How much does 1 meter of reinforcement with a diameter of 12 mm weigh

How much does 12 mm reinforcement weigh?

For a long time I gathered my courage to start building my own country house. To carry out the work of pouring the foundation, it was necessary to use a large amount of reinforcing bar with a diameter of 12 millimeters. I immediately had a question about how much 12 mm reinforcement weighs, but I will write about this below.

Rebar and concrete are inseparable

Getting acquainted with various country house construction projects on the Internet, I saw that a large number of house elements are made of monolithic concrete. It is these structures that require the expenditure of materials for reinforcement.

The weight of the reinforcing bars required for reinforcing the structure is calculated by multiplying the total length of the entire reinforcing bars by the weight of one linear meter of reinforcement.

The weight of one linear meter of reinforcing bars is a constant unit. The weight of a linear meter of reinforcing bars depends on the composition of the steel used in the manufacture of the reinforcement, as well as on its cross-section.

Knowing the mass of the reinforcing bars, you can estimate the degree of reinforcement of the structure, which depends on the ratio of the mass of the reinforcing bars to the volume of concrete used when pouring the structure. By the way, you can simply use an online calculator for the foundation.

Important! The degree of reinforcement allows you to calculate the cost of the structure.

How much does the fittings weigh?

The weight of a meter of reinforcing bars with the same steel alloy composition completely depends on the diameter of the reinforcing bars and the cross-section of the reinforcing bars.

With a diameter of reinforcing bars equal to three millimeters and a cross-sectional area equal to 0.071 square centimeters, the specific weight of such reinforcement is 0.055 kilograms per linear meter.

With an increase in diameter by one millimeter, the cross-sectional area is 0.126 square centimeters, and the weight of one meter of such reinforcement is approximately 0.098 kilograms per meter.

With a diameter of a metal reinforcement bar of five millimeters, the cross-sectional area increases to a value equal to 0.196 square centimeters, while the weight increases to a value equal to 0.154 kilograms per meter.

When using reinforcement with a diameter of six millimeters, the cross-sectional area is 0.385 square centimeters, while the mass of one meter is 0.222 kilograms per meter. In principle, this can be found out from the reinforcement weight table.

Source: https://dom-fundament.ru/skolko-vesit-armatura-12-mm.html

Weight of a pack of reinforcement

Aluminium, duralumin
Copper, bronze, brass
Tin
Lead
Zinc

It is easy to check this value or find it for rods of a different diameter; the calculation uses basic formulas relating mass, specific gravity and dimensions: V – volume of one linear meter, obtained by multiplying the cross-sectional area of the rod (3.1415 D 2 /4) by its length (in our case – 1 m).

There are standards regulating the minimum permissible proportion of longitudinally placed reinforcement in reinforced concrete products; for example, for a monolithic foundation strip it is 0.1% of the cross-sectional area. In addition to knowing the weight and footage of reinforcement in one ton, when choosing, pay attention to the following indicators: Parameters of the ribs on the profile: dimensions, pitch, angle of inclination, width.

The cost of one meter of 12 mm reinforcement varies from 29 to 32 rubles and depends on the type of steel, season and other market factors. For reinforcement with a diameter of 12 mm, V = 0.000113 m 3, ρ is the density of steel, the standard value is 7850 kg/m 3. In general, the percentage of steel in reinforced concrete products is quite small, but taking into account the fact that its specific gravity exceeds the density of concrete at least three times, the total mass of the frame or mesh needs to be known and taken into account.

Type of rolled products - to strengthen concrete building structures, hot-rolled bars are required (read about the types of reinforcing bars).

An important nuance: the actual weight of 1 meter 12 mm of reinforcement does not always coincide with the calculated one. Accordingly, one ton includes 1126.12 m. It can be welded without problems, provides excellent adhesion to concrete, has good corrosion resistance, toughness and strength. Of course, the calculation results are averaged; in reality, the rods do not have a perfectly round cross-section, but a corrugated surface.

But the data obtained is sufficient to determine and verify the required amount of material. A400 weighs the same (0.888 kg/l.m), it is recommended for strengthening particularly stressed structures; the connection of the rods to each other is carried out exclusively by viscous. Responsible suppliers indicate this value in their price lists; in fact, each manufacturer has its own.

Of all the classes offered in private and residential construction, A3 reinforcement made of A400 or A500C steel is most in demand.

