How to sharpen nail scissors at home

How to sharpen scissors at home: quickly, easily and affordably

Scissors are one of the most common types of household tools. This is explained by the fact that they are used both for household purposes and in professional activities. But the work of the scissors will continue only as long as the cutting edges remain sharp. Dull blades will not allow you to make a normal cut even on the most pliable material. How to sharpen scissors at home, without turning to specialists? This will be discussed below.

Preparation for sharpening

Unsatisfactory cutting can be caused by more than just dull cutting edges. Loosening of the center tie bolt or rivet causes a gap to form between the blades, which impairs the performance of the scissors. Such a defect must be eliminated and then the cutting ability of the tool must be checked again.

Poor cutting can also be caused by contamination on the blades left after processing certain materials. They can be removed using cotton wool or a soft cloth soaked in alcohol or technical solvent. Sometimes such layers may not be visible due to the transparency of the composition, and therefore wiping before sharpening is recommended in any case.

Sharpening using improvised means and tools

There are several ways, based on folk experience, on how to sharpen scissors at home. You do not need a special tool, but only simple available tools. Of course, there are sharpening devices and machines, but they are mainly used when it is necessary to restore the sharpness of blades on professional scissors.

Smooth metal rod

This is the most affordable way to sharpen scissors at home. You will need any small diameter steel rod with a smooth surface. This could be a gypsy needle, an awl, a screwdriver, a pin, or even a simple paper clip.

A little worse, but still possible, is to use a round AA or AAA AA battery.

Spread the scissors so that the rod fits as close to the pinch bolt as possible. After this, lightly pressing the handles, begin to bring the blades together, and move the tool you are using away from you towards the cutting ends. Perform these steps 10-15 times and check how the paper is now cut. If the result is still unsatisfactory, repeat the operation again.

Porcelain cup

Most tea cups have a smooth abrasive surface on the outside of the bottom. It can be used instead of a special sharpening stone.

Open the scissors as far as possible. Apply the bevel of the blade at the top to the edge of the cup and, pressing lightly on it, move it along the abrasive towards you. The movement when sharpening should occur only in one direction, otherwise you may not sharpen, but completely and completely ruin the tool.

Aluminum foil and sandpaper

Probably every housewife has foil in her kitchen for baking food. Take the roll and tear off a piece 20-30 cm long from it. Fold it lengthwise 6-8 times to get a dense multi-layer strip. After this, start cutting the foil lengthwise, using the entire length of the blades. After 10 cuts, check the sharpness and, if necessary, repeat the steps.

Source: https://DomZastroika.ru/byt/kak-zatochit-nozhnitsy-v-domashnih-usloviyah.html

How to sharpen scissors at home: methods and life hacks

High-quality sharp scissors allow you to work quickly and not think about everyday details. But it is not always possible to quickly and easily choose a convenient tool, and the old ones have long since become dull, and working with them is just torture.

It is possible to restore the sharpness of scissors at home. In our article you can familiarize yourself with several methods and detailed instructions on how to do this correctly. After reading the suggested guide, you should not have any problems sharpening scissors.

Therefore, you should not immediately run to specialists for this.

Scissors that can be sharpened

You can restore the sharpness of the following scissors yourself:

construction;
stationery;
manicure

The sharpening method will directly depend on the thickness of the metal from which the working element is made and the size of the tool itself. For example, not all options are suitable for sharpening nail scissors.

Reasons why scissors don't cut

The tool does not cut the required material. Almost every one of us has encountered this problem. There may be several reasons for this problem:

the blades of the scissors are dull;
The fastening that connects the 2 running parts of the tool has become loose.

Each of these problems is solved in its own way. Next, we will look at how to properly sharpen your scissors yourself in each case at home.

The simplest ways to sharpen scissors

So, you have determined that the cause of the tool malfunction is a loose lock. In this case, you must proceed as follows:

Take a screwdriver or pliers. Use these tools to secure the screw on the scissors well. The choice of the necessary tool directly depends on the retainer cap of the two cutting parts.
There are variants of scissors in which the blades are connected with a rivet. In this case, open the scissors, place them on a hard surface and use a hammer to flatten the surface of the plug. You don't need to put in a lot of effort. It is enough to hit it lightly with a hammer once or twice. Otherwise, the scissors will be very difficult to open.

So, you have followed the steps described, but the problem has not been resolved. There can be only one conclusion - the cutting edge of the blades has become dull. Below we will suggest suitable methods to solve this problem.

How to quickly sharpen scissors?

If you don’t have a sharpening machine or a special device, and you need to use scissors right now, then you can sharpen the tool at home using one of the alternative methods.

Method 1

This method will work if you can find sandpaper at home. Sandpaper of any grit level is suitable for our procedure. Follow further instructions. The whole operation will take no more than 2 minutes:

Take a sheet of sandpaper and cut it with scissors.
Repeat the procedure if the tool still does not cut well.
The tool can be used for its intended purpose.

Method 2

The gypsy needle is another quick and inexpensive option with which you can sharpen your own scissors at home. This is done as follows:

Insert a needle between the cutting parts of the scissors. Place it as close to the axis as possible.
Now close the blades very slowly. The needle at this moment will move along the moving parts.
Repeat this sequence several times.
At the end of these manipulations, make sure that the maximum sharpness of the working parts of the scissors has been achieved.

Scissors come in large sizes. In this case, the needle should be replaced with a regular glass bottle. Everything must be done exactly the same. But it is necessary to take into account the fact that if you choose one of the methods considered, the effect will in any case be temporary. If you use this tool quite often, then sharpening it will require more thorough actions.

How to sharpen scissors correctly?

If you are determined and ready to take a thorough approach to restoring the sharpness of the scissor blades, you are willing to spend a little money and time to do this - you should take one of the options proposed below into your arsenal.

Method 1

You should purchase a special sharpener from hardware stores or hardware stores. With this device you can easily restore the sharpness of the blades on all household knives and scissors.

Method 2

A special device can restore the sharpness of your scissors even at home. If you have this device in your household, then you are most likely already familiar with the technology of tool sharpening.

During the restoration work, certain rules must be followed. Some people are most likely familiar with them, but I would like to remind you again:

The working elements must be guided towards you along the grinding disc.
The blades of the scissors must be sharpened from the ends of the joint to the node.
The sharpening angle should be maintained in the range from 60 to 75 degrees.

In the absence of an electric sharpening apparatus, a special sharpening stone can be an alternative. In this case, it will be necessary to hold the stone with one hand or fix it on some convenient surface.

Useful tips

When sharpening scissors, you need to follow some rules:

Handle all sharp objects carefully.
Try to fix problems with a faulty tool using the simplest solutions first.
If you do not have certain skills, then do not start sharpening on an electrical device. You may not be able to maintain the required angle of inclination or you may injure yourself.

After reading our article, you can quickly and correctly sharpen scissors at home. This will save you the money and time needed to go to a professional sharpener, and the necessary work that needs to be done with scissors will not be postponed indefinitely.

