How many bars of 18 reinforcement are in a ton

A1 fittings - table of weights and assortment according to GOST 5781-82

A1 reinforcement is a type of rolled steel with a round cross-section and a smooth surface. Produced in accordance with the requirements of GOST 5781-82 using hot rolling technology. The main areas of application are the production of reinforcement frames, mounting loops for reinforced concrete structures, plaster nets, enclosures, fences, for the installation of permanent formwork, reinforcement of plaster layers and floor screeds.

Characteristics

In the production of these products, St3 of various degrees of deoxidation is used - boiling, semi-calm, calm. Products made from completely deoxidized steel (calm) are used in critical structures designed to withstand high loads. Rolled products can be heat-strengthened (T) or stretch-strengthened (B).

Main physical characteristics:

yield strength – 235 N/mm2;
temporary tensile strength – 373 N/mm2;
relative elongation – no less than 25%.

Performance properties of steel reinforcement A1 (A240):

Good weldability due to low carbon steel construction.
Environmental friendliness. These products have safety certificates indicating their compliance with regulatory requirements.
Possibility of bending at the angle necessary to create a structure.
Low resistance to corrosion. Increased by painting, galvanizing, aluminum zinc plating.
Lower cost compared to periodic profile reinforcement.

Assortment of fittings A1

According to regulatory documentation, products are produced in the diameter range of 6-40 mm. It goes on sale in coils - up to 10 mm in diameter - or rods 6-12 mm long. The weight of products can be determined by the formula M = ρ* l*(π*d2)/4 , in which:

M – product mass, kg;

ρ – average steel density, taken equal to 7850 kg/m3;

π – 3.14;

d – cross-sectional diameter, m;

l – length, m.

Another option for calculating the mass of a batch of reinforcement is using a table from which the mass of 1 m is determined, and then this value is multiplied by the total footage of the batch.

Weight table for 1 m reinforcement A1

Diameter, mm	Cross-sectional area, cm2	Weight 1 m, kg	Number of meters per ton	Diameter, mm	Cross-sectional area, cm2	Weight 1 m, kg	Number of meters per ton
6	0,283	0,222	4505	20	3,14	2,47	405
8	0,503	0,395	2532	22	3,8	2,98	336
10	0,785	0,617	1620	25	4,91	3,85	260
12	1,131	0,888	1126	28	6,16	4,83	207
14	1,54	1,21	826	32	8,04	6,31	158
16	2,01	1,58	633	36	10,18	7,99	125
18	2,54	2,0	500	40	12,57	9,87	101

Source: https://TreydMetall.ru/info/armatura-a1-tab-vesov

Types of reinforcing bars and their main characteristics. Reinforcement weight table

Construction fittings (rolled reinforcement or rolled metal) is a metal rod of a certain diameter and length, made from steel of various grades in accordance with the requirements of the standard.

In the Russian Federation, the document regulating the amount of reinforcing steel in reinforced concrete structures is SP-52-101-2003 and GOST-57-81-82.

For the common man, the weight of reinforcement can be determined using special tables located in these standards, as well as in construction reference books.

Basic design requirements for reinforced concrete structures. Weight of size 12 fittings

In order for reinforced concrete structures used for the construction of individual residential buildings to be reliable and durable, designers and builders must follow a number of basic rules. These rules govern the use of reinforcement in various reinforced concrete structures:

For beams. The minimum diameter of longitudinal working metal products in reinforced concrete floor and roof beams, lintels and girders must be at least 12 mm, the maximum diameter is no more than 32 mm, the optimal diameter of reinforcing bars in reinforced concrete beams is 12-20 mm.
For columns. In reinforced concrete columns, the minimum permissible diameter of the longitudinal working reinforcing bars is 14 mm, the maximum is 36 mm. The minimum number of working rods in a column is 4 pcs. The specific gravity of reinforcement in a reinforced concrete column should be less than 10% (and in beams - 8%).
For foundations. In reinforced concrete foundations, the smallest diameter of working reinforcement should be 10 mm. Maximum – not limited. The most common diameters of reinforcing bars in the construction of individual houses are 10-16 mm.

The reinforcement can be wire (3-6 mm in diameter) and rod (8-40 mm in diameter). Rod reinforcement is also called flexible. In particularly loaded and critical structures, rigid metal products (rails, angles, I-beams, pipes) are used.

