modern sinks is not a defect, but a necessity. Installation technologies for such products require several positions for the sink itself.

The product line offers several basic diameters for plumbing fixtures - try to guess which one is needed here! We won’t guess, we’ll install it.

Photo is a problem that we have to solve.

Two types of sinks

The most popular types of kitchen sinks now are:

• Stainless steel sinks;
• Porcelain stoneware products.

With both stainless steel and porcelain stoneware, manufacturers are in no hurry to drill holes, leaving these little details to the sellers.

The sinks are different, and so are the appliances.

Please note! In sink sales stores you can arrange for holes to be drilled.

The price of the manipulation is negotiable, you indicate the diameter and location, pay and receive the finished product with places for installing taps and mixers.

The problem has been solved, and this topic can be closed, but there are situations that radically change the original plans. Moreover, the desire to do everything with your own hands, and the pleasure that you get from a job well done, is incomparable.

Independent work

Simple things can change the world. The initial desire to install the tap on the right side in the corner will be nullified if your wife is left-handed.

Note! In the kitchen, like nowhere else, great importance is paid to beauty, functionality, and also ergonomics. It is very inconvenient for left-handed people to open the tap on the right with their left hand.

Water gets on your hand.

You can press out a hole.

We recommend placing the sink in place first, taking a closer look, and then deciding and selecting nest locations. Have you decided to do the work yourself?

Our instructions:

1. Carry out all work on the product before installing it in a permanent location; with these simple steps you will prevent deformation of the item and premature damage;
2. Place the sink horizontally on a wooden base. Drill a small hole with a metal drill, enough 5-6 mm to locate the center of the circle;

Advice!
If you use punches and a hammer, then the above manipulation is not necessary.

Carrot drills and their capabilities.

1. And then there are three paths to choose from:

• Hammer and punch. Here you simply pierce the fixed bowl with special nozzles manually, the nozzle is initially selected to match the diameter of the hole in the sink for the mixer or tap;
• Punch of special design. This is a mechanical toy that uses the extrusion method. Such a punch consists of a threaded pin and two nozzles, a tap and a pressing washer with a wrench head. By installing the pin into the hole from the outside, screwing on the washer with the head, you use a wrench to tighten and press. The result of this manipulation is a hole in the stainless steel sink for the mixer;
• The third way is a special drill called a carrot. The name has taken root so much that even on the factory packaging of the product it is not called anything other than a carrot drill. The drill is presented as a cone, with a cutting edge diameter from 6 to 32 and even 38 mm. We will not describe the principle of using a drill, everything is clear.

Punchers included.

In the piggy bank! Sometimes the consumer's choice is on faucets with glasses of large diameter. A siphon for a sink with a large hole requires a large seat. Then there are several options: the first is to order a hole in the store, the second is to drill several holes of a smaller diameter around the circumference. Then simply connect them together, removing the inner circle with a chisel.

True, accuracy and precision of movements will be required.

How to drill a hole in a stainless steel sink - we've sorted it out, let's move on to the stones.

Stone and under stone

Much more interesting is the topic of drilling landing sockets in stone sinks.

What are we doing?

• At the location of the proposed hole, we make a mark and drill;

Please note! A simple manipulation - working with a drill - is not very simple in practice. A drill with a pobedit insert is contraindicated for this work, it does not drill so much as chips, peels the material. The drill for metal has shown itself to be quite good, but low speeds of the drill itself are required ( Ideally, it is better to use a hand drill).

At high speeds, the edges melt.

We work at low speeds.

• During the drilling process, the material can heat up quickly, but this is difficult to control. It is better to drill a hole in a sink made of artificial stone with a thin drill. We work around the perimeter of the entire future nest;
• It is recommended to “pass” the partitions between the holes in two ways:
• We cut the strokes with an electric soldering iron, followed by knocking out the plug with a hammer;
• The material is cut well with a jigsaw. Although this process takes longer, the edge is the smoothest;
• Grinding the hole circumference is done using a round abrasive attachment for the entire circumference. If you don’t have one on your farm, use a regular round file.