Source: https://ratatum.com/%D0%BA%D0%B0%D0%BA-%D0%BD%D0%B0%D1%82%D0%BE%D1%87%D0%B8%D1% 82%D1%8C-%D0%BD%D0%BE%D0%B6%D0%BD%D0%B8%D1%86%D1%8B-%D0%B2-%D0%B4%D0%BE%D0 %BC%D0%B0%D1%88%D0%BD%D0%B8%D1%85-%D1%83%D1%81%D0%BB%D0%BE%D0%B2/

When and how to sharpen a manicure tool correctly

Choosing and purchasing a manicure tool is only half the battle, since it requires constant and high-quality maintenance and sharpening.

New scissors or forceps can become dull after just a few uses, and some need to be brought into good working condition immediately after purchase. It all depends on the quality of the metal and the initial characteristics of the tool.

What does a manicurist need to know about sharpening manicure tools? Is it possible and how to sharpen nail scissors, tongs and cutters at home? How to evaluate and accept a job in the service? Let's look at all the questions in order.

Types of sharpening

There are two directions:

Conveyor or factory processing
Manual sharpening

The factory one is of lower quality and often the sharpness is lost after the first 10-15 uses. Even if the blades are initially very sharp, they dull much faster compared to manual processing. Also, the blades may have different sharpness along the length, which is why forceps or scissors tear the cuticle and leave burrs.

Sharpening by hand requires experience, knowledge and skill. It is better to contact a professional in the workshop to get the desired result. Many craftsmen try to sharpen scissors and pliers at home using improvised tools. Yes, perhaps the sharpness will be enough for a couple more procedures, but after that it is still lost, and the service technician has to do more work to eliminate the consequences of home sharpening.

What professional equipment is used for sharpening manicure tools?

Where can you sharpen nail scissors, tweezers, and cutters if you have given up on home experiments and decided to entrust the tools to a professional? There are special workshops that carry out maintenance of manicure equipment.

On average, the cost of such a procedure starts from 300 rubles, and varies depending on the city and country of residence. Many craftsmen in big cities complain that the cost of the service is almost comparable to the purchase of new tools, but this is only if you compare inventory of low and medium price categories. If you are working with high quality products, it is better not to take risks and contact a workshop.

There are two types of professional sharpening machines:

The first ones are equipped with a diamond-coated metal grinding wheel, which, when rotated, grinds down the edges of the tools, giving them the desired sharpness. The method keeps the tool durable and does not shorten the service life.

A laser machine is easier to use, but it wears down the metal faster, making it more fragile. Where to sharpen manicure tools after this? Of course, where the craftsman does it with a high level of quality, regardless of what machine is used.

Basic rules for sharpening tools

There are several key points that make up the algorithm for servicing manicure equipment. If all points are completed, we get the desired result.

When closing scissors, forceps or cutters, nothing should prevent the handles from coming together. If such a problem arises during work, they must be taken to the workshop and all interfering or protruding parts must be ground off on the machine. At home, you can do this with a sharpening stone or rasp, being careful.
Nippers, cutters and scissors should not dangle, there should be no gap between the cutting planes and at the point of connection of the handles.
The cutting planes of the nippers should be smooth and close without gaps under gentle pressure.
The convergence of the cutting edges in the nippers should be uniform from one edge to the other, and not wavy: first the tip, and then the heel, or vice versa.
The blades should not have protrusions or burrs that catch, scratch or cut the skin.
The outer edge of the pusher should be sharper than the inner one, and the inner one should have a straight line without jagged edges. The main task of the tool is to move the skin, not cut it.

When sharpening, all factors must be met to obtain the desired result.

Sharpening of pliers, skin tongs, tweezers. If the cutters are loose, they are stuffed at the junction of the blades. They should walk softly and close in an even line. The inside of the nippers is ground down to a straight line from the inside. When closing, the blades should be in the same plane, neither higher nor lower than one another. If there are burrs on the tips of the cutters, they need to be sanded down.

Sharpening pushers. After processing, they should be sharp, but not cut the skin. They should also not scratch the nail. If the pusher falls and bends, the edge is leveled and then ground down. The pusher is always sharpened on the outside, and only polished on the inside. It is necessary to ensure that the outer edges are not sharp; they should also be ground and sanded.

All types of pushers - comparison, characteristics, operating rules

Sharpening nail scissors.

If the blades were deformed after a fall, the edge will have to be ground down. If the damage is significant, then most often the scissors cannot be repaired. If the deformation is small, then grinding helps eliminate it, but the length of the blades will be reduced.

When sharpening scissors, only the front surface is removed. You cannot go into the rear one; it was processed only once at the factory, and this is enough for the entire operating cycle.

After each grinding of a layer, it is necessary to remove the metal grain from the blades so as not to damage them when closing.

Nail scissors - types, proper use, choosing the best

The sharpening angle of the scissors must correspond to the factory rake angle and cannot be changed. Usually it is 60-75°.

At the final stage, it is recommended to go over the blades with fine-grained sandpaper to remove burrs.

Sharpening manicure knives. They are used mainly for pedicures, to remove rough skin and corns. The manicure knife should not be very sharp; the factory angle should be maintained and the edge should not be ground into a bayonet.

How and with what to check the sharpening level

Even a professional manicure cannot be done with a blunt instrument. That is why regular maintenance of tongs, scissors, and tweezers is necessary. With a large flow of clients in the salon, maintenance of scissors and cutters may be required once every two to three weeks. With a lower flow - much less often.

To understand when it's time to sharpen your manicure tools, there are a number of simple tests. They will require the following materials to choose from:

Thin plastic bag
Stretch film
Dried wet wipe made of non-woven material
Elastic vinyl, latex or nitrile gloves

These same tests will allow you to check the quality of the work performed by the master. In the workshop, these tests are used to check each of the processing stages of blades and cutting edges.

Methods and instructions on how to check the quality and level of sharpening:

We fix the thin plastic bag so that the edge is even. Unclench the scissors, tongs or wire cutters, place the edge of the bag between them, and close along the entire length. The blades should not tear, snag or pull the polyethylene.
Stretch film is the most demanding material for checking the level of sharpening. The principle is the same - we fix the film and close the blades along its entire length. The cut should be smooth.
A napkin made of non-woven material demonstrates well the presence of burrs on metal. With high-quality processing, the cut is smooth, without snagging on the blade.
Vinyl or nitrile gloves should be secured between the thumb and forefinger, the cutting edges should be completely opened and closed, placing the glove sheet between the blades, and then pulled down slightly towards you. Often scissors or tongs cut well at the base, but the closed edge pulls the glove and tears it. This means it's time to sharpen the blades again.

Proper sharpening of manicure tools at home

How to sharpen manicure tweezers, scissors and nippers at home? This can be done at home using a grinding wheel or by hand. If you don't have experience with this, it's better to ask someone who has tried it or knows how to do it. Otherwise, you need to take the manicure tools to the workshop.

THIS IS INTERESTING: How to remove varnish from copper

If you still decide to carry out the procedure at home, you will need:

Sharpening stone or rasp
Sandpaper, hard and sanding
Any of the above materials to check the level of sharpening

A block or rasp is suitable for processing large areas. They should work smoothly, respecting the factory angles. Next, the blades are sanded with sandpaper. It can be secured with tape to the handle of a spoon or a wide nail file for additional support.