When purchasing rods with a fixed length individually (in small batches), this fact does not play a special role, but when ordering in bulk, you need to double-check how much the 12 mm reinforcement weighs, in particular, one meter of it. Products are sold in dimensionless coils or in the form of rods from 6 to 11.7 m; if necessary, they are cut into pieces of the required size at small retail outlets.

How much does a meter of reinforcement with a diameter of 12 mm weigh? Knowing the weight of one linear meter of reinforcement is required to calculate the amount of material of a certain diameter in a ton and its weight in a future building structure. The length of the rods and the form of delivery (in coils or in the form of measured sections). Other characteristics taken into account.

The parameter is controlled by GOST, but taking into account the manufacture of products from different types of steel and differences in the sizes of the ribs, the deviation varies from 0.2 to 3% in both directions.

The amount of relative elongation (within 14%). The minimum grade for prestressing and load-bearing elements made of concrete is corrugated reinforcement with a diameter of 12 mm, as a result, it is the most in demand. Thus, one l.m. with a diameter of 12 mm it weighs 0.888 kg.

The standard weight (mass) of 1 meter of round reinforcement with a diameter of 12 mm is 0.888 kg, this parameter is standardized according to GOST 5781-82. Type of steel, its yield strength, admissibility of use in welding joints. The specified formula is also used to determine the total length of the purchased reinforcement, taking into account its weight.

The scope of application includes road construction, production of reinforced concrete products (including piece goods), welded frames and meshes.

THIS IS INTERESTING: How to properly connect aluminum to copper

Temporary tensile strength. This value is standardized and varies depending on the cross-section of the rods. The latter is the cheapest to build due to the reduced content of alloy metals and is considered almost universal. Most often, the price is indicated for one ton (from 30,000 rubles and above), the larger the purchase volume, the lower the acquisition costs.

Weight of a pack of reinforcement

How much does 1 kg of 12 reinforcement weigh?

The main area where reinforcement is used is construction. The reinforcement is produced in the form of rods and is used as a basis for strengthening reinforced concrete structures. It takes the main bending and tensile loads, giving reinforced concrete strength, durability and reliability.

The most popular in construction is reinforcement with a diameter of 12 mm, due to the fact that it is quite convenient and lightweight. But, at the same time, when knitting frames and meshes, such reinforcement has the necessary rigidity. In addition, when constructing a strip foundation, which is used mainly for brick country houses, the diameter of the mesh with which the foundation is reinforced should be minimal. 12 mm reinforcement is also used for this.

How much does 1 meter of 12 mm reinforcement weigh?

When estimating the cost of building a house, it is important to know the weight of 1 meter of 12 mm reinforcement. But, it is necessary to calculate this value only if there is no house design or if the diameter of the reinforcing mesh changes. As a rule, the weight is calculated for each structure separately and indicated in the building design.

The total weight of the reinforcement in the entire structure is calculated by multiplying the entire length of the rods by the weight of one linear meter of reinforcement. Knowing the weight of all the reinforcement, you can calculate its market value. But you need to know how much 1 meter of 12 mm reinforcement weighs.

You can calculate this indicator yourself. To do this, you need to take the product of the length of the reinforcement (in this case, 1 meter), the specific weight of the reinforcement (7850 kg/m3) and the area of the circle with the squared diameter.

That is, the weight of 1 meter of 12 mm reinforcement is equal to: 1 m x 7850 kg/m3 x (0.785 x 0.012 m x 0.012 m) = 0.887 kg.

You can purchase reinforcement from construction companies, both by meter and by weight. Since the demand for reinforcement is currently quite high, it is needed not only by large construction companies, but also by small teams building houses. Therefore, reinforcing materials can be purchased in large quantities or in ultra-small wholesale.

When selling, the price of reinforcement per meter is generally indicated, but large companies have now begun to indicate the cost of reinforcement per ton. In this article, a calculation was made of how much 1 meter of 12 mm reinforcement weighs, so you can easily purchase reinforcement that costs both per meter and per ton.

Find out the cost of construction Ask a question Photos Reviews

Construction
- Bath
- Cottage
- Pool
- Veranda
- Foundation
- Fence
- Gates
- Roof
- Roof
- Insulation
- Gazebos
- Priming
- Garage
- Brick construction
- Construction of a frame house
- Construction of a bathhouse
- Wooden houses
- SRO
Engineering systems
- Warm floor
- Air conditioners
- Heating
- Septic tank
- Boiler room
- Chimney
- Gas supply
- Electrical installation
- Water heating
- Boiler
- Circulation pump
- Heating systems
- Thermostats
- Water heated floor
- Well
Renovation of apartments
- Plasterboard ceilings
- Partitions
Good afternoon. I am engaged in construction work. Sometimes I make them to order. It's a lot of work, but you can earn decent money. Now I urgently need a large amount of fittings. I don't know what to bring her with. How much does 1 meter of reinforcement weigh, with a diameter of 12 mm?