Crowns coated with diamond are rare guests on the farm.

To the piggy bank!
You can also drill a hole in an artificial stone sink with a diamond drill, if you have one.

We inform you! In some bowls there are special marks. These are places where, by striking accurately with a hammer, you can punch a hole. This must be done with caution; the marks themselves are marked with paper stickers, which can slide off during transportation.

A blow to another point can only lead to destruction of the material.

Quality work is the key to longevity.

We have covered the topic of how to cut a hole in a sink for a faucet. All that remains is to watch the video in this article to visualize and fully present the process. However, if you are not sure of the result, it is better to contact specialists.

Source: https://gidroguru.com/vnutrennyaya-kanal/santeh-pribory/mojki/2345-kak-prorezat-otverstie-v-mojke

How to install a stainless steel sink?

It so happened that we were faced with the need to install a sink. For various reasons - it has lost its attractive appearance, is outdated, damaged, etc.

How difficult is it to install a sink yourself without involving expensive professionals? Let's figure it out.

How to choose a stainless steel sink

So, having looked through the options for sinks made from various materials, you have chosen stainless steel sinks. How to choose what you need from a huge range of models?

It's not difficult at all. There are two types of sinks:

If you have a built-in kitchen set with a monolithic countertop, then, of course, you need a built-in sink. Overlays are used in small kitchens, where installing built-in furniture is impractical and expensive.

According to the shape, the sink is divided into:

• Classic (regular, rectangular);
• Round and oval;
• With two or more bowls.

For corner placement of sinks, round or, for example, radially rounded sinks are suitable.

The surface texture can be polished or matte. It is important to remember that for all the beauty of a glossy sink, it requires additional attention.

All droplets and scratches are perfectly visible on the surface, so you need to handle it very carefully and wipe it after each use so that there are no traces of water left.

Have you decided what shape and texture you like? Now the most important thing is to make sure the quality of the steel from which the sink is made. The easiest way to understand this is if you choose a sink from a well-known manufacturer, or on the recommendation of professionals, friends, or acquaintances.

How to fix a stainless steel sink

So, the sink has been purchased, delivered home, and here the question arises - how to install and secure it?!

If you have a countertop sink, there are no problems - the dimensions are standardized, the old cabinet fits perfectly under the sink, the fastenings are universal and you just need to read the instructions to handle the fastening yourself.

What if you have a monolithic countertop and your “new thing” doesn’t want to coincide with the hole for the old sink?! No problem. A drawing with mounting dimensions is included with each sink. What tools will you need to install the sink:

• Electric jigsaw with files;
• Hand drill-driver;
• Drill diameter 10 mm;
• Transparent silicone sealant;
• Pencil, ruler, pattern.

We mark the shape of the future hole according to the dimensions in the drawing using a ruler and, if necessary, a pattern.

To start working with a jigsaw, you need to drill a hole near the sawing line into which the file goes. We carefully cut out a hole along the contour and remove the sawn part.

All that remains is to install the sink in place! Apply silicone sealant to the countertop along the contour of the sink, install the sink bowl, mount the fasteners that are included in the kit, press and remove the remaining sealant.

All! Wait, you wanted to install a tap for a drinking water filter in the sink, but there is no hole in the sink! What to do, how to drill through metal?

How to drill a stainless steel sink

In order to make a hole in a sink for a tap, home craftsmen use various tricks:

• Drill a perforation along the contour of a large hole with a thin drill, then cut out and file the edges of the hole;
• They cut out with a thin chisel (not always accurately and accurately);
• Using a drill with a Pobedit tip, drill a hole of large diameter at once (there is a risk of not being able to cope with the drill, since the force applied is very large).

The easiest way is to use a carbide core drill. They come in diameters from 12 to 150 mm. The drill is a hollow tube with a thin so-called pilot drill in the center.