You can get by with just sandpaper, first 600 grit and then 1500 grit, to smooth out any burrs on the metal.

Some craftsmen use foil folded in 4-8 layers, finely cutting it with a tool to the desired degree of sharpening. Reviews about this method are mixed, so if you have an expensive, high-quality instrument, it’s better not to risk it.

Everyone should mind their own business, and if possible, it is better to have the tools serviced by a professional. If you decide to do the treatment at home, follow all recommendations.

Source: https://nails-mag.ru/instrumenty/zatochka-instrumentov-dlya-manikyura-zatochka-manikyurnyih-nozhnits-kusachek-pusherov/

How to sharpen scissors at home correctly, tips

You cannot do without this tool either at home or at work. We're talking about scissors. If the cutting edges have become dull due to prolonged use, you should not rush to get rid of the tool - it is quite possible for it to return to its previous properties. The easiest way is to take it to a workshop, but this will take some time. Once you figure out how to sharpen scissors at home, you can do the job yourself. The most unexpected objects are used for this purpose.

Why don't scissors cut?

The reason should be sought not only in the wear of the cutting part, but also in the fastening. You need to carefully inspect the tool, evaluate how tightly the blades fit together, whether there is a gap or play between them - such problems are eliminated first. If the cutting edges seem quite sharp, but the scissors are chewing on the material or paper, the fasteners are probably loose. Therefore, you should not rush to sharpen - you need to try to tighten the fastener.

If the work blades are held together with a screw or screw, you will need a screwdriver or pliers. The lift is performed after preliminary opening of the scissors. Turn the screw half a millimeter and see how well the blades move. Non-removable fastening causes certain difficulties. The open scissors are placed on the anvil, the locking stop is carefully flattened with a hammer, and then the cutting ability of the tool is checked.

A thin lubricant helps ease the movement of the scissors. After dripping a little onto the connecting axis, you need to open and close the tool several times. You immediately feel that the canvases began to work faster and easier. If the problem lies not in the fixation, but in the blades, the scissors will need to be sharpened.

Over time, any scissors become dull and require sharpening.

Sharpening methods

Only scissors designed for everyday use can be sharpened independently. To process a manicure, thinning or tailoring tool, you will need a special machine with an appropriate attachment and an experienced craftsman. If you try to manipulate it at home, you can ruin the item.

A quick result is achieved using a simple metal sponge, available to any housewife. During the sharpening process, small particles of material fly in all directions, so it is better to work directly over a trash can. Cutting the sponge must be done with the entire blade; the sharpness of the cutting parts depends on the number of cuts.

Grindstone

Not everyone knows how to sharpen scissors with their own hands. Many people use a fine-grained stone, the size of which allows it to process the entire surface at once. The angle for sharpening blunted scissors must correspond to the value specified by stamping at the factory.

The blade should slide along the stone from the attachment point to the tip, and it is necessary to make confident movements with your hand.

It is worth remembering the obligatory condition - do not change the angle and from time to time easily rub the inside of the scissors against the sharpening stone to remove the formed burrs.

If the stone is of high quality, your efforts will not be in vain - after an hour, the scissors will regain the desired sharpness and begin to work perfectly.

Sandpaper

The tool can be sharpened with sandpaper, the grain size of which is 150–200 microns. The sheet is folded in half so that the side with the abrasive powder is directed outward and comes into contact with the blades during processing. As you begin to cut the paper into strips, you can soon feel how the scissors become sharper.

In the process, the entire working length of the blades is used - from the attachment to the tips. This sharpening option is suitable in cases where the tool needs to be slightly “tweaked” or nicks and burrs need to be removed. A very dull blade can only be sharpened on a sharpening machine.

After such a procedure, all that remains is to wipe the scissors with a dampened paper napkin to collect the crumbs remaining from the abrasive sandpaper.

Foil

Another simple way to return the sharpness of scissors is with regular foil, which housewives use for baking. Take a sheet 20–25 cm long and fold it like an accordion to make a thick strip. The sharpening effect after the next cut depends on the number of layers. Cutting is performed along the entire length; the final result depends on the number of movements.

Sewing needle or awl

This affordable method is suitable for sharpening small tools. You will have to act carefully, otherwise nicks will form on the canvas. It is necessary to insert the needle between the blades of the scissors, then begin to slowly cut it. With a little practice, you can increase the speed.

The needle can be replaced with a pin, knitting needle or awl - the essence of the technique remains unchanged.

Glass

You will need an unnecessary jar, since after sharpening the scissors, chips and scratches remain on it. For small tools, it is recommended to use a glass bottle with a narrow neck. Sharpen the blades as follows:

cutting movements are performed on the glass, the blades should slide, and the can or bottle should move back;
from time to time check the sharpness of the scissors on the fabric - as soon as the indicator becomes satisfactory, the procedure is stopped;
scissors are wiped to remove glass chips.

Traditional methods are good because they can be done at home using available materials. Unfortunately, such procedures do not restore sharpness to the level that a professional specialist can do with the appropriate equipment.

Prevention and care tips

To ensure that the tool remains sharp and reliable in operation, certain recommendations should be followed during operation:

Some sources claim that scissors are boiled for disinfection purposes. This opinion is erroneous, because the tool begins to rust. For this treatment, purchase an antiseptic at a pharmacy kiosk, which is used to wipe the blades.
Approximately once every six months, the mechanical part is lubricated with sewing machine oil. It is enough to apply a few drops to the opening of the axis. For this procedure, you can use olive or castor oil. By lubricating the attachment point, you can protect the tool from corrosion.
It is not recommended to disassemble the scissors mechanism - not every product can be reassembled.
The item should only be used for its intended purpose. No matter how sharp the blade is, improper use will quickly damage it.
It is forbidden to grind the metal along the entire blade; sharpening is performed at a certain angle at which convenient cutting is carried out.
Before sharpening, you need to check the condition of the edges. It is possible that nicks and burrs are interfering with normal cutting.
Before you start sharpening, be sure to clean the blades from dirt. For such a procedure, it is best to use a solvent or alcohol.

If the tools are used for professional purposes, it is better to take them to a workshop. Only an experienced specialist knows how to sharpen scissors and give them the necessary sharpness.

The sharpening procedure with your own hands is possible, but you still should not “run” the scissors until they are completely dull, using the appropriate tools for certain types of work. You need to make sure that the cutting object does not become the child’s favorite toy.

The baby begins to experience sharpness on any objects around him. By following simple rules, you can maintain the functionality of scissors for a long period without resorting to emergency sharpening methods.

It should be remembered that purchasing a high-quality tool today is quite difficult, since the market is flooded with Chinese-made products that do not have the proper quality of metal.

Source: https://posuda-expert.ru/svoimi-rukami/118-kak-zatochit-nozhnitsy-v-domashnikh-usloviyakh

Over time, any scissors become dull and cut materials much worse. Don't rush to throw them away. Save on your purchase: restore the sharpness of the blades; fortunately, there are several simple and accessible ways to do this at home.