Answers from forum users and experts to the question: How much does 1 meter of reinforcement with a diameter of 12 mm weigh?

We will make a garden wheelbarrow from sheet iron, a metal profile and two old wheels from a car. Using a metal profile, we create a lower frame for the wheelbarrow, connecting the parts either by welding or bolts. We make a trough from sheet iron in the form of a box with a sloping side. We connect all this by adding two handles and wheels.

Answer or clarify the question

Luxury apartments in Moscow

Popular questions

How to make heating for free?

I live poorly. There is no money for repair work. And we still need to do heating. And I want to somehow do it for free. But my problem is that I don’t know what it is.

What are the reviews on the forums about the construction of wooden houses?

Hello my dear expert. I want to build myself a wooden house, but I’m still hesitating, maybe brick would be better. Therefore, please tell me. please, any reviews.

How to make a house project from foam blocks?

To build any house, both brick and foam blocks, you need to make a house project. At this point I would like to know how much it will cost to do the project.

How to choose the power of an electric boiler

The walls are not insulated, the windows are metal-plastic, Uzhgorod

Tell me where I can get, view or download color tables for choosing colors for design

Baby room design

Simple and at the same time stylish design of a room for a baby. A comfortable crib is the center of the image; it is decorated with soft toys that the baby will play with.

Intelligent production DPR

The republic has launched the production of unique composite polymer reinforcement, which can be used to reinforce concrete structures. The company Kompozit Group LLC has already received a state certificate of conformity.

Composite reinforcement (fiberglass reinforcement) is an excellent solution for construction, because the material has excellent adhesion to concrete. Therefore, this type of reinforcement is applicable for the construction of buildings and structures, foundations below the zero ground level, lighting poles, power line supports, insulating power line crossarms.

The main advantages of fiberglass reinforcement:

• Unlike traditional materials, non-metallic reinforcement is 3 times stronger.
which allows the use of a smaller cross-section and is 9 times lighter, which greatly simplifies transportation and installation. • Resistant to corrosion . alkaline environment of concrete and most aggressive environments.

Its service life significantly exceeds the service life of metal fittings.
• Little weight . (AKP-4, where a diameter of 4 mm weighs 0.02 k7, when metal reinforcement with a diameter of 6 mm (6A-III) weighs 0.260 kg per linear meter).

• The coefficient of thermal expansion is close to that of concrete, which eliminates cracking due to temperature changes.

• The tensile strength of composite reinforcement is 3 times higher than that of steel.

• Low thermal conductivity . It is not a cold bridge, which significantly reduces heat loss. When exposed to low temperatures, its properties remain the same.

Information: Kompozit-Group is a dynamically developing research and production company specializing in the production and implementation of innovative reinforcing elements made of composite materials, offering composite fiberglass reinforcement AKS d=4mm - 20mm from a warehouse in Shakhtersk.

Contacts: +38(066)-672-05-55, 071-306-15-39

Read 542 times

1 Comment

We have already started receiving questions. Some questions can be answered by following the links in the news. But it’s not difficult for us to answer again: 1. How much does 100 meters of 4-kid weigh? Answer: 4ki weight per linear meter: 0.02 kg 6ki -0.05 kg, 8ki - 0.07 kg, 10ki - 0.12 kg, 12ki - 0.2 kg, 14ki - 0.26 kg 2.

What is the maximum length you can produce? Answer: we can pull it to any length (just have time to thread the thread and add polymer). But we wind the bays, usually 25 - 50 meters long. This will make it easier for you to unwind. 3. What is the diameter of the skein? This is important for transportation. A skein from 4-10 mm in diameter - 1 meter From 10 - 12 mm - 1 meter 30-40 cm 4.

We are interested in your fittings for a greenhouse. But we don’t know how it behaves when bending and what diameter to use.

Answer. If the greenhouse is supposed to be 1 meter in height, then 6-8 mm reinforcement can be used. If you are human height or 2-2.5 meters, take 12mm.

Leave

Source: https://armaturasila.ru/skolko-armatury/skolko-vesit-1-kg-12-armatury.html

How much does 1 meter of reinforcement 12 weigh?

Very often, reinforcement is used to strengthen a particular monolithic structure or casting. By definition, reinforcement is various kinds of rods and profiles consisting of metal structures of any type of metal.