Reinforcement 12, whose weight is insignificant, has proven itself best in reinforced concrete structures. It is believed that measured reinforcing bars are more effective when laying concrete. Reinforcement 12 with a weight of 888 grams per meter can be produced in rods with a factory length of 11.48 m. This will reduce welding costs (when welding rods).

reinforcement weight table

A few words about the available reinforcement weight tables

According to GOST-57-81-82, the profile number, the weight of the reinforcing steel, as well as its cross-sectional area and maximum mass deviations must comply with Table 1 given on our website. Experts have also developed numerous reference books on rolled metal products.

Some of them indicate the chemical composition and properties of rolled products, the level of weldability and hardening, and the weight of 1 meter. Useful for storekeepers and suppliers is a directory of various types of metal, where several pages are occupied by tables of reinforcement weights.

By the weight of 1 m of reinforcement, you can determine the need for tonnage and, conversely, how many meters of reinforcement are per ton of this rolled product.

The weight of 1 m of reinforcement affects the total tonnage of the batch

In rolled metal, calculations are mainly carried out in tons or kilograms. Metal suppliers are well aware of the reinforcement weight tables. Guided by them and the need for meters, they order the required quantity in tons. It is advisable to order a batch of metal equal to the weight of the bundle formed at the factory.

THIS IS INTERESTING: How to use the Apollo knife sharpener

Managers and storekeepers are familiar with how much one shipment weighs and will inform the consumer about this. For example, when receiving reinforcement 12th, weighing 3 tons, it is recommended to pay and purchase 3200 kg or 2800 kg of this rolled product, so as not to tear the existing packaged packs.

Of course, if the customer absolutely needs 3 tons, and no less and no more, then a few free rods from the torn packaging can be added to the finished package of 2.8 tons. But during transportation, such a loose and relatively light rental can simply be lost, or part of it can be pulled out in the parking lot.

Based on the fact that the weight of 1 m of 12th reinforcement is 888 grams, one 9-meter rod of such metal products weighs about 8 kilograms. It can be easily lifted by an ordinary man.

For the finished batch of 2.8 tons of reinforcing bars, the warehouse will provide another 25 bars. They must be additionally packaged, tied with binding wire. Typically, experienced suppliers and delivery managers prefer to deal with packaged rolled metal products. If there is a discrepancy in weight indicators, the customer will be refunded, and if there is an excess of metal supplied, which is allowed in rare cases, the customer must pay extra.

When working with metal, you should remember that metal is not sausage, you can’t just cut a couple of kilograms from it. Although, with the current high cost of rolled metal, many wholesale metal warehouses and stores provide metal cutting for an additional fee. But such a procedure is not always justified. Construction reinforcement is not exactly a metal that requires cutting.

The cost of the weight of 1 m of reinforcement will be approximately equal to the cost of cutting, which is neither rational nor effective.

The use of various classes of reinforcement in construction

The class of reinforced metal products is one of the main indicators of its quality (tensile strength). The classes are designated A and B. These categories must meet all existing standards and requirements (yield strength, weldability, ductility, cold resistance, etc.).

In the construction of reinforced concrete structures, smooth rolled metal of class A 240 is used. Also in the construction of reinforced concrete structures, classes A 300, A 400, A 500, B 500 can be used, which refer to a periodic profile (reinforcement with characteristic transverse protrusions and longitudinal ribs).

Depending on the type and physical properties of reinforcing steel, it is used for:

construction of reinforced concrete structures
laying foundations and strengthening concrete structures;
production of reinforcing mesh;
construction of frames, fences, etc.

Source: https://papamaster.su/vidy-armaturnogo-prokata-i-tablica-vesov-armatury/

Weight table for plastic fittings

Today on the market you can find both outdated steel reinforcement with a diameter of 6 to 80 mm, and new modern composite reinforcement made from the following materials: basalt plastic and fiberglass.

Metal products are highly susceptible to corrosion, rust and other chemical processes; they are heavy and not always convenient to transport.

But composite reinforcement is not subject to either physical or chemical influences, it is quite durable and much less is required compared to steel reinforcement.

As a result, the cost of construction where non-metallic reinforcement is used is significantly reduced (you can compare the price of plastic reinforcement with the price of metal reinforcement here). Therefore, using ASC for the construction of concrete structures is reasonable and profitable.

Many people know that when calculating the required amount of material for reinforcing concrete buildings and structures, it is necessary to use the equality of loads applied to all reinforcing elements. Replacing conventional steel reinforcement with a new composite material involves selecting a profile of fiberglass or basalt-plastic reinforcement. The profile must be of such a diameter that its strength is equal to the strength of conventional steel reinforcement of a given diameter.