How and what to sharpen

The easiest way to revive office scissors and a hair clipper. With nail scissors the situation is more complicated: you will need a small block with a fine abrasive.

Advice
If scissors with curved ends become dull, it is better to buy new ones or contact a professional, as it will be difficult to sharpen them yourself.

Available sharpening methods:

whetstone - sold in hardware and construction stores;
foil;
sandpaper;
file.

Even though the blades are dull, they can still cut your hands. Therefore, it is highly advisable to work with protective fabric gloves and with care.

Special sharpener

A sharpening stone (a block, less often a circle) has two sides: low- and coarse-abrasive. We need to start with the last one.

How to operate the sharpener:

The stone is placed on a piece of cloth (to avoid slipping and damage to the surface) and lightly moistened with water.
The scissors are opened as wide as possible or disassembled - if the design allows.
Extreme care or experience is required when working with a whetstone. The most important thing when sharpening is to maintain the height of the blade angle. The factory tilt cannot be changed.
The blade is sharpened with movements in one direction (away from you). It is important that it goes completely across the stone, otherwise the scissors will cut the materials unevenly.
After sharpening on the rough side of the stone, the procedure is repeated on the fine-grained part.

Manicure scissors are sharpened according to the same rules, but on a special small sharpening stone. The best sharpening items are coated with diamond chips.

Tip
To check the sharpness of a sharpened object, cut a piece of synthetic fabric with it. This kind of material is quite difficult to cut. If it works the first time, the device is sharpened.

Foil method

This way you can quickly sharpen your manicure scissors.

How to properly sharpen scissors with foil:

A sheet of ordinary foil is folded in several layers - this way the effect will be noticeable faster.
The folded sheet is cut into several strips. The more there are, the sharper the object will become.
Remains of foil are removed from the blades with a dry cloth.

This method is an excellent preventive measure for scissors: as soon as they start to work worse, the blades are corrected by cutting the foil. This way you can also relieve stress.

How to sharpen scissors at home: 4 easy ways

How to use a file

Sharpening scissors with a file takes longer than using other methods. To bring the blades into working condition using this method, it will take about an hour of continuous effort.

The device is fixed on a flat surface or held with one hand. The blades are alternately drawn along the file from the attachment point to the very tip.

You need a fine-grained file. As with the whetstone, you will need a steady and experienced hand. Sharpening is carried out at an angle made at the factory, and it cannot be changed during the process - otherwise the device will be ruined.

Sharpening scissors correctly is half the battle. The item must be used correctly: cut only what it is intended for, wash off dirt, wipe dry and store folded. Preventative home sharpening is carried out once every 2-3 months with regular use of the device. If scissors lie idle for a long time, they are sharpened once a year.

Often the reason for poor operation of the device is not due to dull blades, but to a loose fastening. Just tighten the bolt and the item will work like new. Another common reason is adhered dirt, glue from office tape, etc. You need to wash the blades with soap and a stiff brush, then wipe dry. Stubborn plaque is removed with soda, vinegar or alcohol.

Home sharpening allows you to quickly correct scissors, but an ideal result is obtained only with the work of a master and the use of special equipment. In addition, if home methods are used incorrectly, the instrument can easily be damaged. Therefore, it is better to carry out only preventive sharpening yourself, and in case of severe dullness, contact professionals.

Source: https://womenburg.ru/sovety/3632-4-sposoba-zatochit-nozhnicy.html

How to sharpen scissors at home yourself - Website about

Scissors are an indispensable attribute in any family. Over time, their blades lose their sharpness. Fortunately, almost any scissors can be sharpened.

How to prepare scissors for sharpening

Before you start sharpening, check whether the performance of the blades is actually affected by dullness. Sometimes scissors may not cut well due to the loosening of the connecting element. It could be a bolt or rivet.

After fixing all the problems, cut something and thereby check whether sharpening is needed. If the blades do not cut well, you will need to sharpen them. Before use, wipe the knives with a cotton swab and an alcohol solution. Remove more stubborn stains using suitable chemicals.

Self-sharpening methods at home

There are many ways to sharpen scissor blades at home. To do this, you can use improvised materials that are found in almost every apartment.

Needle or awl

To sharpen you will need a thick needle or awl. The method is quite energy-intensive, so it is suitable for processing small scissors.

Cut the selected item from the rings to the tips of the blades. Try to guide the needle along the sharp edges. Your actions should not be performed through force.

You can use either new or used metal sponge. The softer the sponge, the better.

Cut the sponge with scissors, using the entire surface of the blades. The more cuts you make, the sharper the blades will be. Please note that during the procedure the sponge crumbles a lot, so it is better to cut directly above the trash can.

Glass jar or bottle

In this procedure, it is best to use an unnecessary jar, since after sharpening there will be scratches on the glass.

Take the jar in your hand and make the required number of cutting movements. During sharpening, the entire surface of the blades should touch the glass.
After work, carefully remove small glass fragments from the surface of the blades.
If you need to sharpen small scissors, use a glass bottle with a narrow neck.

Special sharpeners

A special sharpener can be purchased at a hardware or construction department or ordered from an online store.

Open the scissors and slide each blade through the designated hole. Do the required number of passes until the blades become sharp.

File

Open the scissors to their maximum width and hold with your hand where the blades meet. This will allow each half to hold tightly and not become loose during the procedure.

File the inside of each blade at a 70 to 80 degree angle. Make movements either only from yourself, or only towards yourself. Never saw the blades by jerking back and forth. Just a few movements are enough to sharpen.

If you cannot hold the scissors tightly with your hand, use a vice.

Grindstone

A similar stone can be purchased at a hardware store or hardware store. Before sharpening, separate the scissors into their component parts by unscrewing the central screw. Apply each blade in turn to the stone with its sharp side and make several movements towards or away from you until the desired sharpness is achieved. At the end of the procedure, assemble the halves by connecting them with a central screw.

Grinder

To use a sharpening machine, sufficient experience and dexterity is required.

The machine is a device with a rotating abrasive wheel. Simply turn on the device and place the halves on the sharpening disc.

In the procedure, it is extremely important to know what angle must be maintained between the blade and the wheel, as well as how long to sharpen, so if you are not familiar with the device, give preference to another method.

Paper clip

Please note that the larger the paperclip, the better.

Hold the paper clip tightly with the tips of the blades and slowly, squeezing the scissors with your fingers, draw it to the base. Repeat the procedure until the scissors are sharp enough. You'll know the scissors are sharpening when you notice small nicks in the paper clip.

Battery

In a similar way to a paper clip, you can sharpen scissors using an unnecessary AA battery. Please note that the battery must be in a metal casing. Clamp the battery with the blades and move it to the base the required number of times.

Screwdriver

Since the paperclip or battery is quite small, it can be replaced with a screwdriver to sharpen larger scissors. Place the screwdriver, metal side down, on a hard surface. Pinch it with the tips of the blades and slowly move it to the base. Repeat as many times as needed to keep the blades sharp.

Where can you sharpen scissors?

Typically, this service is provided in key-making or shoe repair shops. The cost of sharpening scissors is from 50 rubles, depending on the complexity of the service.