In construction, this term is heard quite often, since the issue of strengthening the structure under construction is quite tough and acute. Basically, reinforcement is used as a means of connecting concrete mortar and its coupling between cast profiles of a building or structure.

Application of fittings

As a rule, the question of using one or another type of reinforcement is quite relevant, and often completely constant, among builders and engineers. The connection between these two specialties is quite simple. Each of them wants the structure they built to stand as long and as strong as possible. In addition, there are laws and regulations for this, established by the state construction standard.

To strengthen the structure under construction, reinforcing iron blanks of various strengths and thicknesses are used. Basically, their use is inextricably linked with the concept of reinforced concrete material. As a rule, a reinforced concrete element, be it a slab or a block, consists of some kind of frame - metal reinforcement, on which there is a shell of concrete mortar.

This type of building element can significantly increase the load per unit surface area. As a rule, such structures use metal of relatively soft density, such as an iron rod, channel and other workpieces.

But it happens that to strengthen the structure, denser and heavier material is used, for example, an angle, an I-beam or other rolled metals. According to their physical and construction characteristics, such reinforced concrete structures have a number of classifications, the basis of which is the strength class of reinforced concrete.

Thus, the following classes of reinforced concrete structures are distinguished:

Hot rolling design.
Manufactured concrete structures using thermal and chemical treatments.
Durable.
Thermally resistant design.

Certain characteristics assigned to the enormous strength and stability of reinforced concrete structures in construction depend on these classifications and a number of strengths.

For any building material, a distinctive characteristic is GOST, according to which manufacturers of reinforced concrete structural elements roll out the material. It is this standard that regulates the use of one or another type or strength class of reinforcement in concrete mortar.

Clutch nuances

As is clear, the mass of a given reinforcing bar 12 directly depends on what shape and what size it is. It is known that the plane of the rod reinforcement itself can have a smooth surface or have corrugation.

It is worth saying that the best adhesion to concrete mortar occurs due to the corrugated surface of the reinforcement, which is a kind of connecting link between the strength and hardness of the structure.

The entire range of reinforcing material varies depending on how and in what way it was produced. In other words, there are both hot-rolled and drawn rods. It is worth noting that the quality of hot-rolled reinforcement is much better than that of another system of reinforced concrete blocks. But reinforced concrete reinforcements produced by a cold roller have their own number of classifications and advantages in subclasses.

For the basis of correct adhesion of absolutely any reinforcement, it is necessary to know the weight and mass of the metal. It is on the basis of these parameters that one or another type of seam is formed, which is adapted to a given reinforcement. This can be either cold welding or ionic bonding of the metal.

Where is the reinforcement used?

The most common diameter in reinforcement for its use is a 12 mm layer. This diameter is considered the most convenient and optimal among similar reinforcement systems produced with similar diameters. It is also noteworthy that reinforcement with such a diameter is quite easy to bend and itself has a low mass. But when tied together, the reinforcement forms sufficient strength and hardness necessary to hold multi-ton structures.

Moreover, for the construction and erection of walls in cottages and private houses, according to the standard, a reinforced foundation must be used, which is reinforced with 12 mm reinforcement.

In this option, a strip foundation is used, which also provides for the installation of metal structures for pouring concrete.

To correctly calculate the cost of the required amount of reinforcement with a diameter of 12 millimeters, you need to know its weight over a length of one meter.

But such calculations are necessary only when the structure does not have a layout in the established order, or the process of replacing the reinforced foundation with a higher-quality layer of reinforced concrete occurs. All main characteristics of all structures must be recorded in the documentation for the construction of the facility.

How to calculate the weight of reinforcement?

In order to calculate the mass of the reinforcement used, you need to know some of the minimum parameters of a given metal structure, and these are:

For an accurate calculation, it is necessary to multiply the total length of the reinforcement used by its linear meter. Also, it is not difficult to calculate the cost of fittings. To do this, you need to know the price per meter of length of reinforcement with a diameter of 12 millimeters.

For ease of calculations, it is best to use a special table of reinforcement data, which is available in any specialized hardware store. These tables indicate the ratios of length, width and density of each reinforcing material, as well as their specific gravity calculated per cubic meter.

When purchasing a small quantity of reinforcement, its weight is indicated in kilograms. But if the purchase occurs in higher mass quantities, then tons are used to indicate weight. In any case, if you know the price of 1 meter of reinforcement with a diameter of 12 millimeters, you can easily calculate the cost of cash costs for the total length of the reinforcement.