Table of correspondence between the diameters of plastic reinforcement and steel reinforcement of class A3 (A400C) when replacing:

Steel reinforcement A3 (A400C), diameter	Plastic fittings, diameter
6 mm	4 mm
8 mm	6 mm
10 mm	8 mm
12 mm	8 mm
14 mm	10 mm
16 mm	12 mm
18 mm	14 mm
20 mm	16 mm
22 mm	18 mm
25 mm	20 mm

This table shows the weight of plastic reinforcement and steel reinforcement:

Reinforcement diameter	Weight of one linear meter of steel reinforcement (according to GOST 5781-82)	Weight of one linear meter of composite fiberglass reinforcement
6 mm	0.222 kg	0.049 kg
8 mm	0.503 kg	0.082 kg
10 mm	0.785 kg	0.134 kg
12 mm	1.131 kg	0.185 kg
14 mm	1.21 kg	0.276 kg
16 mm	1.58 kg	0.352 kg
18 mm	2.0 kg	0.44 kg

From the tables above it is clear that using plastic reinforcement is much more profitable than ordinary steel.

Return to list

Source: https://izh-reduktor.ru/about/art/article/tablica-vesov-plastikovoj-armatury.html

Purchase of fittings

The MosVtorLom company provides services for the acceptance and purchase of rebar for scrap in Moscow and the Moscow region. At the request of the customer, our teams of specialists dismantle the building and foundation and then accept the reinforcement. A service for dismantling and removal of prefabricated metal structures is available. We have our own fleet of vehicles and special equipment.

The company works with legal entities and individuals. We constantly offer favorable and flexible price offers to our customers and offer convenient payment methods.

Acceptance of fittings up to 14,000 rubles. per ton. Call!

(916)562-80-36
(915)464-44-18

Free removal throughout Moscow and Moscow Region. Free dismantling!

What kind of fittings can be scrapped?

The company accepts reinforcement of any class and name, including A3 (A400) class reinforcement used in construction. We buy metal in any condition:

new reinforcement that remained unclaimed during construction and other work;
stale rolled metal that has not been used;
construction scraps, bulk scrap;
corrugated and shut-off valves;
defective metal parts with deformation and damage.

THIS IS INTERESTING: How to properly sharpen knives for a meat grinder

The company also accepts steel ropes, binding wire for reinforcement, metal rods, and buys mixed waste.

Reinforcement is accepted without taking into account its purpose, corrosion resistance, or use in a welded structure. The volume of the delivered fittings is unlimited.

Still have questions?
Order a reinforcement cost estimate and consultation for free!

Purchase of fittings, price as of 01/21/2020

Reinforcement class Clogged Diameter, mm Cost, rub. for 1 kg

up to 500 kg	500 – 5000 kg	More than 5000 kg
A-2	not less than 5%	10—80	11	12	13
A-3	6—40	11	12	13
A-4	10—22	11	13	14
A-5	11	13	14
AT-4	10—40	11	13	14
AT-5	11	14	15
AT-6	10—32	11	14	15
AT-7	11	14	15
Trimmings	—	Negotiable
Metal waste	—	Call

The price of scrap reinforcement depends on the grade of metal, the percentage of impurities it contains, the need for preliminary dismantling (including cutting), the presence of significant damage and contamination (rust, paint, etc.). The cost is also affected by the total volume of the reinforcement batch: the larger the batch, the higher the price for each kilogram.

Source: https://lomvtormetalla.ru/uslugi/skupka-armatury/

How many rebar bars are there in a ton 14

Aluminium, duralumin
Copper, bronze, brass
Tin
Lead
Zinc

I recently got married and am now busy, so to speak, arranging my nest. But really, how many meters are there in 1 ton of 14 mm reinforcement? Do you want to buy high-quality fittings at a competitive price and in any volume? The specialized company Iron City offers a wide range of products. Diameter 8 millimeters - 0.395 kilograms. How many kg are in 1m of reinforcement?

Hello, my name is Angelina. Diameter 6 millimeters - 0.222 kilograms. How many meters are in 1 ton of reinforcement with a diameter of 14 mm. Therefore, we provide an extract from the table, from which you can immediately find out how many meters of reinforcement with a diameter of 14 mm are in 1 ton. Weight and number of meters in the fittings.

With a diameter of 18 millimeters - 500 meters in 1 ton. You have calculated exactly how many meters of reinforcement with a diameter of 14 mm will be needed at your site, you come to the metal depot to buy reinforcing steel and then it turns out that the price list or price list for the sale of reinforcement with a diameter of 14 mm is compiled in tons.