THIS IS INTERESTING: How to properly cut metal with a grinder

Subtleties of the sharpening process

Depending on the type and purpose of the scissors, sharpening may have some subtleties and nuances.

Regular

Scissors that cut paper or other materials can be sharpened at home, spending very little time. Use foil, sandpaper, or another metal-coated object to sand the blades.

Kitchen

At home, it is best to sharpen kitchen scissors in a way that does not require disassembling them. Foil, sandpaper or metal sponge work well. However, such sharpening will not provide long-term results. For better processing, contact professionals.

Manicure

High-quality manicure scissors are quite difficult to sharpen at home. To do this, you need to know how to properly tighten the connecting element and what the sharpening angle should be. The blades are processed with a special diamond needle file from base to tip.

Hairdressers

Hair cutting scissors are made from high-quality materials, as they are designed for a long service life. Properly sharpening blades at home is very difficult and risky. Entrust sharpening to a professional who uses special laser equipment for the job.

Thinning

Thinning scissors have a special structure. They consist of double blades - serrated and straight. It is impossible to sharpen such an item at home, since the work requires certain equipment and knowledge.

Tailor's

It is extremely important when sharpening fabric scissors not to leave jagged edges on the blades, so use smoother materials for processing, such as foil or zero-grade sandpaper. After sharpening, be sure to check the quality of the cut on an unnecessary piece of fabric.

If these are zigzag scissors for processing the edges of fabric, then they can only be sharpened in a workshop.

Garden

For sharpening, you can use a whetstone or a machine. Disassemble the scissors into their component parts and sharpen them accordingly.

To process metal scissors, be sure to maintain a sharpening angle of approximately 75 degrees. In preparation, separate the blades by unscrewing the connecting bolt. You can sharpen knives with a file or sandpaper. After the procedure, treat the parts with an anti-corrosion agent to extend their service life.

Sheep

Such scissors require maximum sharpness, so processing with foil or sandpaper will not work. Blades must be sharpened using a machine with an abrasive wheel. Process each blade separately, opening the halves as wide as possible.

Non-separable

Scissors cannot be disassembled without a connecting bolt. For sharpening, choose simple methods that do not require separating the halves, such as using a needle, foil or sandpaper.

Best quick ways

If sharpening is needed urgently, use methods that do not require disassembly. The following can serve as a sharpening tool:

foil;
clip;
needle;
screwdriver;
battery with metal casing;
glass jar or bottle;
kitchen metal sponge.

Please note that these methods are not suitable for all types of scissors.

What not to do when sharpening scissors

To avoid ruining the sharpness of the blades:

Do not try to sharpen non-standard scissors (hairdressing scissors, thinning scissors, manicure scissors) yourself. Their sharpening requires the use of professional equipment.
Maintain the sharpening angle corresponding to the factory one. If handled incorrectly, the blades will become unusable.
Do not disassemble the scissors if you are not sure that you can put them back together.

Why don't scissors cut?

It happens that the blades retain their former sharpness, but the scissors still do not cut. In such cases, you need to check for a gap between the knives and also see if the cutting edge is broken.

How does a gap occur?

Due to increased loads, over time, the connection of the halves weakens slightly and a gap appears between the blades. Sometimes it happens that the metal of the knives becomes slightly deformed. To ensure that the scissors cut well again, adjust the mount or align the blades.

Cutting edge irregularities

Over time, the metal of the blades wears out and becomes deformed. To level the cutting edge, you should contact a professional craftsman who will sharpen and polish the surface of the edge.

How to adjust blade stroke

To adjust the fastener that affects the gap:

If it is a bolt, carefully tighten it using a small screwdriver. Be careful not to over-tighten; if you tighten too much, the halves won't be able to move.
If the connection is a rivet, open the scissors and place it on a metal surface. Then use a few blows of a hammer to flatten the plug.
If there is a stop at the junction of the halves, open the scissors and carefully sharpen it.

How to keep scissors sharp at home

To keep your blades sharp for as long as possible, follow these simple rules for using them:

Do not use boiling to disinfect. It is better to wipe the blades with an antiseptic.
Treat the mechanism for connecting the halves with any oil once every 6 months.
Use scissors only to cut materials that are suitable for their intended purpose.

Always wipe the blades with a piece of cloth after use. Store scissors in a special case and do not allow liquids to come into contact with the knives.

How to remove rust from scissors

If the metal is covered with rust, it can be removed using special or improvised means. Special substances easily cope with plaque and do not spoil the metal. However, such funds are not always available at hand, and they are quite expensive.

An alternative to store bought substances can be substances that are available in almost every apartment. You can remove rust with:

slurry of water and soda;
solution of citric acid or vinegar;
peeled potatoes.

If the rust has not yet become deeply ingrained into the metal, the blades can be cleaned with sandpaper or a metal sponge.

Scissors are a simple item that requires simple operating rules. Some types of them require special sharpening only in professional workshops. To process regular blades, you can use materials that are always on hand. At the same time, the procedure does not require any special skills from you, and also will not take much effort and time.

Source: https://knaschool50.ru/uborka/kak-natochit-nozhnitsy-v-domashnih-usloviyah-samostoyatelno.html

How to sharpen scissors at home - Cleaning Master

Many people prefer to throw away scissors that have become dull. But it’s better to learn how to sharpen scissors, and thereby save significantly on their purchase.

After all, now on store shelves you can only buy modern, unreliable Chinese fakes.

Preparation

The easiest ones to sharpen are stationery scissors and haircut scissors. It is much more difficult to sharpen a manicure set. Before sharpening them, you need to make sure that the malfunction is due to dullness.

It is quite possible that their fastening axis is simply weakened, where a bolt or a simple rivet is mainly used. Just tighten the bolt.

If the screw is tightened tightly, but the scissors still do not cut well, then sharpen the stop heel, which is located near the hole with the bolt.

Do not try to close the blades, as this will make the situation worse.

If a rivet is used at the joint, tighten it. But before that, open the scissors and place them on any metal object.

Then, using a bit, flatten the rivet and check how well the blades close.

If nothing has changed after these steps, you will need to sharpen the scissors at home.

Procedure

To sharpen scissors, you need to use a whetstone. It can be purchased at many hardware stores.

Most stone varieties have two different sides, one being fine-grained and the other being coarse. You need to use the rough side first.

How to sharpen scissors yourself? The algorithm includes several steps.

Place the whetstone on a cloth and dampen it a little with water.
If a bolt is used as a fastening on the scissors, then disassemble them. If using a rivet, open the blades as wide as possible.
Make sure that the factory sharpening angle is maintained. Don't change it. It is required to lay the blade in such a way that its plane tilts away from itself.
Make sure that the chamfer is parallel to the surface of the block.
Sharpen the scissors correctly, slowly move the blades along their entire length and only in one direction.
Once you have sharpened them on the rough side of the stone, start sharpening them on the other side. Do the same steps.

Once you've finished sharpening, test the scissors on a piece of fabric. If they are well sharpened, they will cut the material evenly while hanging without any problems.

Sharpening nail scissors: how to do it right

To sharpen nail scissors correctly, you need to use a small whetstone with a fine grain.