Drilling technology is extremely simple! We mark the desired location with a punch, set the tip of the pilot drill and full speed ahead!

The pilot drill, having made a small hole, is pulled into the drill mechanism using a spring, and the crown continues the intended movement exactly in the given place, without slipping or tearing the drill out of your hands.

The hole is perfectly smooth, without burrs or scratches, and does not require additional processing. We install the faucet and enjoy the work done!

Source: http://stroybud.com/kak-ustanovit-moyku-iz-nerzhaveyki/

How to drill a stainless steel sink for a tap

Stainless steel is widely used in household and industrial applications to create various items due to its significant number of positive qualities. It is an alloy of various materials that give stainless steel resistance to corrosion and aggressive environments. Based on their percentage, it is possible to create different types of material in the alloy.

At home, items made from so-called food-grade stainless steel are often used, such as taps and mixers, sinks and sinks in the kitchen, tableware and other things. Therefore, it is often necessary to drill through stainless steel for some purpose. However, you should prepare for the process. That is, study the recommendations of more experienced craftsmen if the procedure is being performed with your own hands for the first time, and also select suitable drills and lubricants.

In addition to experience, you will need a bit of sensitivity and attentiveness. This is far from the only thing a master needs. What helps most when drilling is lubricating fluid, without which the master risks damaging the drills and the material. The lubricant consists of machine oil and sulfur, so it is easily recognized by its viscous form and increased fat content. In addition to choosing the right material, you need to know some features of how to drill a hole in stainless steel.

Nuances when drilling

What needs to be done is to decide on a tool. What exactly to use depends on the diameter of the holes needed. If up to 12 mm, then at home you can use a hand drill.

Nothing else will help you drill holes in stainless steel as efficiently as preliminary marking. It is especially effective when making single holes or processing hardened and sheet metal. Axial marks are applied to the workpiece under the drill, and then a small recess is made in the product. Later they are deepened to the required size.

A template is another thing that will help save time when drilling, because the contours of the holes are pre-marked on it. Craftsmen have to resort to tricks when the work is done from the edge of the surface. Usually, half-holes are needed here, which are made as follows: a plate of the same material is attached to the workpiece, which is clamped in a vice. After which you can drill out a standard recess, and upon completion of the work, simply remove the attached plate.

Useful drilling techniques

Every master who has gotten his hands on this business has a couple of clever tricks that greatly simplify the drilling process. Many videos and photos on the site will clearly demonstrate what needs to be done and how.

First of all, you should pay attention to the plane in which the working surface is located. When you need to drill a hole in a horizontal object, coolant is poured into a small plug through which the drilling is carried out.

If the structure is installed vertically, then a paraffin ball is attached to the site of the future hole. Thanks to this trick, you can quickly get the job done even in the most inconvenient places.

Another important nuance to remember when planning to drill stainless steel is to set the drill to minimum speed. To obtain standard holes, a speed of up to 150 revolutions is sufficient. If the speed is too high, the lubricant simply will not have time to cool the drill.

What to do with equipment that does not have a speed switch? Press the “Start” button and release after 1-2 seconds. If you work with such short presses, the drill motor will not develop high speed.

If you have to drill a lot and often into stainless steel, you should buy a special stand for the drill. Financially, the expenses will be small, and the process will be significantly simplified.

You can determine that the drill is dull or the material is overheated by the darkening of the chips. Therefore, skilled craftsmen first use small-diameter drills, for example, a four-piece. Then the hole is brought to the desired size, obtaining smooth and neat edges.

This is especially important when drilling stainless pipes. In this case, an ideal result can only be achieved using a special stepped cone drill.

When it is necessary to make a hole of a large diameter, from about 15 millimeters, a crown hole is used, in other words, a crown.