You can, of course, arm yourself with a calculator and make calculations using the formula. With a diameter of 12 millimeters - 1126 meters in one ton. With a diameter of 16 millimeters - 633 meters in one ton. However, such a reference table for reinforcement, the weight of reinforcing steel and the number of meters in tone is not always “at hand”.

It is much more reasonable to find out how many meters are in 1 ton of reinforcement with a diameter of 14 mm, using the reference data from the table for reinforcing steels. With a diameter of 24 millimeters - 260 meters in one ton. The fact is that, technically, it is more logical to do all calculations for construction based on the number of meters of reinforcement.

How much does a meter of reinforcement 10 and other diameters weigh? Several factors influence the weight of reinforcement. How many meters of reinforcement in a ton? GOST 5781 provides the following data: Reinforcement with a diameter of 5 millimeters - has 5347 meters in one ton. A contradiction arises.

In order to calculate the mass of the reinforcement, you need to add the length of the reinforcement bars and multiply by the mass of the linear meter. Most people ask questions such as: How many meters of reinforcement in a ton. They will help you calculate the required amount of reinforcement to create both strip and slab foundations.

With a diameter of 20 millimeters - 405 meters in one ton. Theoretical conversion of a ton of reinforcement with a diameter of 14 mm into meters is one of the options, the most inconvenient in practice.

How many rebar bars are there in a ton 14

1000 clients choose us - all because we are professionals, have our own warehouse and offer convenient ways to deliver products. How many meters are in 1 ton of reinforcement with a diameter of 14 mm. This is convenient for large trading organizations and metal warehouses.

The weight of reinforcement 10 millimeters is 0.617 kilograms. The footage in a ton does not depend on how the 14 mm reinforcement is cut, measured or unmeasured, sold in rods or in a coil in the form of coils. Diameter 12 millimeters - 0.888 kilograms.

Please tell me how and what is the best way to decorate a brick wall in the interior?

Answers from forum users and experts to the question: How many kg are in 1m of reinforcement? Have information about how many kilograms there will be in one meter of reinforcement. necessary in any case when conducting construction using this material.

Rebar and reinforcing steel with a diameter of 14 mm, in this case also sold by tonnage. Diameter 20 millimeters - 2,470 kilograms. Based on the above data, we can conclude that a larger diameter corresponds to a greater weight of reinforcing bars.

In 1 ton of reinforcement with a diameter of 14 mm - the number of linear meters of reinforcing rod = 826.45 meters. Diameter 18 millimeters – 2,000 kilograms.

In any case, the number of meters per ton will be the same. With a diameter of 10 millimeters - 1620 meters in 1 ton. Manufacturers of metal profiles and various types of rolled steel release their products for sale, measuring them in tons. With a diameter of 8 millimeters - 2531 meters in one ton. Diameter 14 millimeters - 1,210 kilograms. How many meters are there in 1 ton of 14 reinforcement.

Out of habit, without sufficient experience, it is difficult to quickly “figure out” and convert a ton of reinforcement with a diameter of 14 mm into meters. For example, reinforcement with a diameter of 5.5 millimeters has a weight of 0.187 kilograms per 1 meter.

Weight, depending on the diameter, is distributed as follows: diameter 6 mm-0.222 kg, 8-0.395, 10-0.617, 12-0.888, 14-1.21, 16-1.58, 18-2.0, 20-2 .47, 22-2.98, 25-3.85, 28-4.83, 32-6.31, 36-7.99, 40-9.87, 45-12.48, 50-15.41 , 55-18.65, 60-22.19, 70-30.21, 80mm-39.46 kg. The length will be different for fittings with different diameters. Data for other types of fittings are given below.

So I #8230, tell you that 1 linear meter of reinforcement with a diameter of 12 millimeters #8230, with a diameter of 22 millimeters - 335 meters in 1 ton. With a diameter of 6 millimeters - 4504 meters in 1 ton.

According to these data, a certain relationship can be traced - with an increase in the number of reinforcement diameters, the number of meters in one ton decreases. To carry out work on building a house, it is necessary to calculate the required volume and weight of reinforced structures. The weight of the 16 mm reinforcement is 1,580 kilograms. How much does a meter of reinforcement weigh? , as well as other questions. By the way, for this you will still need to find out how much 1 meter of reinforcement with a diameter of 14 mm weighs.

THIS IS INTERESTING: How to remove rust from bolts and nuts

Extract from the table of reinforcing steels - conversion of tons to meters, for reinforcement with a diameter of 14 mm. In the kitchen, one wall is completely finished with brick. Not everyone needs it.