Give preference to sharpening stones with diamond chips.

Nail scissors can be sharpened in the same way as regular ones. But this should be done as carefully as possible.

This is especially true for sharpening the inclination of the cutting chamfer, since it differs from others.

If your nail scissors with curved blades become dull, it is easier to buy new ones.

The only thing that can be corrected in them is the bolt.

How to sharpen garden shears

To sharpen garden shears yourself, you need to disassemble them.

First, unwind them. This will be required to sharpen the blades along the entire length.
To sharpen the bottom concave blade, use a whetstone with a radius of no more than 3.5 cm.

All other actions are similar to those described above.

Quick Methods

In order not to waste time disassembling and turning the presented tool, you can use the following methods.

Sandpaper. Find a small piece of this material, fold it in half, with the rubbing side facing up. Start cutting the paper into about 15 strips. In the same way, you can use an abrasive material on fabric, metal wool.
Aluminium foil. Take a sheet up to 25 cm in size and fold it several times. Then start cutting it.
Glass jar or bottle. If you want to sharpen small scissors, you can use the neck of a bottle. Place open scissors into the neck of the bottle and begin to carefully connect the rings.
Cutting a sewing needle. It will help sharpen your nail scissors.

How to use the tool correctly

In order for the presented instrument to retain its sharpness for a long time, you should adhere to some recommendations.

If you use scissors to cut fabric, then use the tool only for this purpose. Then you don’t need to use it to cut fish, cardboard and other objects.
Other scissors are used to cut zippers and metal threads.
If you use them for cooking, caring for plants and nails, then disinfect them regularly.

The main thing is not to boil the scissors, but treat them with a simple antiseptic. Otherwise, they will quickly become dull and rust. Don't forget to lubricate them every six months.

How to sharpen thinning scissors at home

Are your kitchen or nail scissors dull? Don’t want to give them to sharpening specialists, but can’t do without this tool? It's OK! So that you can restore the former sharpness of its blades yourself, let's look at how to sharpen scissors at home.

Can scissors be sharpened?

Experts who work with such tools almost unanimously say that it is almost impossible to sharpen them efficiently at home. It is best to immediately take such products to a workshop, where they will be processed using a special machine. Only such a machine will allow you to get a perfect cutting edge, and is guaranteed not to damage the tool.

The same methods for sharpening scissors that are used at home (including sharpening with an emery stone) can only slightly improve the situation.

But more often they lead to the fact that the blades of the scissors begin to cut the material unevenly, and over time they become even more dull.

That is why it is recommended to use traditional methods of dealing with this problem only in extreme cases, when it is not possible to go to a workshop. Let's look at acceptable sharpening methods at home in more detail.

Method 1 - sandpaper

This is the simplest and most affordable option for sharpening scissors at home, which is recommended for use in cases where the blades are not very dull. To complete this you will need a small sheet of paper. It is advisable to take a sample with an abrasiveness of 150-200, but you can try working with coarser materials. Next, you will need to cut this paper, performing about 20 cutting movements, and then simply wipe the blades with a napkin.

If you don't have sandpaper on hand, you can use steel wool or sandpaper instead. The effect will be the same.

Method 2 - foil

How to sharpen nail scissors if you don’t have any special tool at hand for this purpose? A sheet of ordinary foil will help you. You will need to act like this:

To begin with, a sheet of foil will need to be folded several times to form a dense strip of material.
You will need to cut this strip of material with scissors. If you make a few thin strips, you can sharpen the scissors well, but if you stop at just a few wide ones, just sharpen your tool slightly.
Next, you just have to remove the remaining foil from the blade with any napkin.

how to sharpen scissors using foil:

You can use this method to keep your blades sharp. Use it every time you notice that the scissors are cutting worse.

Method 3 - sharpening with a whetstone

This procedure will require a lot of time and effort from you, but it will allow you to get good results if performed correctly. It is recommended to contact it for those people who already have experience working with a sharpening stone. It is recommended to act like this:

First you need to select a fine-grained stone for this purpose. Any other type of it will not only not give you the desired result, but can also ruin the product.
Next, you need to determine the angle at which the product was sharpened by the manufacturer. You will need to maintain the same angle as you work.
After this, you will need to place the blade at the set angle on the sharpening stone so that it lies flat on it.
When you are sure that everything is prepared correctly for work, you can proceed directly to sharpening. The movement of the blade itself on the sharpening stone in this case should be from the stud to the tip of the tip along the working surface. You will need to process the two cutting edges of the scissors in this way. On average, all this work will take you about an hour.

sharpening with a whetstone:

Make sure that you do not change the level of inclination of the blade while working. This will negatively affect the quality of sharpening and in many cases can even lead to damage to the tool.

It is also extremely important during such work to remove all burrs that form on the blade from sharpening. Otherwise you will get an uneven cutting edge.

Method 4 - touchstone

How to sharpen scissors correctly if you have a special whetstone for this purpose? In such a situation, you can act like this:

First, you need to prepare the whetstone itself for work. To do this, it should be laid out on a towel and poured with special oil for honing (this is sold in the same department where the whetstone itself is). If you don’t have such an oil on hand, you can use any other oil or even water - this will not affect the quality of the material processing.
Next, it is recommended to disassemble the scissors by unscrewing their central screw. In most cases, this can be done with an ordinary flat-head screwdriver.
After this, you should take the blade, place it on the inside of the sharpening stone, select the angle of inclination specified by the manufacturer when creating the cutting edge, and then slowly run the blade along the sharpening stone several times. Usually 20 minutes of work is enough to sharpen it. Repeat this step with the second piece of scissors.
Next, you need to assemble the scissors and test their sharpness on the material for which they are intended (for example, fabric or paper). If you note that you are now satisfied with their cutting qualities, consider the task completed successfully. If not, you will have to repeat all the manipulations with the touchstone from the very beginning.
After completing this process, be sure to wipe the scissors with a napkin to remove any remaining burrs.

Source: https://master-kleit.ru/origami/kak-zatochit-filirovochnye-nozhnicy-v-domashnih/

How to sharpen nail scissors at home

Most women keep wire cutters, scrapers, and tweezers at home. At a minimum, men have nail scissors, because everyone needs to cut their nails. Manicurists, pedicurists, and hairdressers, of course, also have all the above-mentioned work items.

All these tools sooner or later become dull: it is more difficult for tweezers to grab small hairs, cutters stop cutting and tear the thin cuticle, scissors cut nails with force. It is not without reason that master sharpeners call unsharpened nail scissors and nippers blanks: they do not cut or trim the skin, but tear it or cut it off, but only with the ends.

Rice. 1

Sometimes the cheeks of cuticle nippers or the jaws of tweezers differ in length; there is play between the cutting edges.

THIS IS INTERESTING: How to clean silver spoons at home

The length of the canvases may vary: one is slightly longer than the other; or the item will have nicks on the blades. In most cases, the tips and cutting edges of scissors, tweezers, and tweezers are so thick that it is impossible to grab the skin of the roller, bite off an ingrown nail, or pull out an individual thin hair.