Use of lubricants

To prevent the procedure from ending in failure, you need to use cooling materials. The thing is that stainless steel has high viscosity. During operation, the load falls simultaneously on the drill and the material, as a result of which overheating of either one or the other may occur. Therefore, it is so important to consider how to cool the instrument.

When you have to drill a lot, it makes more sense to attach an automatic supply of lubricants to the machine. If drilling is a single and rare case, then the drills are processed immediately before drilling. A mixture of machine oil and sulfur is used as a lubricant. In this case, sulfur can be taken both colloidal and for fumigation, well known as “sulfur color”.

If it was purchased in powder form, then the substance is simply mixed with machine oil. When the sulfur is lumpy, it still needs to be ground. An effective cooling lubricant is a mixture of sulfur and fatty acids, which can be obtained at home from ordinary laundry soap.

To do this, perform the following steps:

• a bar of soap is rubbed, and the resulting mass is poured with hot water;
• technical hydrochloric acid is carefully poured into the soap solution;
• when fatty acids float to the surface, pour in cold water;
• wait until they harden and remove the top layer.

When creating a cooling material, fatty acids and sulfur are taken in a 6:1 ratio. The effort and time spent are justified, because this composition will help drill through even the thickest stainless steel.

Drill selection

Choosing a reliable drill is an important step when preparing for drilling. On sale you can find foreign tools manufactured according to the DIN-338 standard and marked HSS-CO. It makes it clear that the composition contains at least 5% cobalt, as in old Soviet drills. You can recognize a stainless steel product by its obtuse sharpening angle, which makes alignment easier when starting work. Such a tool is easy to obtain in any specialized store at an affordable price.

As for carbide tools, they are suitable for processing stainless surfaces and products made from this material. But problems may arise with its purchase, since such drills are not available in every hardware store, plus they are much more expensive.

When choosing tools, you should purchase only high-strength products. You can look for old cobalt drills, which are still considered the best.

If you fail, then you should stick to products from Ruko, Bosch, Gross, Hilti, which are available in most stores. The price depends on the diameter, for example, a 3 mm tool can be bought for about 100 rubles. The larger the diameter, the higher the price.

It will not be difficult for real craftsmen to adjust the angle of a conventional drill if they have a diamond wheel at home.

Source: https://stroyka.ahuman.ru/chem-prosverlit-nerzhavejku-mojku-pod-kran/

Finally

We have covered the topic of how to cut a hole in a sink for a faucet. All that remains is to watch the video in this article to visualize and fully present the process. However, if you are not sure of the result, it is better to contact specialists.

Source: https://placeclean.ru/otverstie-v-mojke-iz-nerzhavejki-pod-smesitel.html

How to drill a stainless steel sink for a tap?

Typically, sinks have a hole for installing a faucet. But there are stainless steel models in which there is no groove. The way out is to make a hole of the required diameter yourself. How to make a hole for a faucet in a stainless steel sink.

How to drill a hole in a stainless steel sink for a faucet?

» Other »

Question for experts: What and how to drill a hole in a stainless sink for a faucet.

Best regards, Ivan Grafov

Best answers

crown of the appropriate size.

draw a circle under the mixer. Using a small drill, we drill in a circle.

The cutter is special, the cost is about 180 rubles, first we use a drill, then we expand it with a cutter inserted into the drill to the required diameter, be careful, it cuts metal very quickly so don’t get carried away.

Previously, holes were made in a circle by increasing the diameter of the drill and then using a file. Now there are many ways: 1. There are special drills in the form of a crown, for centering the drill in the middle, made of a special alloy. The base is common, the crowns vary depending on the diameter. Ask the store where they sell the tool.

2. There is a special press consisting of two halves, one with sharp, uneven teeth and enters the second with a bolt. We drill a 10mm hole, insert a bolt and tighten the two halves with a wrench. The result is a smooth, precise hole. These items are included in the IKEA kitchen furniture set. She gave me a daughter and I just work for her.