Find out the cost of construction Ask a question Photos Reviews About the project Construction Bathhouse Cottage Pool Veranda Foundation Fence Gate Roof Roof Insulation Gazebos Soil Garage Brick construction Construction of a frame house Construction of a bathhouse Wooden houses SRO Engineering systems Heated floor Air conditioners Heating Septic tank Chimney Gas supply Electrical installation Water heating Boiler Circus lation pump Heating systems Thermostats Water heated floor Well Apartment renovation Plasterboard ceilings Partitions. These are: Information about the class and diameter can be found in specialized certification documents - GOSTs. With a diameter of 14 millimeters - 826 meters in 1 ton.

For small consumers, individuals, builders, individual craftsmen and small construction contractors, the supply of reinforcement by tons, on the contrary, presents certain inconveniences.

Hot rolled reinforcement. Weight per linear meter of steel rod

The dependence of the mass of reinforcement on the density of steel is obvious, but to simplify the calculations, there are also correspondence tables.

So that you don’t have any difficulties when calculating this expensive material, let’s figure out how much it needs to be used during construction.

When constructing monolithic reinforced concrete structures, steel reinforcement is used, the weight of which may vary per linear meter due to the unequal thickness of the metal rods. Let's look at how to control their consumption step by step.

How to find out the volume of reinforcement?

In drawings and diagrams of steel frames and meshes, designers indicate the weight and length of each assembly element and ultimately summarize the costs of materials in calculations. These design values are relied upon both when drawing up estimate documentation, and when contractors purchase reinforcement, the weight of a linear meter does not change due to humidity, corrosion or other technical conditions.

All these errors are already taken into account to the maximum in the table values. For example, according to the table, the weight of a linear meter of 10 mm reinforcement is 0.617 kg, but small inaccuracies are possible - per ton, according to the standards, they should be no more than ±5-6%.

But these figures assume a confluence of the most unfavorable circumstances, so they try not to allow deviations of more than ±2-3% and prevent possible speculation.

Hot rolled reinforcement. Weight of a linear meter of material.

Section size of rods	Weight 1 linear m.	Reinforcement length in ton	Boundary weight deviations
Ø6	0.222 kg	4504.5 m	±7-9 %
Ø8	0.395 kg	2531.65 m	±7-9 %
Ø10	0.617 kg	1620.75 m	±5-6 %
Ø12	0.888 kg	1126.13 m	±5-6 %
Ø14	1.21 kg	826.45 m	±5-6 %
Ø16	1.58 kg	632.91 m	±3-5 %
Ø18	2 kg	500 m	±3-5 %
Ø20	2.47 kg	404.86 m	±3-5 %
Ø22	2.98 kg	335.57 m	±3-5 %
Ø25	3.85 kg	259.74 m	±3-5 %
Ø28	4.83 kg	207.04 m	±3-5 %
Ø32	6.31 kg	158.48 m	±3-4 %
Ø36	7.99 kg	125.16 m	±3-4 %
Ø40	9.87 kg	101.32 m	±3-4 %

Calculation of the amount of reinforcement in fact

You can easily calculate the weight of the reinforcement based only on the length and diameter of the rods, since the density of steel is well known and is 7850 kg/m3. For example, the following condition: reinforcement 12, the weight of a linear meter is unknown, but its length in all frames is 100 m.

We calculate the area of a circle with a radius of 6 mm, multiply by the height (that is, the length of the rods) and by the density of the material from which they are made. When calculating, we neglect the ribbing of the reinforcement. As a result we get: πR2×100×ρSTEEL=3.14×0.0062×100×7850=88.74 kg. After checking the table, we will make sure that the calculation is correct.

At 100 meters of material, the deviation was only 0.06 kg, which easily fits into the maximum measurement error of ±3%.

Control of material consumption on a construction site

In any business, including such as the sale of rolled metal, everyone knows each other very well; accordingly, it is better to ask the foreman who will supervise the work on the construction site about the integrity of the sellers in your city. This specialist knows thoroughly where and why steel reinforcement is used; the weight of a linear meter of this structural material will also not be news to him.

Therefore, do not forget to remind him to collect all receipts and invoices for rolled metal. After all, armed with drawings that indicate the length of the reinforcement of each welded mesh and frame, you can jointly take a fascinating tour of the building under construction and make sure that something has not rolled in the process, or just make sure that the materials are used optimally.

The result of such mutually beneficial cooperation will be a perfectly executed building and your mutual satisfaction.

Source: https://FB.ru/article/138695/goryachekatanaya-armatura-ves-pogonnogo-metra-stalnogo-sterjnya

How many bars of 18 reinforcement in a ton