Previously, many people simply changed the tool, but now it can be sharpened, and it will serve you for many years. How many times can you sharpen nail or hair tweezers and scissors? Much depends on the steel and the quality of production of manicure products. It can be sharpened manually or using professional equipment. And for this you will need the help of a master.

In the vast majority of cases, a purchased factory product has to be sharpened and adjusted. Often, factory-made blanks are not calibrated: the blades have play and do not grip hairs or skin tightly. The exception is expensive products from Stalex, Mertz, Jaguar, Kedake, etc. Please note that we check products before sale: if the factory sharpening is not enough, we sharpen it.

By the way, it is important to understand the names of the parts of scissors, tweezers and tweezers. Look at the picture.

Manual sharpening of manicure tools at home

It is not always possible to order a service from a professional workshop. You can try to do this at home yourself, but you need to acquire the appropriate skills.

Please note that some scissors are made with a serrated edge: you cannot sharpen these at home, you will have to take them to the workshop. Sharpening tweezers and tweezers is very difficult, and you will not be able to adjust them at home without the appropriate equipment. Scrapers (pushers) also need regular sharpening. Considering that they should not be sharp, they should also only be sharpened by a professional.

But it’s quite possible to sharpen nail scissors with your own hands. The outer side of the blade is sharpened first, then the inner.

You will need the following supplies and accessories:

A machine with a diamond wheel of fine abrasiveness (you can take a diamond-coated knitting needle with the finest abrasiveness, but you will have to work like a whetstone: with hand movements.
Felt cloths for polishing.
Polishing stones with abrasiveness of 8,000 and 12,000 grit.
2000 grit sharpening stone.

Tools can be unscrewed before sharpening to make it easier to sharpen edges and blades.

To start sharpening the edge, turn on the grinding wheel at minimum speed and move the edge of the edge in a circle from its beginning to the end: the contact patch should be 0.2–0.3 mm.

The blades are sharpened first from the inside, then from the outside. The scissors, if they have been disassembled, are twisted, the edges are wiped, then they are polished with whetstones already assembled.

Disadvantages of home processing

If you are not used to it, you may not calculate the pressure on the edge and bend or break it.
Due to incorrectly selected grinding wheel abrasiveness, it is possible to leave nicks in the processing area.
It is impossible to eliminate the backlash and adjust the smoothness of the ride.
Only scissors and knives can be properly sharpened at home.

Why is it important to trust the sharpening of manicure tools to professionals?

Often, when purchasing manicure kits on websites, buyers trust the sellers, while in the vast majority of cases the product sold is either from a factory-sharpened supplier or is frankly of low quality.

Factory sharpening may not be enough, even if we are talking about a product from a reputable company. When conveyor processing of products occurs quickly, there is no need to talk about quality. The disadvantages of this approach are immediately visible: the heads of the pliers and the blades of the scissors can be scratched, there is visible play, bends, the cheeks of the pliers and the jaws of the tweezers vary in length and width.

In any case, a self-respecting retailer will check the quality of sharpening. Control of manual processing is very scrupulous, so the cost of the procedure is 3–5 times higher than the cost of wholesale processing of manicure instruments. In Moscow, sharpening can cost up to 500 rubles: it depends on the type of product. You can see the exact prices for sharpening services on our website.

Manicure scissors

First, the master checks the smoothness of movement and the precise closure of the blades. Adjusts travel settings. Burrs on the metal are removed, the rivet is corrected, the blades are sharpened on both sides, and final finishing is done.

The working area should ultimately be free of nicks, stains, soot, and noticeable roughness.

The tips of the cuticle scissors should have the same length and width, fit tightly but softly against each other, close together without difficulty, and there should be no play between the edges. This is a good sharpening.

You can check the quality of processing by cutting a napkin or fabric. The scissors should go into the material like a knife into butter, leaving an even cut line.

The blades should close very softly, without jerking. If the scissors are closed with force, the edge will shrink when closing, rolling over the cutting edge and dulling it.

There should be no kinks, roughness, or excessive polishing on the edge of the cuticle scissors, as this will lead to the cuticle slipping out from under the blade. But for hairdressing scissors, a sign of high-quality processing is just perfect polishing, when the blade literally glides through the hair. The stroke of hairdressing scissors should be soft.

With regular use of scissors, the treatment will last for about 4 months. If scissors are used at home, the treatment may even last for 2–3 years.

Wire cutters

First, the master eliminates the backlash that almost 90% of tools have, even those that just left the factory. The blades are sharpened on both sides, the contact area is checked and the closing area is trimmed. In the picture you can see what the blade closure area looks like after high-quality processing.

Source: https://vi-pole.ru/kak-tochit-manikjurnye-nozhnicy-v-domashnih.html

Manicurist mistakes when working with scissors | imkosmetik magazine about manicure and beauty

An integral part of a combined manicure is a cutting tool. In this article we will talk about nail scissors, selection rules and mistakes when working with the tool.

Tool selection

Sharpening

Common Mistakes

The most popular manicure scissors

1. Tool selection

First of all, for comfortable work you need to choose the right tool. This may take a lot of time, since one master is more comfortable working with a longer tip of scissors, and another with a short one. We have already written in more detail about the features of choice in the article “How to choose nail scissors?”

2. Sharpening

The next important factor before starting work is sharpening. Not even the most expensive but dull scissors will help you make the perfect cut. Only a sharp, well-sharpened tool can become an assistant in performing high-quality manicure. If you have a large flow of clients, then this procedure will be necessary about once a month. For those who do manicures for themselves and friends, sharpening is also necessary, but the tool will remain sharp 2-3 times longer.

How do you know when scissors need sharpening? Everything is very simple. Simply roll up a lint-free hand towel and make a slit. If the ends have chewed on the fabric, then you should put the instrument aside and have it sharpened in the near future. I think that finding a sharpening specialist will not cause you any difficulties. If you have any doubts about a particular workshop, you can always inquire and ask for advice from the members of the imkosmetik group.

3. Common mistakes

Most of the mistakes occur among beginners and those who do not do this professionally. It happens that masters still do not absorb the information from the courses and do it incorrectly. Below we will look at a list of the most common mistakes made by craftsmen when working with scissors:

Incorrect grip of the tool. The most important thing is to hold the instrument correctly. Nail scissors are something different than stationery scissors. (We take the scissors with the tip away from us, the curved tip should point to the left. The thumb is in the upper eye, the ring finger is in the lower one. You need to pinch the joint of the blades with your index finger, and the middle finger is a support.)

Using the entire canvas. When removing the cuticle, we do not need the entire blade; we only need the tips - ⅓ of the entire blade (the end of the scissors stroke).

The blades collapse when cutting. The canvas should be perpendicular to the nail plate. You can’t push it away from you or onto yourself, because of this the cuticle is not cut off, but chewed.

Cutting the first step. The first cut starts from the bottom near the side roller. It is necessary to insert the scissors under the sinus by 1 mm. When squeezing the blades, the skin should be white, so the cut will go correctly and you will not injure the client. If the skin turns red, then a cut is inevitable.
Big steps. The cutting steps should be small, thanks to this you can achieve an even cut. With wide movements, the cuticle will be cut unevenly, which will lead to the appearance of hangnails after a few days.