Using a narrow chisel (I use a 10-12 drill bit) just place a piece of wood under the bottom, for example. It breaks through easily.

I did this with a sharp pobedit drill. A regular metal drill will not take stainless steel.

Usually such holes are made right at the point of sale using a special press, but in practice it was necessary to cut the hole with a knife, such as a shoemaker’s knife made from rapid.

Drills are sold specifically for drilling stainless steel (by the way, there are also cutting wheels specifically for stainless steel). Draw a circle on the sink with a felt-tip pen, drill holes along the line (placing a board under the bottom), then use a narrow chisel to cut out along the drilled holes and finally clean it with sandpaper wound on a round stick (a piece of a mop handle).

answer

This video will help you figure it out

Answers from experts

Use a small drill in a circle, and then break it out... mark exactly. and clean it with a file.

Take several drills, they will become dull and may even break.

Wow, I drew a circle (to size), placed a piece of wood, drilled (with a thin drill) small holes along the contour, sharpened it with a file. IMHO.

Buy a feather that is the right size for the tree, just drill once and that’s it. This is the only way to take thin stainless steel. I drilled holes in barrels for heating elements when there was nothing. To make it easier, drill a small hole in the middle for the guide.

And IKEA sells special drills for this.

Step drills for sale (like a Christmas tree). They do everything. Take in 45mm increments.

with a metal crown, it couldn’t be easier

Step drills for metal, see photo

Mark the hole, then use a core punch around the perimeter to make small notches often so that the drill does not move or jump out, then drill with a 3-4 mm drill around the perimeter, then you can trim it with a round file.

Plumbing stores have a special tool for cutting holes..

Where you bought the sink, you are required to make a hole for free.

Crown cutter for metal, any sizes.

Stainless steel sinks are available left and right according to the location of the bowl. But many manufacturers produce universal sinks (without a hole for the mixer), for which, during the kitchen manufacturing process, it is necessary to additionally make a hole with a diameter of 35 mm for the mixer. For these purposes, there are special devices: punches or, in other words, die-cuts:

Their operating principle is based on a pair: punch - matrix. Having punched or pre-drilled a hole, a rod is inserted, along which, using a key or gate, the punch presses the hole, entering the matrix.

It should be said that it is necessary to purchase a device made of high-quality (well-hardened) materials. The approximate cost of such a kit (top photo) ranges from $10-80 depending on the manufacturer.

Hole making services usually cost between $1-3.

One of my friends bought such a die cutter at a hardware store, made a hole in the sink with its help, and returned the die cutter to the store.

Good luck!

This is what the die cut assembly looks like

at home using a drill and file

Is it better to have a round or semi-circular file?

Drill and metal bit of appropriate diameter.
5 minutes business.))))))

Source: https://dom-voprosov.ru/prochee/chem-prosverlit-otverstie-v-mojke-iz-nerzhavejki-pod-smesitel

The diameter of the hole in the sink for the mixer, what to do

In recent years, the assortment of stores has been expanded with sinks of symmetrical shapes. This is very convenient, since there is no fundamental difference in how to install them - on the right or left side.

The manufacturer assumes that the hole for the mixer will be made independently at the time of installing the sink. In fact, it is logical and convenient. It is often not always possible to purchase a sink with pre-made outlets, since the parameters of the mixers are different.

Most kitchen sinks are factory-prepared to have an outlet of 32 millimeters, but commercially available faucets often have a diameter larger than 34 millimeters. Shops are supplied with sinks without a pre-drilled hole, made of stainless steel and ceramics. Most consumers are faced with the almost impossible task of making a hole of the required diameter. However, not everything is so sad.

How to make a hole for a faucet in different sinks

Before you start drilling the sink, you need to make sure that everything you need is on hand. The following may be needed:

• drill for ceramics;
• tungsten carbide crown;
• perforator;
• marker;
• sandpaper.