Reinforcement weight

For the accuracy of construction work, as well as for calculating the funds spent on reinforcement, it is necessary to know its weight and other parameters.

Finding out the weight is quite simple: to do this, you need to add up the total weight of all the rods used for construction and divide the amount by the number of linear meters.

But linear meters have different price characteristics, which are also related to the parameters of the fittings, in particular the diameter. To do this, you need to use the calculation table of reinforcement parameters, which indicates that reinforcement with a diameter of 12 millimeters has a weight of 0.88 kilograms per length of one meter.

Obviously, to calculate the cost, it is necessary to know all the parameters of this type of reinforcement that are associated with the linear meter. So, in one ton of rods with a diameter of 12 millimeters there are 1126 meters of reinforcement.

Source: http://poznaibeton.ru/beton/ves-metra-armatury.html

How much does a meter of 12 mm reinforcement weigh, required for constructing a foundation?

The construction of houses involves the construction of the foundation of the building, so different foundation designs are erected. Depending on the material from which the house is built, one or another type of foundation is suitable. One of the main elements of the base is the reinforcement strapping, which gives strength and flexibility to the concrete structure.

The most common metal rod for foundations is 12 mm reinforcement. You cannot underestimate the dimensions, because this indicator is already minimal. Before installing formwork and pouring the foundation, it is necessary to calculate the number of metal products that need to be delivered to the site.

In this regard, the question arises: how much does a meter of reinforcement with a 12-mm section weigh?

Types of metal rods for foundations

Reinforcing metal products are manufactured in accordance with GOST, which is a regulatory legal act of the Russian Federation and obliges manufacturers and developers to adhere to the required parameters specified in the document.

To determine how much a meter of reinforcement-12 weighs, you need to know what types of products are produced. There is hot-rolled steel with 6 strength classes, thermomechanically hardened steel, welded steel and composite polymer reinforcement.

The latter is the lightest in weight of all the others, if we take the same diameter for comparison, because it is made of a special lightweight material.

How to calculate weight

To determine how much reinforcement-12 is in a ton, three methods are used. First, you can weigh one or more rods of the same diameter and a certain length. After this, divide the ton by the weight result and calculate the quantity. The second option is designed for use in calculations of the nominal diameter of the product, which is equal to the cross-sectional size of a smooth rod.

The third way to solve the simple problem of how much a meter of reinforcement-12 weighs is to use tables with standard technical indicators to determine the weight according to the diameter of the metal product.

Such data is determined by GOST, thanks to which you can quickly find out the quantity per ton, based on the type, type of product, as well as taking into account the material used for manufacturing.

Using GOST in calculations

Metal rods can be smooth or corrugated. With the former, the situation is simpler, because the diameter is the same throughout the entire length of the product. Corrugated ones, in contrast, have a non-uniform surface, which makes it difficult to calculate their weight.

The regulatory document provides different tables defining the diameter of the rod, its weight depending on the strength class, the metal used, the hardening process, rolling, etc. As a result, in order to find out how much a meter of reinforcement-12 weighs, it is necessary, in addition to the diameter, to take into account some indicators.

GOST indicates that a product with a diameter of 12 mm has a minimum diameter between the ribs of 11 mm, and a maximum diameter on the edge of 13.5 mm. Based on these indicators, the estimated area of this product has already been worked out, which is 1.13 cm2. The following is a summary and it turns out that a linear meter of 12 reinforcement has a weight of 0.89 kg.

It turns out that 1 ton of rolled metal contains 1,123.60 meter-long rods to create a strong, reliable foundation. If 12 mm reinforcement is not used, but a larger diameter is taken, then the number of rods, accordingly, becomes smaller.

Why are such calculations needed?

Design and construction are important stages in creating a safe home and the people living there. Calculations become necessary so that every step on a construction site is accurate and correct. The amount of required reinforcement is needed to calculate the strength of the foundation and will allow delivery to the construction site by specialized transport in the required quantity.

And this will at least reduce transportation and loading costs, and reduce labor costs. Therefore, any, even small, construction must involve advance design and calculation of the required material. This is not just about reinforcement; this rule applies to any type of building material, be it brick, block, wood, or even linoleum, laminate, or wallpaper. Everything has an account, because...

Today you have to pay for every centimeter and kilogram.

Source: https://FB.ru/article/291294/skolko-vesit-metr-armaturyi-mm-neobhodimoy-dlya-ustroystva-fundamenta

How much does 1 meter of reinforcement with a diameter of 12 mm weigh?