4. The most popular nail scissors

There are many brands and models of scissors on the market, but each of us is in search of the best. What should you pay attention to? The surface of the scissors must be smooth and without damage, the blades must converge without gaps and at one point, and the most reliable materials are nickel, medical steel and zinc. All of these characteristics converge in several brands, which are listed below. They occupy a leading place and are popular among manicurists:

Zinger is the most widespread brand, their tools are considered the best on the market;
Yoko – have a special method of hardening steel, serve for a long time;
Staleks have gained a reputation as the most reliable tools.

Among the scissors, I can highlight several favorites, in which everything is perfect for me:

A combination manicure is the ideal technique for me and most of my clients.

If you have also chosen a combo for yourself, then do not forget that scissors are your faithful assistants that require attention and sterilization; you can read more about this here “Sterilization of manicure instruments.”

Finding a tool can take an indefinite amount of time, because everything is learned through experience. I hope that these tips will reduce your search time and help you perform a manicure perfectly and efficiently.

Tatiana Sorokina

Source: https://imkosmetik.com/journal/oshibki-mastera-manikyura-pri-rabote-s-nozhnitsami/

How to sharpen nail scissors at home

Hangnails, unattractive nails and a bad mood are the results that can be achieved by using dull tools. You have two options: go out and buy a new set or take a few minutes to learn how to sharpen nail scissors at home. Have you chosen?

What is the easiest way to sharpen nail clippers and ruin them?
How to properly sharpen manicure tools at home
Professional sharpening of manicure instruments
Tips for caring for nail clippers and scissors

The easiest way to sharpen nail clippers at home and ruin them

If you've already looked through the Internet a little, you've probably come across the same type of popular advice on sharpening manicure tweezers. We will tell you about them right away so that you understand what not to do and why.

Sharpen manicure tools using foil or sandpaper

The advice goes like this: take the foil, fold it in several layers and make several cutting movements with scissors or tweezers. It’s the same with emery, only it needs to be folded in half, with the rough side out.

So, never use this method! The short-term sensation that the scissors have become sharper comes from the fact that the serrations on the cutting edge are being ground. Ultimately, the sharpening angle will change so that no craftsman will be able to restore the tool.

Want a clearer argument? Imagine a dull knife. Will cutting the foil at a 90 degree angle help sharpen it? No, on the contrary - the knife will become dull! To sharpen a knife, a sharpener is used at a certain angle to change the shape of the cutting edge. The scissors also need to be adjusted to the correct angle.

Advice. It is important to maintain the correct sharpening angle - for manicure scissors from 45 to 69 degrees.

How to sharpen nail clippers and say goodbye to them

Among the tips on how to sharpen nail clippers at home, in addition to foil and emery, it is recommended to use a regular whetstone. Any hardware store sells this. The grain size of a 50 ruble bar is not suitable for straightening and sharpening manicure tools. The whetstone will leave rough marks on the cutting surface of the nippers or scissors, which will be difficult for even an experienced craftsman to get rid of later.

We recommend that you learn how to properly iron a pleated skirt at home.

Cleaning a microwave is not a cumbersome process at all. You can find out how to quickly clean a microwave here.

The only suitable option is a fine-grained stone or a diamond-coated grinding wheel.

How to sharpen manicure tools at home

Scissors from the nearest store for 200 - 400 rubles. quickly fail. They are distinguished by not very high quality steel and the price of sharpening is comparable to their cost. So it’s up to you to decide whether you should extend the life of your tweezers by professionally sharpening them or buy new ones.

To slightly increase the service life, we will tell you several ways to sharpen and avoid damaging nail scissors at home.

Devices for sharpening manicure instruments

As we have already said, foil, sandpaper and other methods widely advertised on the Internet are a myth. The short-term effect goes away, leaving a completely damaged instrument.

It’s not for nothing that women’s cunning is glorified by poets and ill-wishers, so let’s put it into practice. Give your man a universal pocket sharpener “for everything” for the next holiday. Be sure to make sure that the kit includes a cone-shaped “spoke” with diamond (what we need) coating. For example, LANSKY BladeMedic looks like this:

You will kill two birds with one stone: firstly, the man will definitely like the gift; secondly, along with his knives and fishing things, he will sharpen your nail scissors. Or you can sharpen it yourself.

There is no need to look for and order this particular sharpener - only the principle is important: the presence of a small, thin musat with the correct coating and grain size.

If you have a 1000-grit whetstone, we suggest watching the video at the end of the article about sharpening manicure tools. The sequence of actions is clearly visible.

How to sharpen cuticle nippers

One of the reasons why cuticle nippers begin to tear and pull the skin is backlash. Take the tweezers by the handles and swing them relative to each other. If you feel movement, you need to tighten the middle screw.

Learn how to remove paint from a paint roller.

We'll tell you how to quickly dry jeans after washing here.

How to make a frame for a picture or photo from cardboard, read here: //o4istote.ru/sovety-po-domu/kak-sdelat-ramku-iz-kartona/

Open the tweezers by pressing on the handles. First, apply the diamond rod to the inside cutting edge. Use smooth, unidirectional movements to sharpen it. When the bevel shines with new, shiny metal, the result has been achieved. The next stage is the outer edges, follow exactly the same pattern. Close the tweezers and check: the gap between the cutting surfaces should be no thicker than a hair.

Important! Tools must be sharpened in one direction. Movements “back and forth” are unacceptable!

How to sharpen nail scissors

Here we will tell you how to sharpen nail scissors using a conical diamond rod. Shiny stripes are visible on the cutting halves of the scissors - this is the place where they rub against each other. This “contact patch” should be no more than 0.5 mm. If the strips are wider, it will take considerable effort to get the tool in order.

It is better to disassemble small scissors for easier handling. Using smooth movements of the diamond sharpener in one (this is important!) direction, remove the metal from the cutting surface. The task is to reduce the “contact patch” to 0.2 - 0.3 mm. Having processed both halves in turn, assemble and snap tightly, as if pressing, the scissors. Lightly sand the cutting edges again. Ready!

Professional sharpening of manicure instruments

The most reliable way to sharpen nail scissors or tweezers is to take them to a nail technician. Having once splurged on expensive and high-quality tweezers, do not even try to straighten the cutting edge yourself at home without experience - you will completely ruin it!

The price of the service ranges from 200 - 500 rubles, a good sharpening will last at least six months - a year, if you do not do manicure professionally.

Consider the cost of the tool, possible risks and the cost of sharpening.

Tips for caring for nail clippers and scissors

Beautiful, well-groomed nails are impossible without good tweezers and scissors. To extend the life of manicure accessories, you must follow several rules:

clean after each use;
regularly lubricate rubbing parts with oil;
never use manicure tools for other purposes;
Proper storage is in a horizontal position in a special case.

We hope you learned something new for yourself and avoid mistakes by following “harmful” advice. Tell us in the comments, have you tried sharpening scissors with foil? Have you sworn off doing this?

Source: https://goodhozyayka.club/uslovie/kak-natochit-manikyurnye-nozhnitsy-v-domashnih-usloviyah.html