The crown should be taken with a diameter of 33 millimeters. It is better to drill with a hammer drill rather than a regular drill. And the point here is not the force of the hammer blow; moreover, its striking abilities should not even be used. It’s just that the rotation of the rotary hammer is slower, but it weighs more than a drill, and it will be more powerful. Of course, if there is no hammer drill, then you will have to use a drill, but you will need to set the minimum rotation speed, otherwise the crown will not bring any benefit.

You should start, naturally, with markings. It is logical that you first need to decide where exactly the mixer will be located. Having determined the installation location, you need to mark it with a marker.

Having installed a drill bit for working on ceramics in the hammer drill chuck, you should start working. The hole must be through. We made it solely so that we could install the drill from the crown.

Reference. It should be understood that the strength of ceramics is very high. In terms of strength, it can be compared with porcelain stoneware. If you have ever dealt with this material at least once in your life, you can imagine it. Despite the strength of porcelain stoneware, it is very fragile.

The first step is to make a narrow hole, which is then widened. First, a six-millimeter drill is used, then you can use an eight or ten millimeter drill.

When working with a drill on ceramics, you should remember that the drilling site must be continuously moistened with cold water. You can just pour it from the bottle.

Once the center hole is made, it is time for the crown. It will be very easy to get through the initial two or three millimeters, but then difficulties may begin. Most likely, the crown will simply rotate, without any noticeable indentation.

To facilitate the advancement of the crown, you need to help it a little. Everything is very simple. Using a thin ceramic drill, we make shallow drills inside the selected recess. This will allow the crown to move more easily, since there is a stop. After the crown goes deep and stops again, the indentations should be made again.

What should be the diameter of the hole for the mixer?

If we focus on the existing standard, it should be noted that siphons that are installed under the sink are rarely more than thirty-five millimeters in diameter. If the sink already has a hole for the faucet, then, most likely, all questions will disappear by themselves, since it should fit.

But some companies have models of sinks, usually made of ceramics, which do not have holes for the mixer at all. The fact is that there are faucets that are mounted either on the side or on the wall above the sink. This raises the question of how easier it is to drill a hole. However, if you have a drill, the necessary drill bits and minimal operating skills, this will not become an insoluble problem.

If you use a crown with a diamond core, for example, with the same thirty-five millimeter diameter, you can easily make the required hole. In this case, there is no need to somehow cool the drill or pour water. With modern equipment, none of this is needed. With such a crown it will be possible to make a perfectly even hole, without any chips.

Once the hole is ready, you will need to think about sealing. You will need to lay a gasket on the sink, and when the mixer is installed in its place, it will be useful to treat the joints with silicone sealant. This will eliminate any possible leakage.

How to make a hole for a faucet

If you are careful and careful, drilling into a ceramic sink is not that difficult. This is done as follows:

1. A mark is drawn at the place where the mixer will be located. This is where you need to drill. Making a hole is a very simple task at first glance, but it raises many questions, especially for those who are faced with this for the first time. Under no circumstances should you use a drill with a pobedit tip. It does not drill, but simply chips the material and peels it. It is better to use a metal drill at low speeds, or maybe even a hand drill.
2. Next, holes are made in the partitions. The impact of the drill leads to strong heating of the ceramics; this heating must be strictly controlled. To work, you need to use a thin drill and work around the entire perimeter of the future nest.
3. Using a soldering iron, you need to make notches, after which you can knock out the plug with a hammer.
4. You need to go along the edges of the chip with a jigsaw and a diamond file to trim the hole.
5. The edges of the hole must be treated with an abrasive nozzle. If you don’t have one on your farm, you can also use a round file.

On some models of ceramic sinks, manufacturers specially make special marks. If you hit them accurately with a hammer, they can be easily knocked out. This creates a finished hole for the mixer. The main thing is to hit carefully.

Subscribe to our Social networks

Source: https://setafi.com/mojka/kakoj-diametr-otverstiya-v-mojke-pod-smesitel/